• Journal of the Korean Chemical Society
• /
• v.44 no.5
• /
• pp.410-414
• /
• 2000

The feasibility of near infrared spectroscopy (NIRS) for the evaluation of the compost pro-duced by composting swine excreta has been investigated. The analytes determined were total nitrogen, total phosphorus, organic matter,total carbon,moisture, Cu, $K_2O$ and $Na_2O$. The ranges of concentration of the cal-ibration samples obtained by the conventional chemical method for each component were 1.30-2.75%, 1.45-4.86%, 7.36-81.5%, 23.0-41.1%, 4.2 the coefficient of variation was 4.38, 5.5, 3.2, 1.5, 10.9, 10.6 and 11.9% for total nitrogen, total phosphorus, organic matter, total carbon, moisture, Cu, $K_2O$ and $Na_2O$,respectively. The overall results showed that NlRS can be used for a non-destructive and rapid determination of the analytes to evaluate the quality of compost samples.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.57-60
• /
• 2008

Maglev is a system that a train runs levitated above a rail. Therefore it is very important to maintain a constant levitation gap for achieving serviceability and ride comfort. This study is a cooperation research subject of the 3-1 subject, performance improvement of maglev track structures, of the Center for Urban Maglev Program in Korea, started in 2006. The aim of this study is development of rapid constructions of bridge superstructure for maglev. At present, precast deck is widely used because of its superiority to cast-in-place concrete on quality and the term of works. The research group suggested basic systems of maglev guideway with PSC-U type and trapezoidal open steel box type girder, and precast deck, cooperating with Korea Railroad Research Institute, the managing institute of the 3-1 subject. In this study, a mock-up consisted of girders, decks and rail was fabricated and test was performed for constructability, serviceability and maintenance evaluation of PSC U-type girder, precast deck, and new guide rail system.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.1001-1004
• /
• 2008

This study reviewed the results of utilization of insulation heat curing method using double layer bubble sheet in slab concrete and mass concrete in cold weather environment. First of all, when double layer bubble sheets are applied, it was shown that slab concrete was protected from early freezing by remaining between 6 and $10^{\circ}C$ even in case outside temperature drops $10^{\circ}C$ below zero until the 2nd day from piling, and in the case of mass concrete, with the maximum temperature difference between the center and surface less than $6^{\circ}C$, crack occurrence index was close to 2 and no hydration heat crack occurred by internal constraint. The insulation heat preservation curing method using the double bubble sheet applied in this field prevented early freezing owing to stable curing temperature management, deterring concrete strength development delay at low temperature, and obtained the needed strength. Also, it was proven that the method is highly effective and economic for cold weather concrete quality maintenance through curing cost reduction like construction period shortening and labor cost reduction, etc by reducing the process of temporary equipment installation and disassembling.

• Journal of the Korean Society for Railway
• /
• v.18 no.1
• /
• pp.33-42
• /
• 2015

The vertical static stiffness of rail pads or baseplate pads, which are important components in rail fastening systems for track safety, is a key factor to determine the total track stiffness and a guideline of quality control in the manufacturing process. The vertical static stiffness can be checked by laboratory testing: test methods are EN 13146-9 and KRS TR 0014, which are widely used in the railway field. In this paper, to correct some problems, namely the preloading step, the unloading level, and the holding time in the loading program in the vertical static stiffness test of EN 13146-9 and KRS TR 0014, domestic and foreign test standards of pads were analyzed and then certain schemes for a vertical static stiffness test were proposed. To assess the reliability of the proposed schemes, the vertical static stiffness tests were performed with 4 pads and the validity of the test results was estimated.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.25 no.3
• /
• pp.249-255
• /
• 2007

The building of spatial database such as digital maps has been extensively achieved as a base of geographic information system. However, in the GIS system built by the organizations including local autonomous entities, there are some problems technically and systematically for a promptly updating of GIS DB. This research is to develop the object-oriented database updating system to efficiently update the spatial data at any time for a small area. It could be managed the history of spatial database such as creation, modification and deletion at a object level using the UFID of spatial data. This system could help to modify or update the changed geographical features in an office or in-situ promptly. Finally, it could be made the efficient updating manner of geographic data and the assurance of newest database.

• Journal of the Korea Institute of Building Construction
• /
• v.18 no.3
• /
• pp.211-218
• /
• 2018

This study examined the reliability and revision necessity of concrete standard specifications based on the comparisons with test data obtained by using domestic artificial lightweight aggregates and the contents specified in different foreign specifications including ACI 211.2, ACI 213, ACI 301, JASS 5 and CEB-FIP. To achieve the continuous particle distribution of domestic fine lightweight aggregates, the partial addition of natural sand with the maximum size of 2.5mm was required. To control the segregation and excessive bleeding in the fresh lightweight concrete, the current limitations on the water-to-binder ratio and unit water content need to be modified using lower values. In particular, a rational mixture proportion approach of lightweight concrete needs to be established for the targeted requirements of initial slump, 28-day compressive strength, air content and dry unit weight. Ultimately, significant revision of the concrete standard specifications is required considering the characteristics of domestic artificial lightweight aggregates.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2017.10a
• /
• pp.270-273
• /
• 2017

