• Proceedings of the Korea Water Resources Association Conference
• /
• 2022.05a
• /
• pp.100-100
• /
• 2022

일반적으로 유체와 구조물간 상호작용의 수리동역학적 모의에서는 벽경계조건을 통하여 유동에 대한 구조물의 영향이 반영된다. 하지만 도심지에서 발생한 홍수를 예측하려는 경우 이러한 방법으로는 밀집한 구조물들 사이에 형성된 좁은 길들로 인하여 세밀한 격자망을 요하여 큰 계산량을 유발하고 빠른 예측 속도를 기대할 수 없게 한다. 최근 이러한 문제를 극복하기 위해 성긴 격자망에서도 구조물의 유체에 대한 영향을 반영할 수 있도록 하는 방법들이 큰 관심을 받고 있다. 그 중에서도 다공성 천수방정식은 벽경계조건 대신 다공도(posority)의 개념을 이용한 모형으로 도시범람모의에 있어 계산량과 정확도를 가장 적절하게 타협한 모형으로 보고되고 있다. 이러한 흐름에 맞추어 본 연구는 다공도 천수방정식을 해석하는 수치 기법을 개발하였고, 여기에 최근 쌍곡선계 방정식의 수치적 연구들에서 소개된 주요 특징들이 반영되도록 설계하였다. 우선, WENO 기법과 Runge-Kutaa 기법을 통하여 공간과 시간에 대한 고차 정확도를 만족시켰다. 이 때, 재구성 변수와 알고리즘를 새롭게 제시하여 정상흐름조건에 대한 플럭스항과 생성·소멸항간 절단오차에 의한 비물리적인 흐름생성을 억제하였다. 또한, 수치모의 중 음수심의 발생으로 인하여 수치모형이 불안정해지는 현상을 막기 위해, 양-보존성 제한자를 구축하였다. 마지막으로 도심지에서 즐비한 인위적인 구조물에 의해 나타나는 지형적인 불연속의 효과를 적절하게 반영할수 있도록 정상파 재구축의 단계를 구축하여 수치 기법에 반영하였다. 이렇게 구성된 수치기법은 리만문제의 해석해에 기반하여 기존의 주요 연구들의 결과와 비교되었고, 그 결과 본 연구의 방법이 정확성, 수렴성, 안전성의 측면에서 가장 우수함을 수치적으로 증명하였다.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.19 no.4
• /
• pp.232-245
• /
• 2017

In this study, the high-resolution numerical simulation results considering landuse characteristics are analyzed by using single layer Urban Canopy Model (UCM) in Weather Research Forecast (WRF). For this, the impact of urban parameters such as roughness length and anthropogenic heat in UCM is analyzed. These values are adjusted to Seoul metropolitan area in Korea. The results of assessment are verified against observation from surface and flux tower. Forecast system equipped with UCM shows an overall improvement in the simulations of meteorological parameters, especially temperature at 2 m, surface sensible and latent heat flux. Major contribution of UCM is appreciably found in urban area rather than non-urban. The non-urban area is indirectly affected. In simulated latent heat flux, applying UCM is possible to simulate the change similarly with observations on urban area. Anthropogenic heat employed in UCM shows the most realistic results in terms of temperature and surface heat flux, indicating thermodynamic treatment of UCM could enhance the skills of high resolution forecast model in urban and non-urban area.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.17 no.4
• /
• pp.384-398
• /
• 2015

