• Applied Chemistry for Engineering
• /
• v.27 no.2
• /
• pp.165-170
• /
• 2016

In this study, we investigated the cause of the decrease in activities of $VO_x/TiO_2$ SCR catalyst used for the burner reactor at a scale of $150000Nm^3/hr$ using X-ray diffraction (XRD), brunauer-emmett-teller (BET), atomic emission spectroscopy inductively coupled plasma (AES ICP), $H_2$ temperature programmed reduction ($H_2$-TPR), and $NH_3$ temperature programmed desorption ($NH_3$-TPD) analysis. Since the crystallization of the $VO_x$ and phase transition of $TiO_2$ did not occur, it was concluded that the catalyst was not deactivated by the thermal effect. In addition, from the elemental analysis showing that a large quantity of calcium was detected but not sulfur, the deactivation process of the $VO_x/TiO_2$ SCR catalyst was mainly caused by Ca but not by $SO_2$. The calcium was also found to decrease the catalytic activity by means of reducing $NH_3$ adsorption.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.8
• /
• pp.855-861
• /
• 2013

Small-pore Cu-chabazite SCR catalysts with high NOx conversion at low temperatures are of interest for marine diesel engines with exhaust temperatures in the range of 150 to $300^{\circ}C$. Unfortunately, fuels for marine diesel engines can contain a high level of sulfur of up to 1.5% by volume, which corresponds to a $SO_2$ level of 500 ppm in the exhaust gases for an engine operating with an A/F ratio of 50:1. This high level of $SO_2$ in the exhaust may have detrimental effects on the NOx performance of the Cu-chabazite SCR catalysts. In the present study, a bench-flow reactor is used to investigate the effects of sulfur poisoning on the NOx performance of Cu-chabazite SCR catalysts. The SCR catalysts were exposed to simulated diesel exhaust gas stream consisted of 500 ppm $SO_2$, 5% $CO_2$, 14% $O_2$, 5% $H_2O$ with $N_2$ as the balance gas at 150, 200, 250 and $300^{\circ}C$ for 2 hours at a GHSV of 30,000 $h^{-1}$. After sulfur poisoning the low-temperature NOx performance of the SCR catalyst is evaluated over a temperature range of 150-$300^{\circ}C$ to determine the extent of the catalyst deactivation. Desulfation is also carried out at 600 and $700^{\circ}C$ for 30 minutes to determine whether it is possible to recover the NOx performance of the sulfur-poisoned SCR Catalysts.

• Korean Chemical Engineering Research
• /
• v.55 no.1
• /
• pp.107-114
• /
• 2017

The performance of polymer electrolyte membrane fuel cell (PEMFC) could be deteriorated when fuel contains contaminants such as carbon monoxide (CO) or hydrogen sulfide ($H_2S$). Generally, $H_2S$ is introduced in hydrogen by steam reforming of hydrocarbon which has mercaptan as odorant. $H_2S$ poisoning effect on PEMFC performance was examined on this study. Pure hydrogen injection, voltage cycling and water circulation methods were compared as performance recovery methods. The PEMFC performance was analyzed using electrochemical methods such as polarization curve, electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). Pure hydrogen injection and voltage cycling methods showed low recovery ratio, however, water circulation method showed high recovery ratio over 95%. Because anode was directly poisoned by $H_2S$, anode water circulation showed higher recovery ratio compared to the other methods. Water circulation method was developed to recover PEMFC performance from $H_2S$ poisoning. This method could contribute to PEMFC durability and commercialization.

• Proceedings of the Korean Environmental Sciences Society Conference
• /
• 2006.11a
• /
• pp.85-87
• /
• 2006

