• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.25 no.4
• /
• pp.301-305
• /
• 2012

In this work the mechanical behaviors of GaN nanowires are analyzed during tension, compression, and unloading deformations. The thermal conductivity of the nanowires at each deformed state is evaluated using an equilibrium Green-Kubo approach. Under tensile loading, the [0001]-oriented nanowires with hexagonal cross-sections undergo a phase transformation from wurtzite to a tetragonal structure. The phase transformation is not observed under compressive loading. The thermal conductivity decreases on going from compressive strains to tensile strains. The strain dependence of the thermal conductivity results from the relaxation time of phonon. A reverse transformation from the tetragonal structure to the wurtzite structure is observed during unloading. The thermal conductivities in the intermediate states are lower than the conductivity in the wurtzite structure at same strain. Such differences in the thermal conductivity between different atomic structures are mainly due to changes in the group velocity of phonon.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.10
• /
• pp.4642-4647
• /
• 2011

Solution for elastic foundation of plane strain state was derived by the application of variational method. Functions of the transverse distribution of the displacements for the analysis were chosen as linear functions. Loading conditions considered for the analysis were concentrated load and distributed load. Under the loading condition of the concentrated load, surface displacement was decreased drastically as the distance from the point of the loading increased. Under the loading condition of the distributed load, surface displacements were more uniformly distributed beneath the loading area when the ratio of the half of the loading width to the depth(B/H) of the compressible layer was greater. The surface displacement was more quickly converged from the edge of the loading area as the ratio(B/H) increased.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.3
• /
• pp.279-286
• /
• 2019

In this study, an experimental study on the tensile properties of steel fiber-reinforced ultra high strength concrete(UHSC) with a standard compressive strength of 180MPa was performed. Steel fibers with a volume ratio of 1% were mixed to prepare direct tensile strength specimens and prism specimens for the three-point bending test. The fabricated specimens were set up in the middle section of the specimen to induce cracks, and the test was carried out according to each evaluation method. First, the stress-strain curves were analyzed by performing direct tensile strength tests to investigate the behavior characteristics of concrete after cracking. In addition, the load-CMOD curve was obtained through the three-point bending test, and the inverse analysis was performed to evaluate the stress-strain curve. Tensile behavior characteristics of the direct tensile test and the three-point bending test of the indirect test were similar. In addition, the tensile stress-strain curve modeling presented in the SC structural design guidelines was performed, and the comparative analysis of the measured and predicted values was performed. When the material reduction factor of 1.0 was applied, the predicted value was similar to the measured value up to the strain of 0.02, but when the material reduction factor of 0.8 was applied, the predicted value was close to the lower limit of the measured value. In addition, when the strain was greater than 0.02, the predicted value by SC structural design guideline to underestimated the measured value.

• Magazine of the Korea Concrete Institute
• /
• v.3 no.4
• /
• pp.79-88
• /
• 1991

In this study, fracture tests were carried out in order to investigate the fracture behavior of SFRC(Steel Fiber Peinforced Concrete) with initial cracks. The relationships between loading. strain, mld-span deflections and CMOD(Crack Mouth Opening Displacement) of the beams were observed under the three point loading system. The effect of the fiber content and the initial crack ratio on the concrete fracture behavior were studied and the fracture toughness, the critical energy release ratio and the fracture energy were also calcul ated from the test results. From the test results, it was known that when the fiber contents are between 0.5% and 1.0%, and 1.5% the average fracture energy of SFRC specimens is about 7~10 times. and about 15 times better than that of the plam concrete specimens respectively.ively.

• Journal of the Korea Concrete Institute
• /
• v.25 no.1
• /
• pp.19-28
• /
• 2013

The longitudinal axial strain in the plastic hinge region of reinforced concrete (RC) columns influences on the structural behavior of RC structures subjected to reversed cyclic loading. This strain decreases the effective compressive strength of concrete and increases the lateral displacements between stories by causing the elongation of member length. This paper investigated the effects of the axial force on the elongation of a RC member by using a sectional analysis of RC members. The analytical and experimental results indicated that the axial force decreased the axial strain in the plastic hinge region of RC columns. In this study, a model was proposed to predict the axial strain of RC columns. The proposed model considering the effects of axial force ratio consisted of three path types ; Path 1-loading region, Path 2-unloading region, and Path 3-reversing cyclic loading region. The axal strains predicted by the proposed model were compared with the test results of RC columns with various axial force ratios, and agreed reasonably with the observed longitudinal strains.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.8 no.1
• /
• pp.39-45
• /
• 2008

