• Journal of Hydrogen and New Energy
• /
• v.18 no.3
• /
• pp.275-283
• /
• 2007

본 논문은 세관(ID<7 mm) 내 R-22와 R-134a의 증발 열전달과 유동양식에 대한 실험적 연구이다. R-22와 R-134a의 유동양식을 관찰하기 위해 내경 2와 8 mm의 파이렉스 튜브를 사용하였고, 열전달 계수는 내경 1.77, 3.35, 5.35 mm의 수평 평활동관에 대해서 측정하였다. 증발 유동양식에서 내경 2 mm의 환상류 영역이 내경 8 mm에 비해 저건도 영역에서 발생하는 것을 확인할 수 있었고, 내경 2 mm의 유동양식은 Mandhane의 선도와 많은 오차를 보였다. 세관(ID<7 mm) 내 증발 열전달 계수는 종래의 대구경관(ID>7 mm)에 비해 관직경에 대한 영향이 많이 나타나는 것을 알 수 있었다. 내경 1.77 mm의 열전달 계수는 내경 3.36 mm와 5.35 mm에 비해서 20내지 30% 정도 높은 것을 나타났다. 또한 종래의 열전달 상관식(Shah's, Jung's, Kandlikar's and Oh-Katsuda's correlation)과 비교한 결과, 실험 데이터는 상관식과 많은 이탈 정도를 보였다. 따라서 실험데이타를 기초로 세관내 R-22와 R-134a에 적용할 수 있는 증발 열전달 상관식을 새로이 제안하였다.

• Journal of Energy Engineering
• /
• v.7 no.1
• /
• pp.44-56
• /
• 1998

Separate heat pipe exchanger is considered as the high thermal transportation equipment, because evaporator and condenser are separately positioned in the long distance. Its characteristics are that the working fluid is circulated naturally by the position height of two exchangers. But the operating characteristics are restricted by the temperature of hot and cold fluid, flow pattern and diameter of vapor line, etc. in this study, the vapor pressure and the minimum height of two exchangers are studied about the factors restricting the operating characteristics.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.28 no.8
• /
• pp.337-342
• /
• 2016

A marine SCR System is emerging as an alternative to comply with NOx Tier III Emission standards, a restriction on greenhouse gas from vessels implemented by the International Maritime Organization. The system is greatly affected by the uniformity of the fluid flowing into the catalyst, so the performance of the catalyst of an SCR system needs to be guaranteed. This study conducted research on a mixed evaporator of an SCR system, which is one of the factors affecting the uniformity of the fluid. When the angle of the mixed evaporator is set to $90^{\circ}$, the fluid uniformity is at its highest at 83%, under the condition that the length of the mixed evaporator be 3.5 D. When the length was 3.5 D and less, the fluid uniformity had a tendency to improve relative to the case without a bent pipe. However, a longer mixed evaporator results in a more perfect liquidity development in the pipe with a liquidity distribution similar to the case where no curved pipe is formed in front of the catalyst. A lower angle for the mixed evaporator results in a lower flow uniformity, and a longer length of the mixed evaporator results in a lower difference in the flow uniformity caused by the angle. The flow uniformity can be improved by 6% with a mixed evaporator, which confirmed that all factors applied to an SCR system have a close relationship with the efficiency.

• 기계와재료
• /
• v.24 no.2
• /
• pp.62-71
• /
• 2012

세계적으로 NOx 저감 및 규제치의 강화로 인해 디젤기관에서 발생되는 NOx 제거에 대한 연구가 활발히 진행 중이며, 암모니아 환원제와 배출가스의 NOx를 혼합하여 촉매 존재하에서 NOx를 제거하는 시스템이 개발되고 있다. 대부분 암모니아를 보관성이 용의한 요소(Urea) 수용액으로 대체하여 배기관 내에 직접 요소수를 분사하며 요소 수용액이 고온의 배기가스에 의해 증발되어 암모니아를 환원시키며, 촉매를 통하여 탈질을 하는 Urea-SCR 시스템을 채택하고 있다. 따라서 촉매전단에서 요소수가 완전히 증발되고, 또한 촉매 입구에서 요소수의 증발로 인해 환원된 암모니아의 분포도 균일해야 함으로 Urea-SCR 시스템이 배기가스 유동 및 온도에 최적화된 분무특성을 가지는 분사제어 시스템을 제시하고자 한다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.1
• /
• pp.41-48
• /
• 2014

A urea-SCR system suffers from some issues associated with the ammonia slip phenomenon, which mainly occurs because of the shortage of evaporation and thermolysis time, and this makes it difficult to achieve an uniform distribution of injected urea. A numerical study was therefore performed by changing such various parameters as installed injector angle and application and angle of mixer to enhance evaporation and the mixing of urea water solution with exhaust gases. As a result, various parameters were found to affect the evaporation and mixing characteristics between exhaust gas and urea water solution, and their optimization is required. Finally, useful guidelines were suggested to achieve the optimum design of a urea-SCR injection system for improving the DeNOx performance and reducing ammonia slip.

