• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.7
• /
• pp.4842-4848
• /
• 2015

This paper presents a comparison of communication performance between the reconfigurable beam-steering antenna and the omni-directional (loop) antenna during standstill and walking motion. Both omni-directional and reconfigurable antennas were manufactured on the same fabric (${\varepsilon}_r=1.35$, $tqn{\delta}=0.02$) substrate and operated around 5 GHz band. The reconfigurable antenna was designed to steer the beam directions. To implement the beam-steering capability, the antenna used two PIN diodes. The measured peak gains were 5.9-6.6 dBi and the overall half power beam width (HPBW) was $102^{\circ}$. In order to compare the communication efficiency, both the bit error rate (BER) and the signal-to-noise ratio (SNR) were measured using a GNU Radio Companion software tool and user software radio peripheral (USRP) devices. The measurement were performed when both antennas were standstill and walking motion in an antenna chamber as well as in a smart home environment. From these results, the performances of the reconfigurable beam steering antenna outperformed that of the loop antenna. In addition, in terms of communication efficiencies, in an antenna chamber was better than in a smart home environment. In terms of movement of antennas, standstill state has better results than walking motion state.

• Research in Plant Disease
• /
• v.19 no.2
• /
• pp.95-101
• /
• 2013

Black rot caused by Xanthomonas campestris pv. campestris (Xcc) is one of the most serious diseases of crucifers world-wide. To establish the efficient screening method for resistant cabbage to Xcc, different inoculation methods, inoculation positions, growth stages of seedlings, and incubation temperatures after inoculation were investigated with the seven cabbage cultivars showing different resistance degrees to the pathogen. Clipping with mouse-tooth forceps was better inoculation method than piercing with 18 pins or cutting with scissors to distinguish the level of resistance and susceptibility. In inoculation using mouth-tooth forceps, clipping the edges of the leaves near veins is more effective than injuring the veins of the leaves directly. In addition, the inoculated plants kept at $22^{\circ}C$ showed more clear resistant and susceptible responses than those kept at 26 or $30^{\circ}C$. On the basis of the results, we suggest that an efficient screening method for resistance of cabbage cultivars to black rot is to clip the edges of the leaves near veins of the four-week-old seedlings with mouth-tooth forceps dipped in a suspension of Xcc at a concentration of $7{\times}10^7$ cfu/ml and incubate the inoculated plants in a growth room at $22^{\circ}C$ with 12-hr light a day.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.15 no.1
• /
• pp.99-106
• /
• 1982

Vacuum-packed and seasoned-dried products of filefish, Navodon modestus, caught in large quantities in the coasts of Japan and Korea, were prepared tentatively and stored at $35^{\circ}C$ for $3\sim4$ months to test their keeping quality. Headed, eviscerated, ana skinned filefish were purchased from Tokyo central wholesale market and filleted. The fillets were seasoned with the seasoning powder prepared from sugar, sorbitol, salt, glutamate, 5'-ribonucleotide, and either beef flavor (Flava-Beef, Kyowa Hakko Kogyo Co. Ltd.), red pepper, or smoke flavor (Smok-EZ, Alpha Foods Co. Ltd.). After seasoning, the fillets were dried at $39\sim41^{\circ}C$ for several hours, vacuum-packed in the bag of plastic film, and cooked in water of $80^{\circ}C$ for 40 min. Two kinds of products different in moisture level were prepared : one containing moisture of $26\sim29\%$ and the other $40\sim46\%$. The moisture level, water activity, color value (L,a, and b values), texture, and viable counts of bacteria of these products were determined during storage at $35^{\circ}C$. From the results obtained, it became clear that the products could be preserved in good condition for $3\sim4$ months at $35^{\circ}C$, though they slightly decreased in the softness with decrease of moisture content and developed a pale brown during storage. Judging from organoleptic evaluation on the flavor, the products containing beef flavor as a seasoning was most desirable.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.697-698
• /
• 2013

