• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.5
• /
• pp.36-41
• /
• 2016

In this study, numerical analyses were used to investigate the performance of a coupling control method for the dynamic responses of adjacent buildings under multiple hazards. Numerical simulations were done using the earthquake loads of regions with strong seismicity in Los Angeles, California, and the wind loads in regions with strong winds in Charleston, North Carolina. The artificial earthquake and wind loads were made using SIMQKE and Kaimal Spectrum based on ASCE 7-10. Ten-story and twenty-story adjacent buildings were selected as example structures, and nonlinear hysteretic dampers were used to connect them. The Bouc-Wen model was used to model the nonlinear hysteretic dampers. The results show that the proposed control method could effectively reduce the dynamic responses, and the optimal control designs were different for each hazard.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.10 no.6
• /
• pp.87-94
• /
• 2006

Estimating moving vehicle loads is important in modeling design loads for bridge design and construction. The paper proposes a moving force identification algorithm using moment influence lines measured at multi-axes. Density estimation function was applied to estimate more than two wheel loads when estimated load values fluctuated severely. The algorithm has been examined through simulation studies on a simple-span plate-girder bridge. Influences of measurement noise and error in velocity on the identification results were investigated in the simulation study. Also, laboratory experiments were carried out to examine the algorithm. The load identification capability was dependent on the type and speed of moving loads, but the developed algorithm could identify loads within 10% error in maximum.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.23 no.5
• /
• pp.525-533
• /
• 2010

Direct time integration method such as Newmark method is numerically performed under the assumption that continuous load function such as constant amplitude load can be treated as a discontinuous load fuction. It is due that the load can be treated as a constant value at the given time period regardless of variation of load at the time increment interval. It means the numerical results should be accompanied by the error due to approximation of load fuction. In contrast, the load function is calculated by convolution integral for the given time interval at finite element equation based on Gurtin's variation equation. Therefore. precise numerical results can be obtained by Gurtin's method because of convolution integral for the continuous load fuction curve even at the variation of load function in the given time interval. In this study, we prove that Gurtin's method can be more suitable than Newmark method in the problem of constant amplitude loading, using the numerical results for the free end of the one-dimensional rod. This study also shows that Gurtin's method is more effective in constant amplitude loading than in constant loading. The accuracy and the validity are verified by comparison between the results of in-house FORTRAN code and ADINA, a commercial software supporting Newmark method.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.229-232
• /
• 2008

In rapid cycle construction, RC structure which is not cured fully can be loaded with construction load and this construction load can influence on the safety of construction and cracks on slabs. Therefore, to reduce the term of construction, the safety of construction and prevention of cracks should be assured against construction load. In the previous study, temperature load can significantly influence on the behavior of structure under construction. However, existing construction sequential analysis or design code do not consider temperature load reasonably. In the present study, through construction sequential analysis method using FE analysis, the behavior of structure under construction was analyzed according to temperature changes. According to the results of analysis, as the temperature falls, shoring load drops and the temperature rises, shoring load rises. These variations of shoring load can affect the safety of construction. Moment of slab goes up by fall in temperature. This increase of moment can cause cracks on the slab. Therefore to assure the safety on construction and prevent cracks on slabs, temperature load has to be considered reasonably in construction sequential analysis.

• International Journal of Highway Engineering
• /
• v.8 no.3 s.29
• /
• pp.143-153
• /
• 2006

The differences in the stress distribution and the critical stresses in concrete pavement systems were analyzed when the dual-wheel single-, tandem-, and tridem-axle loads were applied at the interior and the edge of the pavement. The effects of the concrete elastic modulus, slab thickness, foundation stiffness, and tire contact pressure were investigated. The stresses under the interior loads were calculated using the transformed field domain analysis and stresses under the edge loads were obtained using the finite element method. The critical stresses under the interior and the edge loads were compared with respect to various parameters and the equations to predict the ratio between the stresses under the edge and the interior loads were developed and verified. From this study, it was found that the trends of the changes in the critical concrete stresses under the interior and the edge loads were very similar and the critical stress locations under those loads were identical. The critical stress ratio, which was obtained by dividing the critical stress under the edge loads into that under the interior loads, decreased with increasing the number of axles. That ratio became larger as the concrete elastic modulus increased, the slab thickness increased, the foundation stiffness decreased, and the tire contact pressure increased.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.1
• /
• pp.9-14
• /
• 2017