The most important elements in flexible pavement design criteria are stress and strain distributions. To obtain reasonable stress and strain distributions in pavements, moving wheel loads must be applied to analyze the pavement responses. In this study, finite element analysis was used to identify the three-dimensional states using the vehicle load into a constant-position / time-variable load (25, 50 and 80km/hr). In an elastic system, the strain is the same in both longitudinal and transverse directions under a single wheel. However, the same is not necessary in a viscoelastic system. Test results showed that the maximum values between transverse and longitudinal strains the bottom of asphalt concrete base layers under 25km/hr were were about 40 percent.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.16 no.1
• /
• pp.99-109
• /
• 2012

This study aimed to develop a Structural Health Monitoring System for steel beams in the manner of suggesting and verifying a theoretical formula for displacement estimation using strain gauges, and estimating the loading points and magnitude. According to the results of this study, it was found that when a load of 160kN (56% of the yield load) was applied, the error rate of the deflection obtained with a strain gauge at the point of maximum deflection compared to the deflection measured with a displacement meter was within 2%, and that the estimates of the magnitude and points of load application also showed the error rate of not more than 1%. This suggests that the displacement and load of steel beams can be measured with strain gauges and further, it will enable more cost-effective sensor designing without displacement meter or load cell. The Structural Health Monitoring System program implemented in Lab VIEW gave graded warnings whenever the measured data exceeds the specified range (strength limit state, serviceability limit state, yield strain), and both the serviceability limit state and strength limit state could be simultaneously monitored with strain gauge alone.

• 대한치과교정학회:학술대회논문집
• /
• 1999.11a
• /
• pp.63-63
• /
• 1999

• The Journal of Korean Academy of Prosthodontics
• /
• v.47 no.2
• /
• pp.164-173
• /
• 2009

Purpose: The purpose of this study was to evaluate the effect of abutment material on screw-loosening before and after cyclic loading. Among the different materials of abutments, zirconia and metal abutment were used. Material and methods: Two types of implant systems: external butt joint(US II, Osstem Implant, Korea) and internal conical joint(GS II, Osstem Implant, Korea) were used. In each type, specimens were divided into two different kinds of abutments: zirconia and metal(n=5). The implant was rigidly held in a special holding to device ensure fixation. Abutment was connected to 30 Ncm with digital torque gauge, and was retightened in 30 Ncm after 10 minutes. The initial removal torque values were measured. The same specimens were tightened in 30 Ncm again and held in the cycling loading simulator(Instron, USA) according to ISO/FPIS 1480. Cycling loading tests were performed at loads 10 to 250 N, for 1 million cycles, at 14 Hz,(by subjecting sinusoidal wave from 10 to 250 N at a frequency of 14 Hz for 1 million cycles,) and then postload removal torque values were evaluated. Results: 1. In all samples, the removal values of abutment screw were lower than tightening torque values(30 Ncm), but the phenomenon of the screw loosening was not observed. 2. In both of the implant systems, initial and postload removal torque of zirconia abutment were significantly higher than those of metal abutment(P<.05). 3. In both of the implant systems, the difference in removal torque ratio between zirconia abutment and metal abutment was not significant(P>.05). 4. In metal abutments, the removal torque ratio of GS II system(internal conical joint system) was lower than that of US II system(external butt joint system)(P<.05). 5. In zirconia abutments, the difference in removal torque ratio between the two implant systems was not significant(P>.05). Conclusion: Zirconia abutment had a good screw joint stability in the condition of one million cycling loading.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.54 no.3
• /
• pp.159-168
• /
• 2012

본 연구에서는 해성 점성토에 대하여 반복 삼축시험을 실시하고 응력-변형률 관계 및 유효응력경로 특성 분석을 통해 동적 변형 및 강도 특성을 조사하였다. 시험에 사용된 시료는 일본 도쿠시마현의 코마츠시마 항 인근에서 채취된 점성토이며, 반복 삼축시험으로 동적 비배수 삼축시험, 동적 비배수 삼축시험 후 동적 삼축변형시험, 다단계 동적 비배수 삼축시험, 동적 삼축 변형시험 등 4종류의 시험을 수행하고, 시험 주파수로서 0.1 및 0.01 Hz을 적용하였다. 본 연구 결과 0.01 Hz로 수행된 동적 삼축시험 결과는 0.1 Hz로 수행된 삼축시험 결과보다 평균유효응력의 감소량이 크며, 반복 하중은 해성 점성토의 구조적 약화를 초래하고 초기 거동시 발생하는 간극수압과 밀접하게 관련이 있는 것으로 나타났다. 또한 미소변형률 영역에서 등가 탄성계수는 시험 횟수가 증가함에 따라 점차 감소하며, 감쇠비는 점차 증가하는 것으로 보아 변형계수는 반복 하중으로 인한 전단변형률의 축척에 따른 변형률 의존 거동에 관련하는 것으로 판단된다.