• Journal of Power System Engineering
• /
• v.14 no.6
• /
• pp.13-19
• /
• 2010

이 논문에서는 디젤자동차용 LNT와 SCR 촉매의 NO, $NH_3$ 흡착 및 탈리의 기본 특성과 수열화 온도와 시간 및 정량화된 황피독 농도에 대한 de-$NO_x$ 촉매의 내구성을 평가하였다. LNT 촉매는 열적으로 열화됨에 따라 Pt 및 Ba의 소결 및 응집으로 활성이 떨어져 $NO_x$ 전환율은 감소하였다. 반면에 Pt의 비활성화로 중간생성물인 $NH_3$ 생성량은 증가하였으며, 이때 생성된 $NH_3$는 LNT+SCR 복합시스템의 SCR 촉매의 환원제 역할을 담당한다. 1.0 g/L 이상의 황이 피독된 LNT 촉매는 탈황을 하여도 질소 산화물 흡장물질(Ba) 의 성능이 회복이 되지 않아 $NO_x$ 전환율은 회복되지 않았으며, 탈황 후 Pt 재활성화로 인해 NO2 및 SCR 환원제인 $NH_3$ 생성량은 증가하였다. SCR 촉매의 $NO_x$ 전환율은 $700^{\circ}C$ 36h, $800^{\circ}C$ 24h로 수열화 시킨 촉매는 전이금속 입자 성장 및 zeolite 구조 파괴로 인하여 급격하게 떨어졌으며, 0.36 g/L 황 피독된 촉매는 zeolite가 가지는 강산성 특정으로 내피독성이 강하여 탈황시 $NO_x$ 전환율은 회복되었다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.155-155
• /
• 2011

용융탄산염 연료전지(MCFC)는 $650^{\circ}C$에서 작동하는 고온형 연료전지 시스템이다. 이 시스템은 천연가스 등을 개질하여 생산된 수소를 바로 전기로 생산할 수 있는 시스템으로 열효율이 높으며, 현재 대체 발전시스템으로 각광을 받고 있다. MCFC는 개질방식에 따라 내부개질 방식과 외부개질 방식이 있다. 내부개질 방식은 수소를 생산하는 개질기가 스택내부에 장착된 형식으로 천연가스를 스택내부에서 개질하여 바로 전기를 생산하는 방식이다. 이 내부개질반응에 사용되는 촉매로는 알루미나에 고함량 (약 50 wt.%)으로 담지된 니켈(Ni) 계열촉매이 주로 쓰이고 있다. 이 고함량으로 담지된 촉매는 대부분 높은 활성을 보인다. 비교적 낮은 온도 운전조건 (약 $580{\sim}620^{\circ}C$)을 가지는 MCFC 내부개질에 적용하기 위해서는 활성점인 니켈을 최대한 담지체에 고르게 분산 시켜야한다. 이를 위해서 MgO를 이용하여 촉매의 활성점을 높게 분산시키는 연구를 진행 하였다. 촉매를 제조하는 방법으로 요소(urea)를 이용한 균일용액침전법을 이용하였다. 니켈함량은 50 wt.%로 고정을 한 다음, MgO 양과 $Al_2O_3$ 양을 각각 0 ~ 45 wt.%와 5 ~ 50 wt.%로 조절하면서 촉매를 제조하여 그 특성들을 분석하였다. 물성을 비교하기 위해서, X-선 회절분석 (XRD) 및 TPR, 물리화학흡착 실험을 하였다. 촉매의 활성을 살펴보기 위해서, fresh 상태 및 피독 상태에서 메탄수증기 개질활성 실험을 실시하였다. MgO 함량이 없거나 적은 촉매에서는 높은 BET surface area와 작은 NiO, metallic Ni 결정 크기가 나타났다. 반면 MgO 함량이 높은 촉매에서 낮은 BET surface area와 비교적 큰 NiO, metallic Ni 결정 크기가 나타났다. 또한 XRD 분석에서 MgO 함량이 증가할 수 록 MgO 결정 피크가 명확히 나타났으며, $MgAl_2O_4$ 피크는 나타나지 않았다. TPR 분석에서 촉매들의 환원 피크를 측정한 결과, 저함량의 MgO를 포함한 촉매는 $700^{\circ}C$ 부근에 환원 피크가 관찰되었고 MgO가 고함량인 촉매는 환원 피크가 $400^{\circ}C$ 부근에서 관찰되었다. 촉매의 초기 fresh 상태에서의 활성은 고함량 MgO를 포함한 Ni-90M10A 샘플을 제외하고 모든 촉매가 거의 비슷하게 나타났다. 그러나 $K_2CO_3$ 피독 상태에서는 MgO 함량이 증가할 수 록 활성이 좋지 않았음을 알 수 있었다. 따라서 MgO가 소량 포함된 촉매의 경우 fresh 상태에서는 우수한 물성과 활성을 보이지만, 피독상태에서는 MgO가 포함되지 않은 Ni-$Al_2O_3$ 촉매가 우수한 활성을 보였다.