In this paper, the high-resolution Weather Research and Forecasting/Noah-MultiParameterization (WRF/Noah-MP) modeling system is configured for the Cheongmicheon Farmland site in Korea (CFK), and its performance in land and atmospheric simulation is evaluated using the observed data at CFK during the 2014 special observation period (21 August-10 September). In order to explore the usefulness of turning on Noah-MP dynamic vegetation in midterm simulations of surface and atmospheric variables, two numerical experiments are conducted without dynamic vegetation and with dynamic vegetation (referred to as CTL and DVG experiments, respectively). The main results are as following. 1) CTL showed a tendency of overestimating daytime net shortwave radiation, thereby surface heat fluxes and Bowen ratio. The CTL experiment showed reasonable magnitudes and timing of air temperature at 2 m and 10 m; especially the small error in simulating minimum air temperature showed high potential for predicting frost and leaf wetness duration. The CTL experiment overestimated 10-m wind and precipitation, but the beginning and ending time of precipitation were well captured. 2) When the dynamic vegetation was turned on, the WRF/Noah-MP system showed more realistic values of leaf area index (LAI), net shortwave radiation, surface heat fluxes, Bowen ratio, air temperature, wind and precipitation. The DVG experiment, where LAI is a prognostic variable, produced larger LAI than CTL, and the larger LAI showed better agreement with the observed. The simulated Bowen ratio got closer to the observed ratio, indicating reasonable surface energy partition. The DVG experiment showed patterns similar to CTL, with differences for maximum air temperature. Both experiments showed faster rising of 10-m air temperature during the morning growth hours, presumably due to the rapid growth of daytime mixed layers in the Yonsei University (YSU) boundary layer scheme. The DVG experiment decreased errors in simulating 10-m wind and precipitation. 3) As horizontal resolution increases, the models did not show practical improvement in simulation performance for surface fluxes, air temperature, wind and precipitation, and required three-dimensional observation for more agricultural land spots as well as consistency in model topography and land cover data.

• Journal of Astronomy and Space Sciences
• /
• v.24 no.2
• /
• pp.155-166
• /
• 2007

We have designed a high resolution proton and electron telescope for the detection of high energy particles, which constitute a major part of the space environment. The flux of the particles, in the satellite orbits, can vary abruptly according to the position and solar activities. In this study, a conceptual design of the detector, for adapting these variations with a high energy resolution, was made and the performance was estimated. In addition, a parallel processing algorithm was devised and embodied using FPGA for the high speed data processing, capable of detecting high flux without losing energy resolution, on board a satellite.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.3
• /
• pp.259-267
• /
• 2017

Flow fields around a KARI-11-180 airfoil, SDM and transonic body are numerically simulated by using an unstructured meshes based compressible flow solver developed at KAIST. RANS equations are solved to analyse the flow fields and Roe's FDS method is adopted to evaluate convective fluxes. Turbulence effect of the flow fields is modeled by a SA model, SST model and ${\gamma}-{\widetilde{Re}}_{{\theta}t}$ model. It is found that smaller drag coefficients are predicted for the KARI-11-180 airfoil when a transition phenomenon is considered and small deviations exist between CFD and EFD results. For the SDM, flow separation is observed at a leading edge and calculated aerodynamic properties show similar tendencies to experimental results. A shock wave on main wings of the transonic body is successfully captured by the present flow solver at a Mach number 0.9. Estimated pressure profiles by means of the present CFD method also agree well with those of wind tunnel results.

• Applied Chemistry for Engineering
• /
• v.10 no.4
• /
• pp.563-567
• /
• 1999

Reverse osmosis concentration for cephalosproin C was studied using a polyamide composite membrane, FT-30 in spiral wound type with high solute rejection. The experiments were carried out in the aqueous solution of cephalosporin C for water flux, solute rejection and mass transfer coefficient under applied pressure of $4{\sim}20kg/cm^2$, feed concentration of 100~1000 mg/L and feed velocity of 2.8 and 5.6 L/min at room temperature. The effect of operating pressure on the separation of cephalosporin C showed that permeate flux increased with increasing operation pressure. These results are consistent with those predicted by Kedem-Katchalsky model. Solute rejection was nearly 1. The increase of feed concentration caused the reduction of cephalosporin C rejection, which was higher at low concentration than at high concentration, but degree of reduction was small.

• Membrane Journal
• /
• v.30 no.1
• /
• pp.66-77
• /
• 2020

The current study focused on the effect of twisting hollow fibers (HFs) in a module during forward osmosis operation mode. Computational fluid dynamics simulation was employed for a straight HF module and twisted modules with five different angles to predict the mass transfer and observe the draw solution profile in terms of concentration and pressure. The simulation results showed that when the membranes were twisted, the concentration was distributed more evenly and the pressure at the module outlet increased gradually as the twisting angle increased. As pressure at the outlet increased, the fluid velocity inside the membrane decreased and the residence time of fluid increased, thereby facilitating mass exchange across the membrane. This is evidenced by a doubling of the ratio of water flux through the membrane in module flux when the HFs were twisted.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2015.05a
• /
• pp.76-76
• /
• 2015

