• The Bulletin of The Korean Astronomical Society
• /
• v.37 no.2
• /
• pp.153.1-153.1
• /
• 2012

조립 후 발사대로 이송된 추진기관(또는 발사체)는 지상시험 및 비행시험을 위한 충전을 하게 되는데, 추진제 및 고압가스 등 추진기관 구성품의 운용절차는 하드웨어의 설계 단계에서 그 개념이 수립되어야 한다. 다시 말해, 발사체 및 추진기관 설계 단계에서 연료와 산화제의 충전/배출, 시험 취소시의 운용절차 개념이 수립되어 있어야 추진기관 구성품들의 설계, 지상인터페이스 구성품의 설계에 그 내용이 반영될 수 있다. 따라서, 본 논문에서는 발사체 및 추진기관 운용와 관련된 일반적인 충전/배출 절차와 지연 또는 취소시의 작업절차의 주요개념을 다루었고, 추진기관 운용에 필요한 각종 지상설비에 요구되는 주요 기능을 검토하였다. 또한, 추진제 충전 이후 발사 대기시까지의 업무와 발사 전에 수행되어야 하는 추진기관 운용 업무(Pre-Launch Operation)도 다루었다. 특히 다단 발사체의 경우에는 운용과 관련된 준비 업무량이 단수에 비례하여 늘어나므로, 효율적으로 모든 시험 준비 업무를 마치기 위해, 지상에서의 추진기관 운용절차는 각 단별로 유기적으로 진행되어야 한다. 즉, 각 단별 하드웨어에 대한 사전 검사, 충전, 대기 등의 운용시간 설계 및 그 절차가 중요하다. 한국형 발사체 및 추진기관의 운용 개념설계를 수행하는데에는 기 확보된 운용기술을 활용하였다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.05a
• /
• pp.486-489
• /
• 2010

This paper describes a layered LDPC decoder which supports block length of 1,944 bits and code rate 1/2 for IEEE 802.11n WLAN standard. To reduce the hardware complexity, the min-sum algorithm and layered architecture is adopted. A novel memory reduction technique suitable for min-sum algorithm reduces memory size by 75% compared with conventional method. The designed processor has 200,400 gates and 19,400 bits memory, and it is verified by FPGA implementation. The estimated throughput is about 200 Mbps at 120 MHz clock by using Xilinx Virtex-4 FPGA device.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.9B
• /
• pp.914-922
• /
• 2009

In this paper, we propose a matrix based real-time pattern matching method, called MDPI, for real-time intrusion detection on several Gbps network traffic. Particularly, in order to minimize a kind of overhead caused by buffering, reordering, and reassembling under the circumstance where the incoming packet sequence is disrupted, MDPI adopts independent partial matching in the case dealing with pattern matching matrix. Consequently, we achieved the performance improvement of the amount of 61% and 50% with respect to TCAM method efficiency through several experiments where the average length of the Snort rule set was maintained as 9 bytes, and w=4 bytes and w=8bytes were assigned, respectively, Moreover, we observed the pattern scan speed of MDPI was 10.941Gbps and the consumption of hardware resource was 5.79LC/Char in the pattern classification of MDPI. This means that MDPI provides the optimal performance compared to hardware complexity. Therefore, by decreasing the hardware cost came from the increased TCAM memory efficiency, MDPI is proven the cost effective high performance intrusion detection technique.

• Nuclear Medicine and Molecular Imaging
• /
• v.42 no.2
• /
• pp.153-163
• /
• 2008

Medical imaging modalities to image either anatomical structure or functional processes have developed along somewhat independent paths. Functional images with single photon emission computed tomography (SPECT) and positron emission tomography (PET) are playing an increasingly important role in the diagnosis and staging of malignant disease, image-guided therapy planning, and treatment monitoring. SPECT and PET complement the more conventional anatomic imaging modalities of computed tomography (CT) and magnetic resonance (MR) imaging. When the functional imaging modality was combined with the anatomic imaging modality, the multimodality can help both identify and localize functional abnormalities. Combining PET with a high-resolution anatomical imaging modality such as CT can resolve the localization issue as long as the images from the two modalities are accurately coregistered. Software-based registration techniques have difficulty accounting for differences in patient positioning and involuntary movement of internal organs, often necessitating labor-intensive nonlinear mapping that may not converge to a satisfactory result. These challenges have recently been addressed by the introduction of the combined PET/CT scanner and SPECT/CT scanner, a hardware-oriented approach to image fusion. Combined PET/CT and SPECT/CT devices are playing an increasingly important role in the diagnosis and staging of human disease. The paper will review the development of multi modality instrumentations for clinical use from conception to present-day technology and the application software.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.30 no.2
• /
• pp.155-161
• /
• 2010