최근에 유연한 성질을 갖는 전자기기들의 수요가 증가하면서, 그에 따라서 유연 전자기기를 뒷받침 해줄 수 있는 에너지 저장체의 유연한 성질도 중요성이 점점 부각되고 있으며 많은 연구가 진행되고 있다. 유연한 에너지 저장체의 많은 연구들이 유연한 금속 박막이나 특수 공정처리가 필요한 고분자를 이용하고 있으나, 대부분의 유연 에너지 소자들은 에너지 저장체의 성능에 비해 고온과 산 약품과 같은 환경이 필요하며, 비용과 시간이 많이 소모되고 있다. 그에 반해 섬유는 앞에서와 같이 특수 공정 처리가 따로 필요하지 않으며 상온에서도 손 쉽게 이용 가능하며, 신축성이 뛰어난 장점이 있기 때문에 효율적, 비용적으로 유연한 에너지 저장체에 유리한 소재이다. 몸에 해로운 산과 같은 약품처리의 필요도 없으며, 용매를 흡수하는 능력이 뛰어나기 때문에 용매를 이용한 도포 방법을 사용하면 다양한 물질을 폭넓게 적용 가능하다. 그리고 적용 분야에 맞춰서 섬유의 종류를 조절하면 다양한 성질을 갖는 천 기반의 에너지 저장체가 형성되며, 면 섬유가 수소 결합과 높은 반데르 발스 결합에 의해 탄소나노튜브와 결합하여 높은 에너지 밀도를 갖는 에너지 저장체를 형성하는 것을 분석한 논문들도 보고되고 있다. 면 섬유의 특수한 성질을 이용하여 에너지 저장체를 제작하고 이를 확인하기 위해서 일반 합성 섬유인 polyester와 면 섬유를 비교 제작하였으며, 용매의 형태로 손쉽게 도포 가능한 물질은 탄소 계열의 활물질들이며, 탄소 나노 튜브나 그래핀 등이 분산된 용액을 이용해 천에 도포 가능하다. 탄소 계열의 활물질들은 대표적인 슈퍼캐패시터 물질이며, 천에 도포를 함으로써 천 기반의 슈퍼캐패시터를 제작하였다. 일반 합성 섬유 polyester와 CNT를 결합한 형태의 전극은 최대 에너지 축전 용량(Maximum specific capacitance)이 53.6 F/g으로 나타났으며, 면 섬유와 CNT를 결합한 형태의 전극은 최대 에너지 축전 용량이 122.1 F/g으로 나타났다. 따라서 면 섬유에서 높은 에너지 저장 능력을 보이는 것을 실험적으로 확인하였으며, 에너지 저장 능력이 뛰어난 면 섬유를 다음 전극 디자인에서도 일률적으로 적용하였다. 슈도캐패시터의 대표적 물질인 금속 산화물인 망간 산화물(MnO2)을 3전극 도금 시스템을 이용하여 에너지 축전 용량과 에너지 밀도를 올리는 전극을 제작하였다. 특히 망간 산화물의 형태는 표면적을 극대화하기 위해서 평균 지름은 200~300 nm 정도 되는 나노 입자의 형태로 제작하였다. 그 결과, 확연하게 에너지 축전 용량이 향상되었으며, 최대 에너지 축전 용량은 282.0 F/g, 에너지전력 밀도는 14.2 Wh/kg으로 나타나서 금속 산화물의 형태가 주는 효과를 확인할 수 있었다. 하지만 나노 입자의 형태로 제작된 금속 산화물은 문제점이 발생하였다. 금속 산화물의 전기 전도성이 매우 낮기 때문에, 전기 전도성에 비례해서 전력 밀도의 값이 표현되는데, 전기 전도성이 급격히 감소하기 때문에 전력 밀도도 급격한 감소가 나타난다. 다음과 같이 전기 전도성 물질을 첨가하는 방법은 추가의 공정이 필요한 단점이 있지만 오직 기계적인 인장응력만을 가해서 에너지 밀도와 전력 밀도를 증가시키는 전극을 제작하였다. 인장응력을 섬유 기반의 전극에 가했을 시에 가닥들간의 접촉 증가와 CNT가 정렬되면서 특정 변형률(strain) 이전에서는 전기 전도성이 최대 50% 이상 증가하는 것을 확인할 수 있었으며, 선행 연구에서 보고되었다. 이를 이용해서 전기 전도성과 직결되는 전력 밀도의 양도 증가시키고 에너지 밀도의 증가 여부까지 확인한 결과 인장을 가하기 전 면 섬유의 전력 밀도와 에너지 밀도는 6.4 kW/kg and 6.1 Wh/kg으로 나타났으나 30% 변형 인장 후에는11.4 kW/kg과 7.1 Wh/kg으로 나타났다. 그리고 망간 산화물을 첨가한 전극 역시 4.9 kW/kg과 14.2 Wh/kg으로 나타났었으나 인장 이후 전력 밀도는 14.2 kW/kg, 에너지 밀도는 17.6 Wh/kg으로 확연하게 증가한 것을 확인하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.9
• /
• pp.5796-5800
• /
• 2014

This paper presents reconfigurable beam steering patch antenna with high gain for a wireless headset. Because existing antenna for wireless communication in headsets has an omni-directional radiation pattern, it has a deleterious effect in the vicinity of the human head. To reduce this effect, this paper proposed an antenna comprised of a U-slot and manufactured on a FR-4 substrate. The antenna operating at the 2.37-2.5 GHz band used a tapered matching method to match the impedance between the feed part and patch part. To implement the beam steering capability, the antenna used two PIN diodes. Using PIN diodes, the antenna presented three states ($S_0$, $S_1$ and $S_2$) in the maximum beam directions of the YZ-plane ($0^{\circ}$, $30^{\circ}$ and $330^{\circ}$, respectively). The peak gains of the antenna in the headset were 4.22-5.15 dBi. The fabricated antenna could communicate efficiently with a wireless headset.

