• Journal of Oral Medicine and Pain
• /
• v.30 no.1
• /
• pp.1-14
• /
• 2005

The maintenance of good oral health in adults is often hindered by oral malodor and periodontal diseases which are known to be commonly caused by some species of Gram-negative anaerobic bacteria, with low sensitivity to common synthetic antibiotics or antibacterial chemical agents. Therefore the development of a nonharmful natural antibacterial oral rinsing remedy against the causative bacteria is thought to be very important. The purpose of this study is to obtain the basic data for development of a nonharmful natural antibacterial oral rinsing remedy using colloidal silver. The author applied colloidal silver solution with concentration of 10, 30, 50, 80 ppm to some strains in species of Prevotella intermedia, Porphyromonas gingivalis, Fusobaterium nucleatum, and evaluated the effects of colloidal silver on the growth of experimental bacterial strains in aspects of minimal inhibitory concentration (MIC), minimal bactericidal concentration (MBC) and growth pattern after incubation for 24, 48, 72 hours. The obtained results were as follows: MIC of colloidal silver solution against experimental strains was 30 ppm in P. intermedia, 10 or 30 ppm in P. gingivalis, and 30, 50, or 80 ppm in F. nucleatum. And MBC of colloidal silver solution against experimental strains was 30 ppm in P. intermedia, 30 or 50 ppm in P. gingivalis, 30 or 80 ppm in F. nucleatum. Therefore it was concluded that colloidal silver exhibited bacteriostatic or/and bacteriocidal effects against some experimental strain. And the inhibition of growth of experimental strains were markedly or considerably exhibited under 30 ppm$\sim$50 ppm of colloidal silver solution for 48 hours$\sim$72 hours in P. intermedia, 10 ppm$\sim$30 ppm for 24 hours$\sim$48 hours in P. gingivalis, 30 ppm for 24 hours in F. nucleatum. These results indicate that the colloidal silver inhibited effectively the growth of some species of Gram-negative anaerobic bacteria by exhibition of bacteriostatic or/and bacteriocidal effects, and can be used as a possible major ingredient of the nonharmful natural antibacterial oral rinsing remedy to oral malodor and periodontal diseases.

• Journal of Wetlands Research
• /
• v.7 no.3
• /
• pp.75-85
• /
• 2005

The Construction of industrial complex areas means the increase of imperviousness rate and the increase of nonpoint pollutant emissions during a rainfall. Generally the retention basin can become the alternative for removing and controling these nonpoint pollutants. Recently Ministry of Environment are trying to change the purpose of retention basins from flooding control to nonpoint pollutant control. In order to propel the stormwater management program, administration plan of stormwater management is enacted in Spring, 2005. Hereafter, in a newly developing area, the best management practices should be established to control the nonpoint pollutant. Landuses of the research area are classified to the categories of the 1st manufacturing industry, metal industry, fiber and chemical product manufacturing industry, etc. Therefore, this research was performed to understand washed-off characteristics of stormwater and to suggest the controling method of nonpoint pollutants. The optimum capacity of the retention basin can be determined by analyzing the relationships among data of rainfall, runoff, washed-off pollutants from the areas. The rainfall analysis using the data of normal year, recent 2, 5 and 10 years shows that the 80% rainfall frequency was occurred on 10mm accumulated rainfall, but which is not considered the first flush effect. However, by considering the first flush effect, the appropriate treatment capacity of rainfall can be decreased to 4-5mm accumulated rainfall. Using the criteria, the optimum capacity of retention basin is determined to $12,000m^3$ in the research area. The washed-off nonpoint pollutant loading from the areas have beeb calculated to 435ton/yr for TSS, 238ton/yr for COD, 8,518kg/yr for TKN and 1,816kg/yr for TP. The mass of 78.3ton/yr for TSS, 20.4ton/yr for BOD, 128.6ton/yr for COD, 4.6ton/yr for TKN and 980kg/yr for TP can be reduced by constructing the retention basin. The sediment accumulation rate is also calculated by $6.53kg/m^2-hr$.

• Food Science and Preservation
• /
• v.24 no.6
• /
• pp.802-812
• /
• 2017

This study was conducted to investigate the quality properties depending on the cultivation methods (general, organic, pesticide-free) of yuza and its various parts (peel, pulp, seed). The contents of hesperidin were the highest in yuza feel grown by pesticide-free method (13.23 mg/g). The contents of naringin presented a higher content in the peel, especially which of the general (4.62 mg/g) showed the highest value. Vitamin C analysis showed the highest content in the peel, significantly varied according to the cultivation method and various parts (p<0.05). Vitamin C value was significantly highest in organic peel, which was 770.02 mg/100 g, whereas among the peel, the pulp and the seed were it the lowest in the seed. The content of total polyphenols were the highest in general peel (0.85 mg/g). Flavonoid content of pesticide-free seed was significantly higher than those of the other yuja samples which was 0.89 mg/g (p<0.05). The DPPH radical scavenging activity was relatively more active in the peel among the above-mentioned three parts, especially the pesticide-free peel was most active, which was 73.94%. The ABTS radical scavenging activity of organic peel was significantly active among the samples, which was 84.47% (p<0.05). Based on these results, it can be said that yuja has variety of useful components in the pulp and the seed as well as the peel: and thus it's hight recommended to develop more varied yuja products.

