• 한국추진공학회지
• /
• 제5권3호
• /
• pp.19-24
• /
• 2001

대기중에서 움직이는 비행체(항공기, 미사일 등)의 속도 및 고도를 측정하기 위한 장치가 피토관 (Pilot-Tube)이다. 고속으로 비행하는 항공기의 안전하고 효율적인 운항을 위해서는 정확한 비행속도 및 고도측정이 요구된다. 피토관 최적 설계인자 결정을 위해 피토관 Nose의 Inlet부, Nose부 외곽형 상, 정압홀의 형상 및 정압홀 설치 위치 선정을 위한 유동장 해석을 수행하였다. 또한 해석을 통해 얻은 설계자료를 기본으로 제작한 피토관의 풍동실험을 수행하였다. 본 연구를 통해 속도 및 고도 계측용 피토관의 설계기술을 확보하였고 제작기술을 보유하였으며, 유동해석 및 풍동실험을 함으로써 피토관 국산화에 필요한 기본 자료를 얻었다.

• 대한기계학회논문집B
• /
• 제30권4호
• /
• pp.373-380
• /
• 2006

Annubar is one of popular tools to measure the exhausted gas flow rate from the stacks. For the accurate monitoring of the amount of discharged pollutants, calibration of annubar is very important. Calibration of annubar has been carried out in a wind tunnel. When the length of annubar is longer than the test section size of wind tunnel, it is very difficult to find out typical value of annubar coefficients. So, a measurement technique to calibrate annubar longer than the size of the test section of wind tunnel must be developed. In the present study, an experiment is performed to measure the annubar coefficients in such a limited size of the wind tunnel. The experimental annubar coefficient by using a partial blocking technique is very close to the annubar coefficient of normal condition.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 1997년도 강연회 및 연구개발 발표회 논문집
• /
• pp.206-214
• /
• 1997

• 한국항공우주학회지
• /
• 제33권4호
• /
• pp.47-56
• /
• 2005

무인기의 INS/GPS/기압고도계 결합항법 시스템에서 수직채널감쇠루프를 사용하여 고도 오차를 보정할 때 비행 고도의 오차를 감소시키기 위해서 기압고도계의 정밀도를 향상시켜야한다. 피토정압관을 사용하여 기압 고도를 측정할 때 비행 속도와 자세 등의 변화에 따라 피토정압관 주위의 압력이 변하여 정압 오차에 의한 기압 고도의 오차를 유발한다. 정압 오차를 보정하기 위하여 풍동 시험과 CFD, 비행 시험 등의 자료를 이용하여 피토정압관 측정 압력의 변화를 분석하고 받음각과 비행 속도에 따른 압력 오차의 모델을 수립하였다. 비행 속도 변화에 의한 오차를 보정하기 위하여 피토정압관의 차압과 차압/정압 비를 사용한 두 가지 오차 모델에 대하여 압력 섭동에 대한 민감도 해석을 하였고 비행 시험에 적용하여 차압/정압 비를 사용한 모델이 고고도 비행 특성이 우수하다는 결론을 얻었다.

• 대한기계학회논문집B
• /
• 제32권5호
• /
• pp.392-399
• /
• 2008

Accurate measurement of speed and altitude of flying vehicles in air data system remains a critical technical issue. A highly reliable Pitot-static probe is required to obtain air data such as total pressure and static pressure. In this study, an analysis of the characteristics of flowfield around the Pitot-static probe was performed by using a Navier-Stokes CFD code. In addition, for the purpose of finding an optimal configuration, a technique based on the response surface method is applied to the problem with design parameters including shape of the nose section and cone angle. It is shown that the optimal configuration fulfills the MIL specification in wider range of high angles of attack.