In the present work, a mechanical performances under cyclic loading in RC (Reinforced Concrete) beams with normal steel and FRPH (Fiber Reinforced Plastic Hybrid) bar are investigated. For the work, RC beam members with $200{\times}200{\times}2175mm$ of geometry and 24 Mpa of design strength are prepared, and 4-point-bending tests are performed for evaluation of cracking, yielding, and ultimate loads. Through static loading test, 48.9kN and 36.0 kN of yielding loads are measured for normal RC and FRPH beam, respectively. They have almost same ultimate load of 50.0 kN. Typical tension hardening behavior is observed in FRPH beam, which is caused by the behavior of FRPH bar with tension hardening. In cyclic loading conditions, FRPH beam has more smaller crack width and scattered crack pattern, and it shows more elastic recovery than normal RC beam. The energy dissipation ratio in FRPH beam is 0.83, which is greater than 0.62 in normal RC beam and it shows more effective resistance to cyclic loadings.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.6D
• /
• pp.951-960
• /
• 2006

Structural pavement analysis considering lateral loads of moving vehicle was carried out in order to simulate passing vehicle loads under various interface conditions. To verify of existing multi-layer elastic analysis of layer interface effect parameters, this study compared outputs by using ABAQUS, a three dimensional finite element program and KENLAYER, multi-layer elastic analysis as vertical load was applied to the surface of asphalt pavements. Pavement performance depending on interface conditions was quantitatively evaluated and fundamental study of layer interface effect parameters was performed in this study. As results of the study, if only vertical loads of moving vehicle is applied, subdivision of either fully bonded or fully unbonded is enough to indicate interface effect parameters. On the other hand, when lateral loads are applied with vertical loads, pavement behavior and performance are greatly changed with respect to layer interface conditions. The thinner thickness of the asphalt layer is and the smaller elastic moduli of the asphalt layer is, the more pavement behavior is influenced by interface conditions. In addition, regression analysis equation analytically computing tensile strain which was considered thicknesses and elastic moduli of the asphalt layer and layer interface effect parameters at the bottom of the asphalt layer was presented using database from numerical analyses on national pavement model sections.

• The Journal of the Acoustical Society of Korea
• /
• v.16 no.4
• /
• pp.21-28
• /
• 1997

In this study, comparison between Harris-theoretical values and experimental data of load-deflection characteristics in bearing was made. The experiments are conducted under the conditions of the various radial loads and speed of shaft. In the case of non-defective ball bearing, the experimental data agreed well with the Harris-theoretical values for the small steady radial load but not for the large steady radial load. For the radial load bearing, the experimental results show that the stiffness of bearing at the single and multiple defective bearing are bigger in the radial defectiion than in the axial deflection. Load-deflection characteristics for the bearing defect part make it possible to detect the presence of a defect in bearing.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.16-16
• /
• 2017

국내 농업인구 감소 대비 식품소비량이 증가함에 따라 농가의 인력을 대체하고 다양한 작업이 가능하며 가격이 저렴한 국내 기계화 기술이 필요하다. 무동력 디스크해로우 작업기는 경운과 배토가 가능한 복합작업기로서 작업기를 구성하는 주요 구성품들은 필드작업에 의해 발생되는 하중에 구조적 강도와 신뢰성이 충분히 확보되어야 한다. 또한, 실제로 필드 작업 시 작업기에 걸리는 하중은 복합하중 형태로 전달되기 때문에 단순한 형태 하중에 비해 하중계측에 어려운 점이 있으므로 하중계측점의 선정이 매우 중요하다. 본 논문에서는 하중계측점을 선정하기 위하여 복합기의 주요 구성품인 치즐(chisel) 및 디스크해로우암(disk harrow arm)에 대하여 구조해석을 수행하였으며, 3축 방향의 단위하중 응력 계산결과로부터 load reconstruction을 위한 스트레인 게이지 위치를 선정하였다. 또한, 스트레인 게이지의 신호가 하중해석에 적절한 값이 되도록 기존의 형상을 수정하였다.

• Composites Research
• /
• v.13 no.1
• /
• pp.69-77
• /
• 2000

This paper presents a modified arc-length method for the nonlinear finite element analysis of a structure which is loaded in incremental and fixed forces, simultaneously. The main idea of the method is to separate the displacement term by the constant force from that by the incremental force. Presented method is applied to the nonlinear analysis of isotropic shell structures separately loaded by lateral pressure or compression, and shows the excellent agreement with previous results. As an illustrative example of the applicability of the present algorithm, a parametric study is performed on the nonlinear buckling analysis of composite cylindrical panels under the combined load of the incremented compression and the constant lateral pressure.