• Applied Chemistry for Engineering
• /
• v.30 no.6
• /
• pp.731-736
• /
• 2019

In this article, Pt/TiO₂ was manufactured in the form of powder and honeycomb, and the influence of SO₂, which is a poisonous substance to catalyst, and regeneration method were investigated. The catalytic activity of Pt/TiO₂ before and after the exposure to SO₂ was also compared. The initial activity of Pt/TiO₂ was proportional to the injected H₂ concentration (1~5%). And the optimum temperature of the catalyst and conversion rate of H₂ were 183 ℃ and 95%, respectively. It was confirmed that when exposing 2,800 ppm of SO₂ to the powder and honeycomb Pt/TiO₂, the performance of catalyst was not measurable and also 0.69% sulfur (S) remained on the catalyst surface. As a result of the cleaning and heat treatment for the poisoning catalyst, the activity of the powder catalyst exhibited a conversion rate of H₂ greater than 96%. Whereas, the honeycomb catalyst showed a conversion rate of H₂ greater than 95% when it was regenerated through the heat treatment of H₂ or air atmosphere.

• Applied Chemistry for Engineering
• /
• v.19 no.5
• /
• pp.574-581
• /
• 2008

The optimum regeneration conditions for the regeneration of three way spent catalysts (TWCs), which were taken from automobiles with different driving conditions, were investigated to evaluate the suitability as alternative catalysts for removing VOCs. The spent catalysts were washed with five different acids ($HNO_3$, $H_2SO_4$, $C_2H_2O_4$, $C_6H_8O_7$, and $H_3PO_4$) to remove contaminants and examine the optimum conditions for recovering the catalytic activity. The physicochemical properties of spent and its regenerated TWCs were evaluated by using nitrogen adsorption-desorption isotherms, XRD, and ICP. The relative atomic ratios of contaminants and platinum group metals (PGMs) of the spent TWCs were greatly dependent on the placed positions. The main contaminants formed were lubricant oil additives and metallic components. Also, the regeneration treatment increased the PGMs ratio, BET surface area, and average pore diameter of TWCs. The catalytic activity results indicated that the spent TWCs have the possibility for removing VOCs. Moreover, the employed acid treatments greatly enhanced the catalytic activity of the spent TWCs. Especially, nitric and oxalic acids provided the most improvement in the catalytic behavior. The catalytic activities of the regenerated TWCs were significantly influenced by the containing platinum ratios rather than the removal ratios of contaminants and the changes in the structural properties offered by the acid treatments.

• Clean Technology
• /
• v.14 no.1
• /
• pp.61-68
• /
• 2008

There have been great attentions on polymer electrolyte membrane fuel cell (PEMFC) due to their advantageous characteristics such as zero emission of hazardous pollutant and high energy density. In this work, we evaluated degradation phenomena and stability of single cell performance via one dimensional single cell modeling. Here, CO poisoning on anode on anode was considered for cell performance degradation. Modeling results showed that the performance and stability were highly degraded with CO concentration in fuel gas. In addition, cell performance was reduced by slow oxygen reduction on cathode in long term operation. In order to overcome, it is required to increase ratio o#hydrogen in the fuel gas of anode and high Pt loading contained in the cathodic catalyst layer.

• Journal of the Korean Electrochemical Society
• /
• v.25 no.2
• /
• pp.88-94
• /
• 2022

The anion exchange membrane used in alkaline membrane fuel cells transports hydroxide ions, and ion conductivity affects fuel cell performance. Thus, the measurement of absolute hydroxide ion conductivity is essential. However, it is challenging to accurately measure hydroxide ion conductivity since hydroxide ions are easily poisoned in the form of bicarbonate by carbon dioxide in the atmosphere. In this study, we applied electrochemical ion exchange treatment to measure the absolute hydroxide ion conductivity of the anion exchange membrane. In addition, we investigated the effect of carbon dioxide poisoning of hydroxide ions on electrochemical performance by measuring bicarbonate conductivity. Commercial anion exchange membranes (FAA-3-50 and Orion TM1) and polyphenylene-based block copolymer (QPP-6F) were used.