Recently, the electromagnetic techniques of the eddy current testing(ECT), alternating current field testing, magnetic flux leakage testing and remote field testing have been used as a nondestructive evaluation method based on the electromagnetic induction. The eddy current testing is now widely accepted as a NDE method for the heat exchanger tube in the electric power industry, chemical, shipbuilding, and military. The ECT system mainly consists of the synthesizer module, analog module, analog-to-digital converter, power supplier, and data acquisition and analysis program. In this study, the synthesizer module and the analog module which are essential to the ECT system were primarily developed. The developed ECT system is basically a multifrequency type which is able to inject the maximum four frequencies based on the frequency and time domain multiplexing method. Conclusively, we confirmed that the EC signal was processed appropriately in each circuit modules, and the Lissajous EC signal was displayed in the impedance plane.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.31 no.2
• /
• pp.127-133
• /
• 2011

A LabVIEW program has been developed together with simple infrared thermography(IRT) system to control the lock-in conditions of the system efficiently. The IR imaging software was designed to operate both of infrared camera and halogen lamp by synchronizing them with periodic sine signal based on thyristor(SCR) circuits. LabVIEW software was programmed to provide users with screen-menu functions by which it can change the period and energy of heat source, operate the camera to acquire image, and monitor the state of the system on the computer screen. In experiment, lock-in IR image for a specimen with artificial hole defects was obtained by the developed IRT system and compared with optical image.

• Journal of Digital Contents Society
• /
• v.18 no.1
• /
• pp.159-165
• /
• 2017

In order to solve problems in automatic quality inspection of tablet capsules, computation-efficient image processing technique, appropriate threshold setting, edge detection and segmentation methods are required. And since existing automatic system for quality inspection of tablet capsules is of very high cost, it needs to be reduced through the realization of low-price hardware system. This study suggests a technique that uses low-cost camera module to obtain image and inspects dents on tablet capsules and sorting them by applying TLS curve fitting technique and edge-based image segmentation. In order to assess the performance, the major classifications algorithm of PCA, ICA and SVM are used to evaluate training time, test time and accuracy for capsule image area and curve fitting edge data sets.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.3
• /
• pp.543-552
• /
• 1994

Dynamic Time Warp(DTW) needs for iterative calculations and the design of PE cell suitable for the operations is very important. Accordingly, this paper aims at real time recognition design enables large dictionary hardware realization using DTW algorithm. The DTW PE cell separated into three large blocks. "MIN" is the one block for counting accumulated minimum distance. "ADD" block calculates these minimum distances, and "ABS" seeks for the absolute values to the total sum of local distances. Circuit design and verification about the three block have been accomplished, and performed layout '||'&'||' DRC(design rule check) using 1.2 m CMOS N-Well rule base.CMOS N-Well rule base.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.40 no.4
• /
• pp.206-213
• /
• 2003

In this paper, we propose a design method of automatic thickness measurement and defect inspection system, which measures the thickness of the autoclaved lightweight concrete block and inspects the defect on a real-time basis. The image processing system was established with a CCD camera, an image grabber, and a personal computer without using assembled measurement equipment. For the realization of proposed algorithm, the preprocessing method that can be applied to overcome uneven lighting environment, threshold decision method, unit length decision method in uneven condition with rocking objects, and the curvature calibration method of camera using a constructed grid are developed. From the experimental results, we have found that the required measurement accuracy specification is sufficiently satisfied using our proposed method.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2009.04a
• /
• pp.212-215
• /
• 2009

옷감 시뮬레이션은 지금까지 게임, 애니메이션, 영화 등에 많이 사용되어왔고, 현재 증강현실(Augmented Reality) 환경에서의 교육자료, 쇼핑몰 뿐만 아니라 휴대용 게임기, 휴대폰 등 모바일 기기에서도 그 응용이 점점 증가하는 추세다. PC에 비해 그래픽스 하드웨어의 성능이 떨어지는 기기에서 3차원 시뮬레이션을 가능하게 하기 위해서는 모델의 움직임을 최대한 근사(Approximation)하면서 계산 속도를 보장하는 방법이 필요하다. 즉, 상호작용(Interaction)이 필요한 사용자 입장에서는 최소한의 정확성만 보장한다면 실시간 시뮬레이션이 더 큰 이슈가 된다. 따라서 이 논문에서는 증강현실 환경에서 실시간 시뮬레이션을 보장하는 옷감 시뮬레이션 방법을 제안한다. 안정성과 정확성이 보장되는 적분법(Integration)을 사용하였고, 옷감의 길이가 비사실적으로 늘어나지 않게 하기 위해 제약 조건(Constraints)을 주었다. 또한 각 지점에서의 곡률(Curvature)을 고려하여 충돌 검사를 함으로써 옷감 내부 충돌 검사로 요구되는 많은 계산량을 효율적으로 처리하였다.