Productivity through reduced defects in plastic injection molding and reduced cycle times is a long-standing need in the injection industry. In particular, productivity is very urgent for the domestic injection industry, which is caught between the pursuit of latecomers such as China and technological gap with Germany and Japan which will not be narrowed down. Through 30 years of research and experience in the domestic injection industry, we have found that controlling the surface temperature of injection molds is the key of quality control. There have been various attempts to utilize advanced control techniques such as PID control, but the productivity against leading companies in Germany and Japan is still insufficient. Using Approximation Algorithm - "Knapsack" and "Minimum Makespan Scheduling", We want to show how to efficiently control objects with periodic repetitive data patterns that are difficult to solve with PID control. In addition, We want to propose that the control by Approximation Algorithm is effective enough to improve the productivity of the product by analyzing the data extracted from actual injection site.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.6
• /
• pp.4322-4327
• /
• 2015

Improper backfill materials and compaction controls under pipelines have become one of the major causes of failure in many sewage pipeline systems. A study on backfill materials and compaction controls has been considered for a long time. However, structural supporters under the pipe were recently concerned because of pipeline repair and maintenance. This paper presents a prefabricated plastic foundation for supporting a sewage pipe system and increasing the performance function of the pipes. Several analytical models for the plastic foundations were investigated using finite-element program, ABAQUS, for checking safety. Comparing with the results of analyses, some of economic design sections based on the sizes of pipe diameters, 600mm, 700 and 600mm, were evaluated. These results could be applied to a pipeline system with a prefabricated plastic foundation with respect to pipe diameters and buried depths.

• Journal of Korean Society of Steel Construction
• /
• v.19 no.5
• /
• pp.527-537
• /
• 2007

The main girders and cross-beams of an H-beam bridge consisted of factory-made H-beams, providing better conditions for quality control. Also, on-site fabrication works can be minimized and most of the stiffeners can be omitted, enabling simple and economic construction. In this study, the effect of the Multi-Stepwise TPSM (M-TPSM) on improving the maximum span length and section efficiency is analyzed. Compared to a 30-m-long, five-girder conventional plate girder bridge, structural analysis results showed that 50.7~55.1% of the girder height and 24.1~26.2% of the self-weight may be reduced by the application of M-TPSM to a five-girder H-beam bridge constructed with H-$900{\times}300$beams. In case of conventional H-beam bridges without M-TPSM, it was found that seven girders are required for a similar level of load-carrying capacity. Therefore, it is concluded that by the application of the M-TPSM, the H-beam bridge would become one of most cost-competitive options for short- and medium-span bridges.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2012.05a
• /
• pp.712-712
• /
• 2012

하 폐수 처리방류수를 물리적, 화학적 그리고 생물학적 기술을 이용하여 처리한 후 재활용수로 이용하고자 하는 새로운 노력들이 진행되고 있지만 국내의 경우 방류수 재활용 기술과 처리수의 재이용에 대한 평가기술이 선진국에 비해 초기 단계에 있어 이 분야에 대한 적극적인 기술개발이 요구된다. 막 분리 기술을 이용한 처리 수는 소독 등의 추가적인 처리 없이 살수용수나 수경용수로 이용이 가능하며, 잔류염소를 유지시킬 경우 화장실 세정용수로의 이용도 가능하며, 또한 후처리 기술을 조합하면 고급 공업용수 등으로 사용가능하므로 선진기술로서 수요조건에 맞게 전 후 처리를 조합한 수요자 맞춤형 재이용수 공정기술을 개발할 필요가 있다. 이에 효율적인 하 폐수 재이용을 이용하여 농업용수(축산 음용수, 첨단 수출원예용수, 첨단 농업용수, 농산업 클러스터 복합 곡물 용수), 원예용수(원예단지), 공업용수 등의 다양한 용도에 활용 가능한 수요자 맞춤형 모듈 및 공정 개발을 수행하였다. 개발된 공정은 AOP 및 막 세정 시스템을 이용한 새로운 공정으로, AOP 시스템은 전기 이온 모듈을 통해 OH 라디칼을 생성 및 염분 제거 효율을 극대화 하여 오염 물질을 산화시키는 공정이며, FDA 시스템은 탁도가 높은 원수가 과다 유입 될 경우 후단 여과 막의 부하를 줄이는 역할을 하며, 부유 물질을 여과 시킨다. 막 세정 시스템은 미세 입자를 구성된 기포를 이용하여 눈에 보이지 않는 곳 까지 세척하며, 살균 작용을 하며, 분리 막의 성능을 증대 시킨다. 이어 UF 분리 막 시스템은 원수의 미세불순물, 박테리아, 스케일 물질 등을 제거하며, NF 시스템을 통하여 미립자, 박테리아 유기 화합물 및 2가 염 제거를 하여 재이용수를 생산하는 공정을 개발하였다. 개발된 수요자 맞춤형 공정은 하수 재이용 기술의 이용 목적 및 수요자별로 맞춤형으로 운영이 가능하며, 개발된 세척 기술은 분리 막 세정 유지관리비 및 에너지를 저감 할 수 있으며, 현장 적용의 실증화 과정을 거쳐 공정 기술을 신뢰도를 향상하고, 보유 기술을 수요자 맞춤형으로 업그레이드함으로써 기술의 경쟁력 및 고품질의 하수 재이용 기술의 새로운 방향을 제시 할 수 있을 것으로 판단된다.