• Computational Structural Engineering
• /
• v.10 no.4
• /
• pp.165-175
• /
• 1997

In this paper, the stress, buckling and vibration analyses have been performed for several case with the spot weld stiffened rear side frame, the unstiffened rear side frame and the dual thickness laser weld rear side frame. For stress and vibration analyses, the clamped boundary condition with spring supports are used. But for the buckling analyses, the both ends simply supported boundary conditions are used. For the nummerical analyses, ANSYS 5.0 code is adopted. Maximum stress of the spot weld stiffened rear side frame occurs in the main frame and is 80.9 MPa. Maximum strain is 501 .mu.. The maximum stress of the dual thickness laser weld rear side frame of 1.8mm thickness structure is equal with the stress of spot weld stiffened frame. The weight of dual thickness laser weld frame can be reduced about 17.2%. For the stiffened spot weld rear side frame with both ends simply supported boundary conditon, the bucking load is 52.54 kN. When the thickness of the dual thickness laser weld rear side frame become 1.9mm thickness structure, the buckling load of the stiffenerd rear side frame is equal to that of dual thickness laser weld frame. The reduction of the structure weight is about 5%. The fundamental natural frequency of the stiffened spot weld rear side frame for bending mode is 163.6 Hz and that of the dual thickness laser weld rear side frame is 179.8 Hz.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2006.06a
• /
• pp.31-32
• /
• 2006

본 논문은 중형엔진 조립과정에서 실린더 프레임 회전 작업에 사용하는 지그의 구조해석을 수행한 후, 지그의 안전성을 검토하고 지그의 경량화를 통하여 실용적인 지그 설계안을 제안하였다. 현장 작업자가 들 수 있는 최대 무게를 넘는 지그를 구조해석 모델로 선정한 후, 해석모델은 지그, 실린더 프레임, 볼트, 너트, 샤클 핀을 3차원 입체요소로 구성하고 ABAQUS/Standard를 사용하여 재료 비선형 및 접촉을 고려한 구조해석을 수행하였다. 구조최적화를 위하여 응력이 상대적으로 낮은 부위와 작업성을 고려하여 설계변수를 선정하고, 실험계획법의 직교배열표를 활용하여 설계변수에 대한 각 부위의 민감도와 경량화 모델을 도출하였다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.20 no.5
• /
• pp.573-580
• /
• 2007

This paper presents the numerical estimation of the fatigue life for the frame box's welded parts of the marine vessel engine S60MC-C. The time-variations of the effective stresses at the critical points during a piston cycle are computed through the finite element analysis, by applying the dynamic loadings that were analytically derived in the previous paper. The fatigue lives of the welded parts are estimated by making use of the hot-spot stress extrapolation and the Palmgren-miner cumulative damage rule.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.11
• /
• pp.1507-1514
• /
• 2011

Injection molding is the most commonly used process that uses plastic material. Today, the uses of plastic material are continuously increasing, and the range of application is also being extended by the development of novel materials. An inline skate consists of 4 components: the boot, frame, wheel and brake. Among these components, the frame is the most critical. The injection formability for a variety of injection materials for inline skate frames was studied. We also studied the injection formability of the product for various sizes of the runner and gate. In this study, injection molding analysis was performed using MOLDFLOW, and structural analysis was performed using ANSYS.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.4
• /
• pp.539-544
• /
• 2006

This study is to apply a modal analysis for a frame and roller of a treadmaill machine. A finite element model was developed to compute natural frequencies of a frame and a roller. This analysis were performed under several different conditions such as weight, boundary, and maxium stress/strain conditions.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.7
• /
• pp.945-951
• /
• 2013

This study evaluated the fatigue strength of the bogie frame of an urban maglev train through fatigue analysis, cumulative damage, and fatigue tests based on a proposed fatigue evaluation method. The results of FEM analysis in which various load combinations were adopted showed that all data were under the fatigue limit of a butt welded joint made of A6005 in a Goodman diagram. The cumulative fatigue damage was calculated at the highest level from a bolt connecting the area of the electromagnetic pole in the casting block; however, the total sum was evaluated as D=0.808 based on $1{\times}10^7$ cycles, which indicates that it did not exceed the failure criteria. In addition, the results of the fatigue testshowed that there was no crack at any position in the bogie frame, which corresponded to the results of fatigue analyses.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.33 no.4
• /
• pp.209-216
• /
• 2020

In this paper, parametric structural analysis is presented utilizing the co-rotational(CR) shell analysis utilizing EDISON. CR shell analysis shows faster convergence than the commercial software, NASTRAN, does. The 1st natural frequency of the rear frame is obtained, which is close to that of the engine during high speed cruise. Three cases under two design variables are presented and analyzed. Gusset is shown to be more effective among those which feature the same weight change. The results presented in this paper will be applicable for further researches to improve the durability of a motorcycle rear frame.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.4
• /
• pp.419-425
• /
• 2014

This study applied finite element analysis (FEA) to the body frame of the 200-meter class multi-legged subsea walking robot known as Crabster (CR200). The body frame of the CR200 is modeled after the ribcage of a human so that it can disperse applied external loads. It is made of carbon-fiber-reinforced plastic (CFRP). Therefore, the frame is lighter and stronger than it would be if it were made of other conventional materials. In order to perform FEA for the CFRP body frame, we applied the material properties of the CFRP as obtained from a specimen test to an FE model of CFRP frame. Finally, we performed FEA with respect to the load conditions encountered when the robot is launched into and recovered from the sea. Also, we performed FEA for the frame, assuming that it was fabricated using a conventional material, in order to compare its characteristics with CFRP.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.1
• /
• pp.27-31
• /
• 2014

As research development of seat frame is being studied actively, the total deformation of seat frame made of high tension steel plate(HTSP) is examined in this study. The seat frame made of SPFC 980 t=2mm with HTSP is tested to obtain total deformation through repeated fatigue durability tester and total deformation is analyzed by simulation under the same condition as experiment. After analyzing by comparing the results of experiment and analysis, structural stabilities of seat frame models with SPFC 780 t=2mm and SPFC 780 t=1.5mm are investigated by FEM analysis on the basis of these results. And it is considered that which model is more suitable at commercial use can be found through this study result.

• Journal of Korean Society of Steel Construction
• /
• v.28 no.6
• /
• pp.383-394
• /
• 2016

This study is intended to predict the seismic behavior of the down-scaled 3-story steel frame structures subjected to the real ground motion, and evaluate their structural damage through advanced finite element (FE) analysis results. The FE frame models are designed by considering the effect of the soft story. In addition, the effect of structural asymmetry is also taken into consideration during the nonlinear dynamic analyses. After observing the analysis results, it is reconfirmed that the damage of the steel frame building under the ground motion should be governed by the soft story column rather than the structural mass asymmetry.