• Journal of Welding and Joining
• /
• v.19 no.1
• /
• pp.112-117
• /
• 2001

The factor affecting on the fatigue strength of spot welded specimen have been studied. To analyze and predict crack initiation position and propagation directions on the spot welded area are very important for strength design of the automobile body structure. In fact, there are a various of loads in running automobile but, it is impossible to replay like an actual conditions in the laboratory. So, in this study tensile-shear type and in-plane bending type specimens were used in fatigue test and includes an analysis of fatigue crack initiation position and propagation directions about earth specimens. The results obtained in the present study are summarized as follows: 1. In tensile-shear type fatigue test, the region of fatigue crack initiation position was affected by out-of-plane bending deformation due to bending angle. 2 In in-plane bending type fatigue test, the behavior of fatigue crack initiation position and propagation derections due to angle between upper plate and lower plate was dominated by magnitude of in-plane bending moment.

• Korean Journal of Materials Research
• /
• v.25 no.4
• /
• pp.183-190
• /
• 2015

Fatigue crack growth rate tests were conducted as a function of temperature, dissolved hydrogen (DH) level, and frequency in a simulated PWR environment. Fatigue crack growth rates increased slightly with increasing temperature in air. However, the fatigue crack growth rate did not change with increasing temperature in PWR water conditions. The DH levels did not affect the measured crack growth rate under the given test conditions. At $316^{\circ}C$, oxides were observed on the fatigue crack surface, where the size of the oxide particles was about $0.2{\mu}m$ at 5 ppb. Fatigue crack growth rate increased slightly with decreasing frequency within the frequency range of 0.1 Hz and 10 Hz in PWR water conditions; however, crack growth rate increased considerably at 0.01 Hz. The decrease of the fatigue crack growth rate in PWR water condition is attributed to crack closure resulting from the formation of oxides near the crack tips at a rather fast loading frequency of 10 Hz.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.2
• /
• pp.110-116
• /
• 2002

At elevated temperature, very complex precipitations occur in STS316. To investigate the effect of the precipitation on mechanical properties in SIS316, tensile tests and fatigue crack growth tests were carried out at $650^{\circ}C$ using artificially degraded materials. The material degradation was simulated by aging for up to 20000 hrs. at $750^{\circ}C$, which is equal to 179000hrs (about 20yrs) of service life at $650^{\circ}C$, after conducting solution treatment for 20 min. at $11300^{\circ}C$. The result of the hardness test and the tensile test showed that both properties are closely related to the mean free distance of carbides. Also, from the results of fracture tests at $650^{\circ}C$, ${\triangle}K_{th}$, after values were found to decrease as aging time and microstructure, as the volume fraction of $\sigma$ phase increased.

• Journal of the Korean Society of Safety
• /
• v.20 no.1 s.69
• /
• pp.62-67
• /
• 2005

An eccentrically-loaded single edge crack tension specimen (ESET) is similar to a compact tension(CT) specimen loaded in tension-tension. The standard ESET specimen exhibits advantages over other types of cracked specimen, such as n, single-edge crack, and middle-crack tension specimen. The details of ESET specimen configuration, test procedure, and calculations are described in ASTM E647 standard. However, a difficulty in attaching COD gage to the knife-edge on the front foe of the specimen can be found when the size of ESET specimen is small for rapid cooling and heating in thermal fatigue testing. The finite element analysis is performed for the ESET specimen with projected knife-edge on the front foe and a crack-length-compliance equation is suggested for the new specimen configuration. Calibration test are conducted with 347 stainless steel to compare the measured crack length with the calculated crack length from the suggested compliance expression. The test results showed good agreements with those of analysis.

• Korean Journal of Materials Research
• /
• v.28 no.7
• /
• pp.398-404
• /
• 2018

Fatigue crack growth retardation of 304 L stainless steel is studied using a neutron diffraction method. Three orthogonal strain components(crack growth, crack opening, and through-thickness direction) are measured in the vicinity of the crack tip along the crack propagation direction. The residual strain profiles (1) at the mid-thickness and (2) at the 1.5 mm away from the mid-thickness of the compact tension(CT) specimen are compared. Residual lattice strains at the 1.5 mm location are slightly higher than at the mid-thickness. The CT specimen is deformed in situ under applied loads, thereby providing evolution of the internal stress fields around the crack tip. A tensile overload results in an increased magnitude of the compressive residual stress field. In the crack growth retardation, it is found that the stresses are dispersed in the crack-wake region, where the highest compressive residual stresses are measured. Our neutron diffraction mapping results reveal that the dominant mechanism is by interrupting the transfer of stress concentration at the crack tip.

