• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2003년도 학술대회논문집
• /
• pp.279-281
• /
• 2003

We analysed the operating properties of resistive type superconducting fault current limiters (SFCLs) based on YBCO thin films with a single line-to-ground fault. When a single line-to-ground fault occurred, the short circuit current of a fault phase increased up to about 6 times of transport currents immediately after the fault instant and was effectively limited to the designed current level within 2 ms by the resistance development of the SFCL. The fault currents of the sound phases almost did not change because of their direct grounding system. The unsymmetrical rates of a fault phase were distributed from 6.4 to 1.4. It was found that the unsymmetrical rates of currents were noticeably improved within one cycle after the fault instant. We calculated the zero phase currents for a single line-to-ground fault using the symmetrical component analysis. The positive sequence resistance was reduced remarkably right after the fault but eventually approached the balanced positive resistance component prior to the system fault. This means that the system reaches almost the three-phase symmetrical state in about 60 ㎳ after the fault. The ground currents were almost 3 times of the zero phase mts since most of the fault currents flowed through the grounding line.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 A
• /
• pp.421-423
• /
• 2004

As power system grows more complex and power demands increase, the fault current tends to gradually increase. In the near future, the fault current will exceed a circuit breaker rating for some substations, which is an especially important issue in the Seoul metropolitan area because of its highly meshed configuration. Currently, the Korean power system is regulated by changing the 154kV system configuration from a loop connection to a radial system, by splitting the bus where load balance can be achieved, and by upgrading the circuit breaker rating. A development project applying 154kV Superconducting Fault Current Limiter(SFCL) to 154kV transmission systems is proceeding with implementation slated for after 2010. In this paper, the expected price of SFCL in order to assure the economic feasibility is evaluated comparing with upgrading cost of ciui.1 breakers. The results show that the SFCL should be developed under seven times of price of circuit breaker to be competitive against upgrading circuit breakers.

• 전기학회논문지
• /
• 제67권12호
• /
• pp.1587-1594
• /
• 2018

In south korea, the government make a plan to generate the 20% of the total electrical power as renewable source like wind generation and solar generation. This plan will accelerate the increase of fault current with power industry's growth. As the increase of fault current, the superconducting fault current limiter (SFCL) has been studied. In case that the SFCL is applied in power system, it can cause the overcurrent relay (OCR)'s trip delay because of the reduced fault current. In this paper, the overcurrent relay with voltage component was suggested to improve the OCR's trip delay caused by the SFCL and compensational constant was introduced to have the trip time similar to the trip time of case without the SFCL. For conforming the effect of the suggested OCR with voltage component, the PSCAD/EMTDC simulation modeling and analysis were conducted. Through the simulation, it was conformed that the trip delay could be improved by using the suggested OCR and compensational constant.

• 한국초전도ㆍ저온공학회논문지
• /
• 제9권3호
• /
• pp.26-31
• /
• 2007

In recent years. YBCO coated conductor (CC) called as second generation HTS (high temperature superconducting) wire has been developed as a suitable material for resistive superconducting fault current limiter (SFCL). For designing the SFCL. the required length of superconducting wire is inverse proportional to the maximum temperature reached when a fault occurs. Since the required length strongly affects a manufacturing cost, it is the most important parameter to determine the maximum temperature reached. It is necessary to observe the repetitive over-current characteristics of HTS wire. This paper attempts to measure the variation of critical current of YBCO CC after repetitive over-current pulse. No degradation of the critical current of CC sample was observed by applying 100 times over-current pulse which makes temperature above 400 K after 100ms. This study can be useful in designing optimally resistive SFCL employing YBCO CC. The maximum permissible temperature can be set to 400K. so wire length could be reduced by 30% compared in case of 300K-criterion.

