• Journal of the Korean Chemical Society
• /
• v.37 no.8
• /
• pp.765-772
• /
• 1993

Two-dimensional potassium tetratitanate ($K_2Ti_4O_9$) and three-dimensional potassium hexatitanate ($K_2Ti_6O_{13}$) fibers have been prepared by the combined method consisting of the flux melting (1150$^{\circ}C$)-slow cooling (cooling rate = 5$^{\circ}C$/h) process from the starting raw materials of $K_2CO_3$, and $TiO_2$ with the flux of $K_2MoO_4$. It was found that the fiber growth reaction is strongly dependent upon the mole ratio of flux (F) to raw material (R), which is 7 : 3 (F : R) as for the optimum growth condition. Relatively long fibers (average length ${\thickapprox}$ 4 mm) with a mixture of $K_2Ti_4O_9$ (major) and $K_2Ti_6O_{13}$ (minor) could be obtained when the reaction was carried out for the $K_2MoO_4-$K_2O{\cdot}4TiO_2$ (F : R = 7 : 3) system, but for the $K_2$MoO_4$-$K_2O{\cdot}6TiO_2$ (F : R = 7: 3) one, only the short fibers with ${\thickapprox}$ 2 mm long could be grown as the mixed phase of $K_2Ti_6O_{13}$ and $K_2Ti_4O_9$.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.605-608
• /
• 2008

This study investigated fundamental properties corresponding to mixtures for the high strength, and their properties of spalling prevention after a fire test. The results were summarized as following. For the flowability of using mixtures for the high strength, the target flow was satisfied with a small quantity of high performance reducing water agent to compare with silica fume. For the compressive strength in the case of using mixtures for the high strength, it was higher to compare with silica fume at 7 days, so it was proved that using mixtures for the high strength was profitable to prevent early frost damage. The compressive strength at the 28 days of silica fume and mixtures for the high strength were similar. There was no reduced tendency at the compressive strength according fiber contents, so it found out that the bonding strength between the fiber and concrete was hardly effective. For the spalling properties, the specimens without fibers were destroyed, however using over 0.05% of NY and PP fibers was effective to prevent spalling on the high strength concrete.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.51 no.3
• /
• pp.187-190
• /
• 2006

In order to produce hemp with low cannabinoids and appropriate fiber yield, seeds of the IH3 (non drug type germplasm) and local variety (drug type cultivar) were mixed to 1:1, 2:1, 3:1 on base of seed weight ratio and cultivated for seed production. In the seed yield trial, the weight of 1000 grains were around 21 g, which was increased in proportion to the ratio of IH3 seeds but seed yield were 100 kg/10a, which were not significantly different by the seeds-mixing ratio. In fiber yield trials with seeds from seed yield trial, fiber yield ranged $193{\sim}198kg/10a$ which was not significantly different by the seeds mixing ratio but the content of THC(${\Delta}$-9-tetrahydrocannabinol) was lowered in proportion to the ratio of IH3 seeds. Variation of THC and CBD (Cannabidiol) level in the 150 plant cultivated with various seed mixing ratio reflected that the percentage of drug and intermediate type were decreased but non drug type were increased in proportion to the ratio of IH3 seeds.

• Membrane Journal
• /
• v.25 no.1
• /
• pp.48-59
• /
• 2015

This paper reports a fabrication of poly(L-lactic acid) (PLLA) scaffold membranes through phase separation process using pure and mixed solvents. Chloroform and 1,4-dioxane were used as pure solvents and mixed solvents were obtained by mixing the pure solvents together. Morphologies, mechanical properties and mass transfer characteristics of the scaffold membranes were investigated through SEM, stress-strain test and glucose diffusion test. Scaffold membranes from the solution with pure chloroform showed solid-wall pore structure. In contrast, nano-fibrous membranes were fabricated from the solution with pure 1,4-dioxane. In case of mixed solvents, the scaffold membranes showed various structures with changing composition of the solvents. When 1,4-dioxane content was lower than 20 wt% in the solvent, scaffold membrane showed solid-wall pore structure. When the content was 20 wt%, scaffold membranes with macropores with the maximum size of $100{\mu}m$ was obtained. In the concentration range of 1,4-dioxane over 25 wt%, the scaffold membranes showed nano-fibrous structures. In this range, the fibers showed different diameters with changing composition of the solvent. The minimum fiber diameter was about $15{\mu}m$, when 1,4-dioxane composition was 80 wt%. These results indicate that the composition of the solvent showed a significant effect on the structure of scaffold membrane.

• Proceedings of the Korean Fiber Society Conference
• /
• 1998.04a
• /
• pp.156-159
• /
• 1998

토목섬유는 목적에 따라 보강, 필터, 차수, 분리등의 기능으로 널리 사용되고 있으며 최근에는 한가지 기능을 강화하거나 다기능성을 부여하기 위해 복합화한 재료들이 사용되고 있다. 현재 토목섬유는 여러종류의 관련제품이 개발되어 상품화되고 있으나 널리 사용되고 있는 품목은 가정용ㆍ산업용 폐기물 매립시 발생되는 침출수 차단 목적과 연약지반의 지지력 보강, 부등침하방지에 의한 지반보호, 흙 댐, 터널 건설 등에 이용되는 지오멤브레인과 세립토ㆍ자갈ㆍ돌덩어리ㆍ블럭등의 혼합을 막아주는 분리기능, 자체의 인장강도에 의해 흙 구조 물의 안정성을 증가시키는 보호기능을 갖는 지오텍스타일이 있다.(중략)