• Korean Chemical Engineering Research
• /
• v.48 no.2
• /
• pp.275-282
• /
• 2010

A characteristic study of aqueous chlorine dioxide generation from sodium chlorite($NaClO_2$) by an undivided electrochemical cell with different anode materials were performed. $IrO_2$-coated Ti, $RuO_2$-coated Ti and DSA were used as anode materials and Pt-coated Ti electrode was used as cathode. Various electrochemical cell operating parameters such as cell residence time($t_R$), initial feed solution pH, sodium chlorite and sodium chloride(NaCl) concentration and applied current for the generation of chlorine dioxide in an un-divided cell were investigated and optimized. Estimated optimal cell residence times in $IrO_2$-coated Ti, $RuO_2$-coated Ti and DSA anode material systems were around 2.27, 1.52 and 1.52 sec, respectively. Observed optimum initial feed solution pH was around 2.3 in all anode material systems. Optimum sodium chlorite concentrations in $IrO_2$-coated Ti, $RuO_2$-coated Ti and DSA anode systems were around 0.43, 0.43 and 0.32 g/L, respectively. Optimum electrolyte concentration and applied current were around 5.85 g/L and 0.6 A in all anode systems. Current efficiencies of $IrO_2$-coated Ti, $RuO_2$-coated Ti and DSA anode systems under optimum conditions were 79.80, 114.70 and 70.99%, respectively. Obtained energy consumptions for the optimum generation of chlorine dioxide were 1.38, 1.03 and $1.61W{\cdot}hr/g-ClO_2$, respectively.

• Korean Chemical Engineering Research
• /
• v.56 no.1
• /
• pp.85-95
• /
• 2018

In this research, a biofilter system equipped with a biofilter process and a humidifier composed of a fluidized aerobic and an anoxic reactor, was constructed to treat odorous waste air containing hydrogen sulfide, ammonia and VOC, frequently generated from pig and poultry housing facilities, compost manufacturing factories and publicly owned facilities. Its optimum operating condition was revealed and discussed. In the experiment of complex feed, the ammonia of fed-waste air was removed by ca. 75% and more than 20% at the stage of the humidifier and the biofilter, respectively. The toluene of the fed-waste air was removed by ca. 20% and more than 70% at the stage of the humidifier and the biofilter, respectively. Therefore the water-soluble ammonia and the water-insoluble toluene were treated mainly at the stage of the humidifier and the biofilter, respectively. In addition, hydrogen sulfide was almost absorbed at the stage of the humidifier so that it was not detected at the biofilter process. In the experiment of ammonia-containing feed, the ammonia of fed-waste air was removed by ca. 65% and 35% at the stage of the humidifier and the biofilter, respectively. Its removal efficiency of ammonia at the stage of the humidifier was 10% less than that in the experiment of complex feed, due to no supply of such carbon source as toluene required in the process of denitrification. In the experiments of complex feed, ammonia-containing feed with and without (instead, glucose) the addition of yeast extract, the absorption rates of ammonia-nitrogen were ca. 0.28 mg/min, 0.23 mg/min and 0.27 mg/min, respectively. The corresponding denitrification rates in the anoxic reactor were 0.42 mg/min, 0.55 mg/min and 0.27 mg/min, respectively. In addition, in the modeling of bubble column(the fluidized aerobic reactor of the humidifier) process, the value of specific surface area(a) of bubbles multiplied by enhanced mass transfer coefficient (E $K_y$) was evaluated to be 0.12/hr.

• Applied Microscopy
• /
• v.37 no.2
• /
• pp.83-91
• /
• 2007

The present study examined the epidermal changes of adhesive disks which occur during attachment in Parthenocissus tricuspidata using scanning and transmission electron microscopy. Several adhesive disks, each covered with a bract, develop from the shoot apical meristem during early development. In the initial stage, the adhesive disks are club-shaped and their upper and lower epidermis are indistinguishable. However, in the actively growing stage, they become spherical and both epidermis are clearly differentiated into the adventitious roots. Prior to wall attachment, the adhesive disks exhibit adaxial convex and abaxial concave shapes, and electron-dense substances are abundant in the vacuoles of epidermal cells. The peripheral area of the adhesive disk is adhered first to the wall surface, while the central area is drawn inward in a vacuum-like state during attachment. As the attachment progresses and the electron-dense substances continue to discharge, the upper and lower epidermis rapidly undergo deterioration and the disks shrink considerably. At this stage, structural changes of the lower epidermis occur much faster than in the upper one. The discharged substance is accumulated on the wall surface, and this aids the attachment of adhesive disks on the wall for long periods. In this manner, the shape and structure of the adhesive disk epidermis change drastically from initial growth to the mature stage. Further, the role of electron-dense substance and shrinkage of the disk during attachment has been discussed in Parthenocissus tricuspidata.