• Journal of the Korean Society of Safety
• /
• v.16 no.3
• /
• pp.1-6
• /
• 2001

The study is to investigate the influence on the fatigue crack growth behaviors for the welded configuration in pressure vessel stiffener. In order to perform this goal, the automatic welded specimens were prepared. The material is ASTM A516 grade 60 steel used in pressure vessel mainly. In skip welding of pad-on-plate, continuous fillet welding and PWHT specimen, fatigue crack is generally initiated at the starting and end old toe zone, and ruptured at the starting old toe zone. The fatigue life of pad-on-plate of the continuous fillet welding specimen is larger than that of pad-on-plate skip fillet welding specimen about 85% under low load, about 20% under high load and less than that of two-pad continuous fillet welding specimen about 85%. In da/dN-$\Delta$K curve under low load, skip fillet welding specimen of pad-on-plate showed retardation on the initial crack, and the fatigue crack growth rate at the low region of $\Delta$K greater specimen E($3.8 {\times} 10^{-6}mm/cycle$). And the fatigue life of welding specimen was smaller than that of PWHT specimen.

• Journal of Welding and Joining
• /
• v.7 no.1
• /
• pp.28-35
• /
• 1989

The fatigue crack growth behavior in GTA butt welded joints of Al-Alloy 5052-H38 was examined using Single Edge Notched(SEN) specimens. It is well known that welding residual stress has marked influence on fatigue crack growth rate in welded structure. In the general area of fatigue crack growth in the presence of residual stress, it is noted that the correction of stress intensity factor (K) to account for residual stress is important for the determination of both stress intensity factor range(.DELTA.K) and stress ratio(R) during a loading cycle. The crack growth rate(da/dN) in welded joints were correlated with the effective stress intensity factor range(.DELTA.Keff) which was estimated by superposition of the respective stress intensity factors for the residual stress field and for the applied stress. However, redistribution of residual stress occurs during crack growth and its effect is not negligible. In this study, fatigue crack growth characteristics of the welded joints were examined by using superposition of redistributed residual stress and discussed in comparison with the results of the initial welding residual stress superposition.

• Journal of the Society of Naval Architects of Korea
• /
• v.28 no.1
• /
• pp.108-116
• /
• 1991

In the non-linear behavior of many materials, there is difference between the monotonic behavior by static load and the cyclic behavior by cyclic load. In particular, the short fatigue cracks to propagate in elasto-plastic stress concentrations(notches), are governed significantly by the cyclic behavior of materials. Accordingly, it is needed to investigate and compare the monotonic and cyclic behavior of materials. In the pressent study, the stress-strain relations of materials by monotonic and cyclic load tests were examined for 2 kinds of steels(SS41, HT80) and 5 kinds of Al-alloys(A5083-O, A6N01-T5, A7N01-T4, A7016-T6, A7178-T6). And the constants for mechanical properties of the materials were determined by experimental results, Moreover, when a notch was subjected to cyclic load, the effect of cyclic hardening property of materials on the variation of stress-strain amplitude in the notch tip was discussed by the application of Neuber's rule and experiments for a center notched plate.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.4
• /
• pp.368-375
• /
• 2013

Failure of small bore piping welds is a recurring problem at nuclear power plants. And the socket weld cracking in small bore piping has caused unplanned plant shutdowns for repair and high economic impact on the plants. Consequently, early crack detection, including the detection of manufacturing defects, is of the utmost importance. Until now, the surface inspection methods has been applied according to ASME Section XI requirements. But the ultrasonic inspection as a volumetric method is also applying to enforce the inspection requirement. However, the conventional manual ultrasonic inspection techniques are used to detect service induced fatigue cracks. And there was uncertainty on manual ultrasonic inspection because of limited access to the welds and difficulties with contact between the ultrasonic probe and the OD(outer diameter) surface of small bore piping. In this study, phased array ultrasonic inspection technique is applied to increase inspection speed and reliability. To achieve this object, the 3.5 MHz phased array ultrasonic transducer are designed and fabricated. The manually encoded scanner was also developed to enhance contact conditions and maintain constant signal quality. Additionally inspection system is configured and inspection procedure is developed.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.121-121
• /
• 2009