• 한국유체기계학회 논문집
• /
• 제4권2호
• /
• pp.35-43
• /
• 2001

The flow characteristics passing a multi-point Pitot tube flow-meter of diamond shape and the characteristics of flow coefficients of the flow-meter are experimentally studied by varying combination of upstream rectangular dual elbows. The results provide the flow coefficients, which show good stability and reliability within the Reynolds number range coveted here in this study, and which can be used to measure flow-rates in practice. The variation of dual elbows upstream can change the velocity field so much that the flow pattern might thwart the precise flow measurement using the multi-point Pitot tube. The strongest swirl is detected in the case of $90^{\circ}$ dual elbow combination of all. In addition, it is observed that flow separation remains unchanged and occurs at the same point irrespective of various upstream dual elbow combinations.

• 대한기계학회논문집B
• /
• 제27권12호
• /
• pp.1750-1757
• /
• 2003

This paper describes the flow measurements inside the blade passage of an axial flow fan by using a rotating hot-wire probe sensor from a relative flame of reference fixed to the rotor blades. The validity of fan rotor designed by a streamline curvature equation was performed by the measurement of the three-dimensional flow upstream and downstream of the fan rotor using a 5-hole pitot tube. The vortical flow structure near the rotor tip can be clearly observed by the measurements of a relative velocity and its fluctuation on quasi-orthogonal planes to a tip leakage vortex. Larger vortical flow, which results in higher blockage in the main flow, is formed according to decrease a flow rate. The vortical flow spreads out to the 30 percent span from the rotor tip at near stall condition. In the design operating condition, the tip leakage vortex is moved downstream while the center of the vortex keeps constant in the spanwise direction. Detailed characteristics of a velocity fluctuation with relation to the vortex were also analyzed.

• 대한조선학회논문집
• /
• 제34권2호
• /
• pp.11-19
• /
• 1997

선미 반류분포를 계측하기위해 수조에서 흔히 사용하는 5공 피토관의 새로운 캘리브레이션 방법을 제안하였다. 기존의 한 각도(수평 또는 수직)만을 고려하는 1차원 캘리브레이션 방법과는 달리, 본 논문에서 제안한 2차원 차트 캘리브레이션 방법은 수평각과 수직각을 동시에 변화시켜 얻어진 2차원 차트를 이용하여 종전에 큰 각도에서 발생하던 오차를 줄임으로써 계측 정도를 크게 향상시켰다. 또한 종래의 1차원 방법에 맞추어 구성된 계측 시스템을 수정 없이 사용할 수 있도록 상관계수를 정의함으로써 사용의 편의를 도모하였다.

• 한국유체기계학회 논문집
• /
• 제19권2호
• /
• pp.5-10
• /
• 2016

Gas flow measurement in a closed duct was performed using multi-point Pitot tubes. Measurement uncertainty was assessed for this measurement method. The method was applied for the measurement of air flow into a gas turbine engine in an altitude engine test facility. 46 Pitot tubes, 15 total temperature Kiel probes and 9 static pressure tabs were installed in the engine inlet duct of inner diameter of 264 mm. Five tests were done in an airflow range of 2~10 kg/s. The flow was compressible and the Reynolds numbers were between 450,000 and 2,220,000. The measurement uncertainty was the highest as 6.1% for the lowest flow rate, and lowest as 0.8% for the highest flow rate. This is because the difference between the total and static pressures, which is also related to the flow velocity, becomes almost zero for low flow rate cases. It was found that this measurement method can be used only when the flow velocity is relatively high, e.g., 50 m/s. Static pressure was the most influencing parameter on the flow rate measurement uncertainty. Temperature measurement uncertainty was not very important. Measurement of boundary layer was found to be important for this type of flow rate measurement method. But measurement of flow non-uniformity was not very important provided that the non-uniformity has random behavior in the duct.

• 한국자동차공학회논문집
• /
• 제4권4호
• /
• pp.72-79
• /
• 1996

The recent trend of higher output engines with more auxiliary parts is resulting in greater heat generation in the engine compartment. In order to maximize the heat dissipation and eliminate the inefficient flow in the engine compartment, it is necessary to understand the flow field under the hood. In this respect, experimental study as well as numerical analysis should be conducted. The automated measuring system was constructed to obtain three dimensional mean flow data with high accuracy. The measurements have been made on a vehicle with a steady incoming air flow. The result shows that there exists a high degree of non-uniformity in the mean flow velocity at the front of radiator.