토양수분은 생태수문학에서 식생과의 상호작용의 중요한 인자이자, 대기와의 상호작용으로 인한 총체적인 물 순환에 밀접한 관련이 있다. 수문학적으로는 증발, 침투, 지하수 함량, 토양 침식, 식생 분포 등을 지배하는 중요한 요소이고, 특히 시 공간적 분포특성은 강수 사상 후 토양으로의 침투 및 토양수분의 재분포, 증발산과 불포화대에서의 오염물의 이송을 예측하는데 매우 중요하다. 또한, '07년 하천법 개정으로 증발산량 및 토양수분량이 신규 수문조사 항목으로 추가되어, 토양수분 측정에 대한 필요성이 높아졌다. 따라서, 2008년 5월, K-water연구원에서는 현재 시험유역으로 운영하고 있는 용담시험유역에 토양수분관측망(6개 관측소)을 구축하였다. 토양수분계는 토양수분을 결정하는 가장 중요한 인자인 강우자료의 획득이 이루어지는 지점에 설치하여 정확도와 신뢰도를 높일 수 있도록 용담시험 유역 내 6개 우량관측소에 설치하였다. 하지만 장비의 노후화에 따른 자료 취득의 어려움으로 인하여 2013년 4월, 토양수분계를 전면 교체하였다. 토양수분계는 기존의 FDR 방식에서 EC 농도에 대한 영향이 가장 적고, 플럭스 타워에 위치한 토양수분계 센서와 동일한 TDR 방식의 센서로 장비를 전면 교체하였다. 센서 설치 장소 변경에 따른 TDR 센서의 검증과 그리고 흙의 종류, 입도, 다짐도, 온도 등에 의한 오차가 발생 여부를 판단하기 위하여 이에 대한 보정을 실시하였다. 원지반 시료채취를 통하여 토양수분량을 측정하였고, TDR 센서에 의해 측정된 토양수분량과 채취된 시료에서 측정된 토양수분량의 결과를 비교하였고, 각 지점별 토양구성비와 전기전도도 조건을 고려하여 각 토층별 계수적용을 달리하여 센서 보정을 실시하였다. 그 결과 기존 센서 제조사에서 제안한 방정식을 그대로 사용하는 것 보다는 센서 검증을 통하여 얻은 계수보정에 의한 토양수분 변환식을 사용하는 것이 정확한 현장 자료를 확보할 수 있고, 신뢰도 높은 자료를 얻을 수 있다고 판단된다.

• The Korean Journal of Food And Nutrition
• /
• v.14 no.1
• /
• pp.34-39
• /
• 2001

The purpose of this study was to examine physical properties of the addition of green tea powder on bread flour and dough rheology of white pan bread. Three levels(0.1, 0.5 and 1.0% ) of each green tea powder with bread flour were tested for their effects in dough mixing using rapid disco analyzer, alveogram and farinogram. Addition of green tea powder tended to reduce initial pasting temperature and increase peak viscosity, break down and set back. L(extensibility) and G(swelling index) value in alveogram showed decrement with increasing green tea powder. These meant that the volume of white pan bread would show same tendency. The use of green tea powder increased consistency and water absorption of the bread flour but decreased development time, salability and degree of softening on farinogram. White pan bread with green tea powder had higher value of hardness and springness than without it. Sensory evaluation determined that the white pan bread with 0.5% green tea powder had the highest score.

• Journal of the Korean earth science society
• /
• v.42 no.5
• /
• pp.504-513
• /
• 2021

Different physical processes, according to the atmospheric boundary layer types, were used in the Local Data Assimilation and Prediction System (LDAPS) of the Unified Model (UM) used by the Korea Meteorological Administration (KMA). Therefore, it is important to verify the atmospheric boundary layer types in the numerical model to improve the accuracy of the models performance. In this study, the atmospheric boundary layer types were verified using observational data. To classify the atmospheric boundary layer types, summer intensive observation data from radiosonde, flux observation instruments, Doppler wind Light Detection and Ranging(LIDAR) and ceilometer were used. A total number of 201 observation data points were analyzed over the course 61 days from June 18 to August 17, 2019. The most frequent types of differences between LDAPS and observed data were type 1 in LDAPS and type 2 in observed(each 53 times). And type 3 difference was observed in LDAPS and type 5 and 6 were observed 24 and 15 times, respectively. It was because of the simulation performance of the Cloud Physics such as that associated with the simulation of decoupled stratocumulus and cumulus cloud. Therefore, to improve the numerical model, cloud physics aspects should be considered in the atmospheric boundary layer type classification.