• 한국초전도ㆍ저온공학회논문지
• /
• 제11권3호
• /
• pp.35-39
• /
• 2009

The study for a protective relay system is one of the important technical issues on the power system application of Superconducting Fault Current Limiter (SFCL). We used Real Time Digital Simulator(RTDS) to study the true interaction of the protection system with the power system. RTDS modeling of SFCL is necessary to the detailed protective relay tests. In this paper, we developed an analysis model using RTDS for studying the transient behavior of 22.9kV SFCL and carried out closed-loop testing of protective relays in distribution power system with the developed SFCL model. The SFCL model has the operation mechanism of 22.9kV hybrid SFCL being developed by LSIS and KEPRI in Korea. The parameters of the model are based on the test data of the real SFCL. Power system planners and operators can solve the expected problems in power system application of SFCL using protective relay testing results.

• 한국초전도ㆍ저온공학회논문지
• /
• 제12권1호
• /
• pp.22-27
• /
• 2010

This paper analyzed bus voltage sag caused by recloser-fuse coordination in a power distribution system with SFCL. Generally, the recloser is installed to upstream of fuse to clear against both permanent and temporary faults appropriately, when the fault happened and to block expansion of the fault area. Furthermore, when the fault occurred, bus voltage sag is caused by increased fault currents. However, in a power distribution system with SFCL, the fault current could be decreased by the effect of the impedance value of the SFCL and place to install one as long as it could improve bus voltage sag. Therefore, to analyze the effect of the improvement of bus voltage sag caused by recloser-fuse coordination in a power distribution system with SFCL, we used PSCAD/EMTDC about a permanent fault at the place behind the fuse.

• 한국전기전자재료학회논문지
• /
• 제36권6호
• /
• pp.614-619
• /
• 2023

The fault current limiting characteristics of three-phase transformer type superconducting fault current limiter (SFCL), which consisted of three-phase primary and secondary windings wound on E-I iron core, one high-TC superconducting (HTSC) element connected with the secondary winding of one phase and another HTSC element connected in parallel with other two secondary windings of two phases, were analyzed. Unlike other three-phase transformer type SFCLs with three HTSC elements, three-phase transformer type SFCL using double quench has the merit to perform fault current limiting operation for three-phase ground faults with two HTSC elements. To verify its proper three-phase ground fault current limiting operation, three-phase ground faults such as single-line ground, double-line ground and triple-line ground faults were generated in three-phase simulated power system installed with three-phase transformer type SFCL using double quench. From analysis of its fault current limiting characteristics based on tested results, three-phase transformer type SFCL using double quench was shown to be effectively operated for all three-phase ground faults.

• 한국해양학회지:바다
• /
• 제5권4호
• /
• pp.305-319
• /
• 2000

동해 북동쪽에 위치한 홋카이도섬 서부해역에서 채취된 중력시추코아 GH98-1223의 45개 퇴적물 시료들로부터 휴면포자를 제외한 총 31속 50종 1아종의 규조류가 동정되었다. 최대 산출종은 Thalassionema nitzschioides로 전시료에서 29${\sim}$59%의 높은 산출빈도를 나타냈으며, 그 외에 비교적 개체 보존이 양호한 Denticulopsis seminae와 Pseudoeunotia doliolus를 비롯한 대부분의 종들은 평균 산출빈도가 5% 이내로 매우 낮게 나타났다 전 시료에서 한류종의 산출빈도가 난류종보다 상대적으로 우세하였으며, 수직분포는 각 종의 생태적 특성에 따라 차이가 있으나 대부분의 층준에서 난류종과 한류종의 산출빈도는 서로 상반되는 경향을 보였다. 대표적인 한류종인 D. seminae와 난류종으로 쿠로시오해류(Kuroshio Current)의 지류인 대마난류(Tsushima Warm Current)의 지시종인 P doliolus의 전체적인 변화양상은 뚜렷하게 상반되며, 이것은 규조온도지수(T$_d$)의 수직적인 변화와도 서로 일치한다. 규조온도지수는 150 cm깊이를 기준으로 코아의 상부에서는 평균 이상의 높은 수치를 나타내며 하부에서는 평균 이하의 낮은 수치를 나타내는데, 이러한 경향은 동해의 북부지역에 위치한 본 연구지역에 대마난류의 영향이 홀로세의 후빙기를 거치면서 점차적으로 증가된 것을 지시하고 있다. 또한, 하층부에서 규조온도지수는 지그재그형의 변화를 나타내는데 이는 규조류가 서식하는 해수의 환경이 불안정하였다는 것을 의미한다. 생산성과 용승의 정도를 지시하는 Chaetoceros resting spores는 5.3${\sim}$40% 정도의 산출빈도를 보이는데 , 최대값은 80 cm 보다 상층부에서 나타났다. 퇴적물의 생물 기원물질의 상대적인 양을 예측하는데 이용되는 Chaetoceros resting spores/Chaetoceroe vegetative cells도 80 cm 보다 상층에서는 높게 나타나 규조온도지수 분포와도 일치하는 경향을 보인다. 이상의 규조군집 분석 결과에 의하면, 홀로세의 후빙기동안 본 연구 지역인 동해 북동부에는 대마 난류의 유입이후 현재와 유사한 환경이 우세하게 발달했으나, 난류종 P. doliolus의 변화는 동해내에서 대마난류의 세기가 반복되었음을 지시하고 있다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권6호
• /
• pp.771-780
• /
• 2014