• Applied Microscopy
• /
• v.37 no.2
• /
• pp.93-102
• /
• 2007

Secretory leukocyte protease inhibitor (SLPI) was known as one of bacterial lipopolysaccharide (LPS)-induced products of macrophage. Macrophages play an important role in the development of inflammatory responses by secreting an array of cytokines and chemokines in a tissue microenvironment. To identify the function and relationship between potent growth factors and SLPI after LPS stimulation, we conducted reverse transcriptase polymerase chain reaction (RT-PCR) and Western blots for the detection of mRNA and protein expression of SLPI and growth factors such as VEGF, PDGF, bFGF after 100 ng LPS stimulation on the RAW264.7 cells. The result of RT-PCR was showed SLPI mRNA expression was increased from 60 min to 48h in RAW 264.7 cells after incubation with LPS. VEGF and PDGF mRNA was expressed highly at initial stage by LPS stimulation. The mRNA of bFGF and type I collagen was very weakly expressed after LPS stimulation. SLPI protein level was increased likely the mRNA levels in RAW 267.7 cells. Additionally, phase contrast and scanning electron microscopic observation demonstrated that the LPS induce the change of morphology of the RAW264.7 cells. From these results, it suggest that expression of SLPI by LPS treatment may associate with VEGF and PDGF expression in RAW264.7 cells.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.42 no.6
• /
• pp.666-672
• /
• 1997

Twenty years' daily mean air temperature data was used to calculate the critical early seeding date(CESD), the optimum heading date(OHD), the critical late heading date for stable ripening(CHDR) and the critical late ripening date(CLRD) for rice seeded on dry paddy in different agroclimatic zones in Korea. The CESD was defined as the first day with mean air temperature of 13$^{\circ}C$, and the OHD as the first day of the 40 consecutive days with mean air temperature of 22$^{\circ}C$ or above after heading. The CHDR was defined as the date after which the cumulative daily mean air temperature would be at least 76$0^{\circ}C$. Lastly, the CLRD was defined as the last day when daily mean air temperature remains above 15$^{\circ}C$. This information was used for the estimation of periods from the earliest date of seeding to optimum heading date, the latest possible date of heading and the latest possible date of ripening in respective regions. For instance, in Suwon, those respective periods mentioned were found to be 104days, 124days, and 165days.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.1
• /
• pp.43-52
• /
• 2000

Deodorization characteristics and removal rate of sulfur-containing odor have been investigated in the soil filter reactors packed with montmorillonites (Mont.), rice hulls(Rh.), and thickening-activated sludge(Ts.). And variation of pH and $SO_4{^{2-}}$ with the removal of malodorous sulfur compounds have been investigated together. As compared removal rate of montmorillonites between wet and dry condition for sulfur compounds through batch test, it showed that wet condition was better than dry one; removal ratio, as wet/dry, was $H_2S$ of 1.2 and $CH_3SH$ of 1.9, and decrease of pH and increase of $SO_4{^{2-}}$ concentration in the wet condition also showed to be larger than in dry condition. In continuous test for biological deodorization experiment, removal rate of sulfur compounds in reactor packed with Mont., Rh. and Ts, was more than 98 %, and the variation of static pressure was maintained stably under condition of SV $150h^{-1}$, LV 4.2 mm/sec and SV $200h^{-1}$, LV 5.6 mm/sec, and in reactor packed with Mont. and Rh., $H_2S$ was 76.4 % to 87.2 % and $CH_3SH$ was 87.8 % to 93.3 % under the same condition. From above results, it ascertained that it can obtain the high deodorization efficiency by inoculating thickening-activated sludge in soil filter using montmorillonites.

• Journal of the Society of Disaster Information
• /
• v.13 no.4
• /
• pp.442-454
• /
• 2017

Biological weapon is manipulated and produced from microorganisms such as bacteria, virus, rickettsia, fungi etc. It is classified as one of the Weapons of Mass Destruction (WMD) along with chemical weapon and radiological weapon. Biological weapon has a number of operational advantages over the other WMDs including ease of development and production, low cost and possibility of covert dissemination. In this study we analyze the history of biological weapon's development and the existing biological threats. Then, we predict the social impact of biological attack based on the physical properties of biological agent and infection mechanisms. By analyzing the recognition, dispersion pattern of agents, characteristics of the diseases in the biological weapon related historical events such as Sverdlovsk anthrax accident, 2001 anthrax attack, we found out some of the facts that biological attack would not likely to be recognized rapidly, produce large number of the exposed, increase number of paients who suffed from severe respiratory illness. It would lead the public health and medical service providers to be struggled with hugh burden. Base on the facts that we found from this case study, we suggested the main capabilities of public health required to respond to bioterrorism event efficiently. Syndromic surveillance and other reporting system need to be operated effeciently so that any suspicious event should be detected promptly. the pathogen which suspected to be used should be identified through laboratory diagnostic system. It is critical for the public health agency to define potentially exposed population under close cooperation with law enforcement agencies. Lastly, massive prophylaxis should be provided rapidly to the people at need by operating human and material resources effeciently. If those capacities of public health are consistantly fortified we would be able to deal with threat of bioterrorism successfully.