• Journal of the Korea Concrete Institute
• /
• v.18 no.5 s.95
• /
• pp.603-610
• /
• 2006

The external unbonded strengthening offers advantages in speed and simplicity of installation over other strengthening techniques. Unlike externally bonded steel plate or carbon fiber sheet, surface preparation of the concrete for installation of high-tension bar is not required and installation is not affected by environmental conditions. Anchoring pin or anchoring plate are installed at the end of beam to connect the high-tension bar to concrete beam. The deviator are used in order that supplementary external bars would follow the curvature of the tested beam. A set often laboratory tests on reinforced concrete beam strengthened using the technique are reported. The main test parameters are the section area of strengthening bar, the depth of deviator and the number of deviators. The paper provides a general description of structural behavior of beams strengthened using the technique. The test result of strengthened beam are compared with those from a reference specimen. It is shown that the reinforcing technique can provide greater strength enhancements to unstrengthened beam and that the provision of deviator enhances efficiency. The ultimate moment of specimen with two deviators was higher than that of specimens with one deviator. It is also shown that the external bars enhance strength of beams in shear.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.2
• /
• pp.121-129
• /
• 2008

In this paper, we present a fast analysis of multilayer microstrip fractal structure by using the fast multipole method (FMM). In the analysis, accurate spatial green's functions from the real-axis integration method(RAIM) are employed to solve the mixed potential integral equation(MPIE) with FMM algorithm. MoM's iteration and memory requirement is $O(N^2)$ in case of calculation using the green function. the problem is the unknown number N can be extremely large for calculation of large scale objects and high accuracy. To improve these problem is fast algorithm FMM. FMM use the addition theorem of green function. So, it reduce the complexity of a matrix-vector multiplication and reduce the cost of calculation to the order of $O(N^{1.5})$, The efficiency is proved from comparing calculation results of the moment method and Fast algorithm.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.2
• /
• pp.282-287
• /
• 2018

Due to limitations in responding to oil spill incidents that are urgent or that cover a wide area with only oil spill response vessels, Korea Coast Guard (KCG) patrol vessels are utilized. In this study, we have developed an oil sweep system suitable for small patrol vessels. The equipment consists of three components - fixed support, poles, and slide fixers - and can be fastened with a toggle pin to a fall prevention bar on small patrol vessels without welding or additional efforts for installation. The respective weights of each component - fixed support, poles (2 pcs), and slide fixers (4 pcs) - are approximately 9.2 kg, 6.5 kg, and 3.5 kg. The 3 m-pole, which is rotatable 180 degrees horizontally, is folded deckward when replacing oil absorbents. As the development of this equipment has improved the method of deploying and retrieving oil absorbents on KCG small patrol vessels, we expect that more efficient oil spill cleanup will be possible.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.7
• /
• pp.1777-1783
• /
• 2014

In this paper, we designed and fabricated a high-speed semiconductor sensor for use in power control devices and analyzed the characteristics with pulsed radiation tests. At first, radiation sensitive circular Si PIN diodes with various diameters(0.1 mm ~5.0 mm) were designed and fabricated using Si epitaxial wafer, which has a $42{\mu}m$ thick intrinsic layer. The reverse leakage current of the diode with a radius of 2 mm at a reverse bias of 30 V was about 20.4 nA. To investigate the characteristic responses of the developed diodes, the pulsed gamma-radiation tests were performed with the intensity of 4.88E8 rad(Si)/sec. From the test results showing that the output currents and the rising speeds have a linear relationship with the area of the sensors, we decided that the optimal condition took place at a 2 mm diameter. Next, for the selected 2 mm diodes, dose rate tests with a range of 2.47E8 rad(Si)/sec to 6.21E8 rad(Si)/sec were performed. From the results, which showed linear characteristics with the radiation intensity, a large amount of photocurrent over 60mA, and a high speed response under 350ns without saturation, we can conclude that the our developed PIN diode can be a good candidate for the sensor of power control devices.

• Journal of Navigation and Port Research
• /
• v.29 no.5 s.101
• /
• pp.389-394
• /
• 2005

The additional moment occurs because the superstructures of VLFS are influenced by wave loads instead of earthquake loads. In order to reduce the additional moment, this study used the semi-rigid connections which lie between fully rigid and pinned. If the semi-rigid connections are used for superstructures of VLFS, the moment of beams can be reduced and more economical construction will be possible. This study aims to show the effect of wave loads on structure and the efficiency of the semi-rigid connections due to wave loads by analyzing the time history responses. The dynamic behaviors of the rigid frame are compared with those of the semi-rigid frame considering of static loads, wave loads and combination loads for a four-bay, three-story frames. The semi-rigid connection type is a steel tubular column with square external-diaphragm connections and the time history analysis is used for the dynamic responses. The additional moment responses due to wave loads increase $33\%$ in the rigid frame, $26\%$ in the semi-rigid frame with the spring model.