• Proceedings of the Korean Society for Emotion and Sensibility Conference
• /
• 2001.11a
• /
• pp.208-210
• /
• 2001

본 연구에서는 운전자의 피로감을 경감시킬 수 있는 자동차용 향 발생장치를 개발하였다. 본 시스템은 공기 압력차에 의해 휘발된 향을 산소와 혼합 시켜 외부로 분사하는 증발 확산 방식을 채택하였다. 또한 3-Port Solenoid Valve를 이용하여 산소만 공급할 수 있도록 또는 산소와 향을 동시에 공급할 수 있도록 두 가지의 분출 경로가 가능하도록 제작하였고 향이 분사되는 배관 앞에 체크 밸브(역류방지기)를 장착하여 한 방향으로만 향이 분출되도록 하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.6
• /
• pp.27-36
• /
• 2018

A significant amount of studies were performed on evaporation heat transfer and pressure drop in microfin tubes. Most studies, however, focused on the refrigerants used in air-conditioners or heat pumps, and very limited information is available on R-404A, which is used in low temperature refrigeration. In this study, the evaporation heat transfer and pressure drop characteristics of R-404A in a 9.5 mm O.D. microfin tube were investigated for the mass flux range from $80kg/m^2s$ and $200kg/m^2s$. A smooth tube of the same outer dimeter was also tested for comparison. The results showed that the heat transfer enhancement ratio of the microfin tube increased with increasing mass flux and the heat flux decreased. The relative contribution of the convective heat transfer and the heat flux on total heat transfer was attributed to the observed trend. The pressure drops of the microfin tube were slightly (maximum 28%) larger than those of the smooth tube. Existing correlations do not adequately predict the measured heat transfer coefficients of pressure drops, probably due to the test range of the present study, which is outside of the existing correlations.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1997.10a
• /
• pp.7-11
• /
• 1997

직경 3.5 cm, 길이 1.5 m 의 석영관 내에서 염화제1철 증기를 수소로 환원하여 철 초미립자를 제조하였다. 염화제1철의 증발조건, 염화제1철 증기와 수소의 혼합방법, 반응물의 예비가열온도, 반응온도, 염하제1철의 농도, 반응기내 체류시간이 생성된 철 입자의 크기 및 크기분포에 미치는 영향을 조사하였다. 철 입자의 평균직경은 40-88 cm 이고, 기하표준편차는 1.4 정도로 나타났다. 철 입자들은 자기적 성질에 의해 서로 연결되어 체인을 형성하였으며, 전자회절분석 결과 단결정이었다. 평균입경 55nm 철 입자들의 항자력은 900 Oe, 포화자화값은 130 emu/g 이었다.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.11 no.6
• /
• pp.912-920
• /
• 1999

The forced convective boiling heat transfer coefficients of R-407C were measured inside a horizontal tube 6.0mm I.D. and 4.0m long. The heat transfer coefficients increased according to an increase in heat flux at constant mass flux. Because nucleation was completely suppressed in the two-phase flow region with high quality, heat transfer coefficients in forced convective evaporation were higher than those in nucleate boiling region. Average heat transfer coefficients of R-407C were about 30 percent lower than the pure refrigerant correlation, due to mass transfer resistance at the gas-liquid interface. However, the total experimental data shows an agreement with the predicted data for ternary refrigerant mixtures with a mean deviation of 30%.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.1
• /
• pp.72-83
• /
• 2017

A thermo-fluid dynamic analysis was performed through the numerical simulation of a missile canister. Calculation was made in a fixed analytical volume and fully evaporated water was used as a coolant. To analyze the interaction among the hot gas, coolant, and mixture flow, Realizable $k-{\varepsilon}$ turbulence and VOF(Volume Of Fluid) model were chosen and parametric study was performed with the change of coolant flow rate. It could be found that the pressure on the canister top nonlinearly increased with the increase of coolant flow rate. Temperature and coolant distribution were closely related to the flow behavior in canister. Temperature on the canister bottom indicated a decrease being proportional to coolant flow rate in early times but after a specific time, the temperature increased with the tendency being reversed. In addition, the early part of temperature showed a fluctuating phenomenon because of the overall circulatory flow of mixture gas.