• Proceedings of the Membrane Society of Korea Conference
• /
• 1995.04a
• /
• pp.48-49
• /
• 1995

금년에 고도화 사회의 진전을 배경으로 여러분야에서 섬유고분자재료에 대하여 보다 기능성이 요구되고 있다. 그 중에서도 가장 중요한 기증중의 하나인 감성과 정서, 쾌적 기능의 요구와 더불어 기능성 물질의 합성과 추출, 섬유에의 복합화 기능에 대하여 활발한 연구가 진행되고 있다. 기능성 물질의 섬유에의 복합화 가공은 섬유재료와 여러 공정 조건의 복합적 요소에 의하여 좌우되며 기능성 물질의 흡착, 포괄방법에서 일반적으로 흡진, 혼합방사, microcapsule에 의한 봉입처리를 후가공법으로 행해오고 있고 특히 기능성 물질의 안정적 측면에서 microcapsule에 의한 기능성 부여에 대한 연구가 특히 주목을 받고 있다.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.11a
• /
• pp.147-148
• /
• 2017

In this study, the tensile properties of mono and hybrid fiber reinforced cement-based composite according to fiber blending ratio under the high strain rate was evaluated. Experimental results, the HSF1.5PVA0.5 shown the highest tensile strength because the PVA fiber suppressed the micro cracks in the matrix around the hooked steel fiber and improved the pull-out resistance of hooked steel fiber. Thus, DIF of strain capacity and fracture toughness of HSF1.5PVA were greatly improved. Also, the fracture toughness was greatly improved because the tensile stress was slowly decreased after the peak stress by improvement of the pull-out resistance of hooked steel fiber at strain rate 101/s.

• Journal of the Korean Geotechnical Society
• /
• v.31 no.3
• /
• pp.5-16
• /
• 2015

The characteristics of tensile strength of fiber-reinforced grouting (cement paste) injected into rocks or soils were studied. A tensile strength of such materials utilized in civil engineering has been commonly tested by an indirect splitting tensile test (Brazilian test). In this study, a direct tensile testing method was developed with built-in cylinder inside a cylindrical specimen with 15 cm in diameter and 30 cm in height. The testing specimen was prepared with 0%, 0.5%, or 1% (by weight) of a PVA or steel fiber reinforced mortar. A specimen with 5 cm in diameter and 10 cm in height was also prepared and tested for the splitting tensile test. Each specimen was air cured for 7 days or 28 days before testing. The tensile strength of built-in cylinder test showed 96%-290% higher than that of splitting tensile test. The 3D finite element analyses on these tensile tests showed that the tensile strength from built-in cylinder test had was 3 times higher than that of splitting tensile test. It is similar to experimental result. As an amount of fiber increased from 0% to 1%, its tensile strength increased by 119%-190% or 23%-131% for 7 days or 28 days-cured specimens, respectively. As a curing period increased from 7 days to 28 days, its strength decreased. Most specimens reinforced with PVA fiber showed tensile strength 14%-38% higher than that of steel fiber reinforced specimens.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.6
• /
• pp.98-105
• /
• 2017

In this study, the fiber blending ratio and strain rate effect on the tensile behavior of hybrid fiber reinforced cement composite was evaluated. Hooked steel fiber and polyvinyl alcohol fiber were used for reinforcing fiber. The fiber blending ratio of HSF+PVA were 1.5+0.5, 1.0+1.0 and 0.5+1.5vol.%. As a results, the tensile strength, strain capacity and fracture toughness of the hooked steel fiber reinforced cement composites were improved by the increase of the bond strength of the fiber and the matrix according to increase of strain rate. However, the tensile stress sharply decreased after the peak stress because of the decrease in the number of straightened pull-out fibers by micro cracks in the matrix around hooked steel fiber. On the other hand, PVA fiber showed cut-off fracture at strain rate $10^{-6}/s$ with multiple cracks. However, at the strain rate $10^1/s$, the multiple cracks and strain capacity were decreased because of the pull-out fracture of PVA fiber. The HSF1.5PVA0.5 shown the highest tensile strength because the PVA fiber suppressed the micro cracks in the matrix around the hooked steel fiber and improved the pull-out resistance of hooked steel fiber. Thus, DIF of strain capacity and fracture toughness of HSF1.5PVA were greatly improved. In addition, the synergistic response of fracture toughness was positive because the tensile stress was slowly decreased after the peak stress by improvement of the pull-out resistance of hooked steel fiber at strain rate $10^1/s$.

• Microbiology and Biotechnology Letters
• /
• v.31 no.3
• /
• pp.257-263
• /
• 2003

The cellulases production in solid state fermentation (SSF) of Trichoderma harzianum FJ1 with high cellulases productivity using cellulosic wastes was investigated. Physical and chemical conditions of the fermentation, such as moisture content, initial pH, and composition of mixed substrate (wine waste, rice straw, and soybean flour) on FPase (Filter paper activity) production were examined. The enzyme production was optimized in the conditions of moisture content of 70%, pH 5.0, 3$0^{\circ}C$, and 1:1:1 composition of mixed substrate containing wine waste, rice straw, and soybean flour. The highest activities of FPA, CMCase, Xylanase, $\beta$-glucosidase, and Avicelase in the optimized culture conditions were 15.2, 69.1, 83.9, 29.2, and 4.2 unit/g-SDW in 5 day cultivation, respectively. Economical and efficient production of cellulolytic enzymes by T harzianum FJ1 using cellulosic wastes in solid state fermentation will contribute to the biological saccharification of cellulosic wastes with enormous potential resource value in future.