배열형(Array type)의 HF Radar를 임원항(Site A)과 후정리 해변(Site B)에 설치하여 동해연안에 대한 실시간 파랑과 해류를 관측하였다. 본 연구에 사용된 WERA (WavE RAdar)는 2000년 독일 Helzel사에서 개발된 것으로 24.525 MHz의 주파수 대역을 사용한다. 각 사이트는 4기의 송신기와 8기의 수신기로 구성되어 있는 8 채널 시스템이며, 현재 30분 주기로 관측하여 자료를 생성하고 있다. 파랑은 최대 약 25 km, 해류는 최대 약 50 km의 관측 범위를 나타내며, 150 kHz의 대역폭을 사용하여 1.5 km 간격의 격자 해상도를 갖는다. HF Radar를 이용하여 관측한 파랑 자료는 현장에서 관측한 파랑계 자료와 비교 검증을 하였으며, 해류 자료는 국립해양조사원에서 제공한 월별 동해평균표층 해류도와 해류흐름 패턴과 비교하였다. 파랑의 비교 자료들에 대한 회귀선과의 편차는 주성분 분석(Principle Component Analysis)으로 계산하였고, 그 결과로 상관관계 0.86와 RMSD 0.186을 보였다. 또한 동해연안의 해수유동에 대한 장기간의 변화를 분석해본 결과 8월과 9월의 연안에서는 북한한류가 남쪽방향으로, 외해에서는 동한난류가 북쪽방향으로 흐르는 흐름이 나타났다.

• 전기학회논문지
• /
• 제57권3호
• /
• pp.398-402
• /
• 2008

Recently, the development of superconducting fault current limiters (SFCLs) has been required as power demands increase in the power system. A distribution-level prototype resistive SFCL using coated conductor (CC) has been developed by Hyundai Heavy Industries Co., Ltd. and Yonsei University for the first time in the world. The ratings of the SFCL are 13.2kV/630A at normal operating condition. A novel non-inductive winding method is used in fabricating coils so there is almost zero impedance during normal operation. The distribution SFCL is cooled by sub-cooled liquid nitrogen $(LN_2)$ of 65K and 3 bar to enhance cryo-dielectric performance, critical current density, and thermal conductivity. In order to make reliable operation of an SFCL in real power systems, we monitored and controled its operation conditions by using supervisory control and data acquisition (SCADA) method. Thus, a monitoring system for the SFCL employing information technology (IT) is proposed and developed to be on the lookout for the operation conditions such as inside temperature, inside pressure, $LN_2$ level, voltage and current. Since operation temperature should be kept constant, bang-bang control for temperature feedback with a heater attached to the cold head of cryo-cooler is applied to the system. Short-circuit tests with prospective fault current of 10kA and AC dielectric withstand voltage tests up to 143kV for 1 minute were successfully performed at Korea Electrotechnology Research Institute. This paper deals with the development of a distribution level SFCL and its monitoring system for reliable operation.