자동차는 코너 주행 시 In-corner와 Out-corner 의 바퀴 궤적이 달라지므로, 특별한 장치가 없이 좌우 구동 측의 바퀴가 같은 속도로 회전을 하게 되면 정상적인 주행이 불가능하다. 따라서 정상적인 코너 주행이 가능 하려면, 코너 안쪽 바퀴보다 바깥쪽 바퀴가 더 빨리 회전해야 하며 이러한 회전 차를 보상받지 못할 경우 바깥쪽 바퀴가 끌리는 현상이 발생하는데 이를 방지하기 위해 디퍼렌셜 기어가 필요하다. 현재 디퍼렌셜 기어는 디퍼렌셜 케이스와 링기어를 볼트로 체결하는 조립 공법을 통해 생산되고 있다. 하지만 볼트 체결 공법은 조립을 위한 볼트와 볼트 체결을 위한 플랜지와 볼팅을 위한 홀을 가공하는 공정이 필요하기 때문에 재료비 절감 및 생산 효율 향상에 매우 불리하고 볼트체결을 위한 부분 때문에 불필요한 무게가 증가하게 된다. 따라서 본 연구에서는 이러한 기계적 체결 방식을 레이저 용접 방식으로 대체하여 재료비를 절감하고 무게 저감을 통해 주행성능을 향상시키고자 하였다. 링기어의 소재는 침탄처리강(SCM420H)이며 디퍼렌셜 케이스의 소재는 주철(GCD500)을 사용하고 있다. 주철은 용접시 용접부와 열영향부에서 마르텐사이트 조직과 레데브라이트, 시멘타이트 조직이 생성되며 고탄소 모재의 탄소 확산으로 인한 부분 혼합영역에서 탄소 합금이 생성되어 균열이 발생하는 등 용접성이 매우 좋지 않은 것으로 알려져 있다. 이러한 주철의 난용접성을 해결하는 방법으로는 고탄소 모재 용접시 발생하는 탄소의 확산을 억제하거나 예열이나 후열 처리를 통한 냉각 속도의 제어하는 방법과 오스테나이트 안정화 원소를 첨가한 필러와이어를 사용하여 용접시 마르텐사이트와 시멘타이트의 성장을 방해하는 방법 등이 이용되고 있다. 본 연구에서는 예열처리나 후열처리를 통한 주철의 용접법은 대량 생산을 통한 원가절감을 노리는 자동차 업계의 특성에 비추어 볼 때 비용이나 프로세스 구성 면에서 적용하는 것이 어려울 것이라 판단하여 Ni-base filler metal을 통한 주철의 용접법을 선택하였고 그 결과 실차에 적용하기 위한 비틀림 강성 테스트나 내구 테스트는 통과하였으나 NVH 테스트 결과 볼팅 체결 방식에 비하여 소음이 커지는 문제가 발생하고 링기어의 HAZ부가 고경화 되는 문제가 발생하였다. 때문에 용입깊이를 초기 시제품인 5mm에서 4mm로 변경시켜 입열량 감소 및 용접변형을 줄여 소음 문제를 해결하고자 하였으며 링기어의 침탄층을 1mm 절삭하여 링기어 HAZ부의 고경화 문제를 해결하고자 하였다. 이러한 용접 구조 변경이 용접변형 및 강성과 피로에 미치는 영향력을 알아보고자 용접 및 열처리 상용 소프트웨어인 SYSWELD, 구조해석 상용소프트웨어인 NX_NASTRAN, 피로 해석 상용 소프트웨어인 FEMFAT을 이용하여 시뮬레이션 하였고 실제 구조 변경한 용접 시제품과 비교, 분석하였다.