• 한국기계가공학회지
• /
• 제9권3호
• /
• pp.76-82
• /
• 2010

A laborer always watched a process of production carefully but defective manufactures were inspected after press process. These inspections made a waste of human power and defective manufactures could make a serious damage of press mold. Therefore, AE(Acoustic Emission) system was introduced to prevention of the damage of the press molds, to a real time detection of defective manufactures and to save human power. AE system was introduced to solve this problem which is a detecting defective manufacture on real time and to prevent the damage of the press mold. In this research we get acoustic emission signal in accordance with weight and processing method of press by using AE sensor, Preamplifier, AE board signal board which occurs press processing and it analyzed various signal through using CMD8 software on the time. From the result, we found that the intensity and shape of the signal were changed according to the weight and processing type of the press. By using this special algorithm, it can judge the acoustic signal which occurs from press on real time.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2006년도 춘계학술대회 논문집
• /
• pp.127-131
• /
• 2006

There are being a lot of studies for achievement of high speed Dehydration, high-strength and Lightweight of washing machine in the latest washing machine business. It is essential that Press-joining Strength of Spin Drum Seaming division is improved .to attain that target. Generally, we are using Mechanical press-joining by Seaming and T.I.G (Tungsten Inert Gas) welding among part joint method. Mechanical press-joining method that is mainly using for Stainless Steel (STS430) Drum have lots of merit that consumption of energy is low more than welding and production costs cut down and generation of the corrosion is solved by removing weld zone defect and materials having different properties are enable to join without special equipment. But, it is difficult to realize joint strength required at high speed operation because joint strength of mechanical press-joining method is low remarkably in comparison with welding. Also, there are a lot of analysis difficulties and very limited research is under way due to the dynamic factor such as multistage plastic working, elastic recovery, residual stress etc. The results of this study show optimal joining condition for mechanical press-joining by performing lots of tensile joining strength test with various specimen under multi-change of important design factor such as seaming width, bead area and bead depth etc.

• 한국기계가공학회지
• /
• 제11권1호
• /
• pp.101-106
• /
• 2012

The press bulging process is very useful and productive method to produce round-type mechanical components which have not been able to be manufactured because of limitation of the conventional press technology. The application of the press bulging process has expanded very quickly in the hydraulic and electronic industry and more recently it has been used to produce other mechanical parts such as the automobile and shipping parts. This expanding application also has brought some unsolved problems and leads many researchers to put their effort into the die design of the press bulging process. In this study, to obtain the optimum die shape for the press bulging process, various process parameters have been considered such as corner radius, bulging height, pressing length, and forming load, etc. The main interest of this paper is to verify the press bulging process which has more than 4.0 in height-length ratio. From this aspect, Finite Element analysis shows great ability to simulate the precise deformation process and gives us manufacturing database. Consideration of strain, stress, and strain-rate for the various cases has been also taken to keep the forming load within a particular range.

• 한국기계가공학회지
• /
• 제9권4호
• /
• pp.14-25
• /
• 2010

Small cracks or chips of a product appear very frequently in the course of continuous production of an automatic press process system. These phenomena became the cause of not only defective product but also damage of a press mold. In order to solve this problem AE(Acoustic emission) system was introduced. AE system was expected to be very effective to real time detection of the defective product and for the prevention of the damage in the press molds In this study, for the pick and analysis of AE signals generated from the press process, AE sensors/pre-amplifier/analysis and processing board were used as frequently found in the other similar cases. For the analysis and processing the AE signals picked in real time from the normal or the detective products, specialized software called AE-win(software for processing AE signal from Physical Acoustics Corporation) was used. As a result of this work it was conformed that intensity and shape of the various AE signals differ depending on the weight of the press and thickness of sheet and process type.

• 한국기계가공학회지
• /
• 제7권2호
• /
• pp.66-71
• /
• 2008

The data of the deformation and the stress according to time are studied at upper model of press and lower model of the blanking plate applied by press with the width, length and height of 0.4 m and 0.6 m respectively. The press is pushing downward on the plate fixed at the lower floor. These data are compared and investigated through this study. By using these results, there is the maximum deformation at 4 corners in the lower plate model of aluminium alloy fixed at lower floor. This deformation incase of elapsed time of 0.6 second becomes 4 times as much as in case of elapsed time of 0.2 second. The quantity of deformation at the lower plate model becomes more than at the upper press model to the extent of 10%. At the lower plate model of aluminium alloy, there is the maximum Von-Mises equivalent stress at 4 corners and both sides of middle area on the lower plate model of aluminium alloy. This stress in case of elapsed time of 0.6 second becomes 6 times as much as in case of elapsed time of 0.2 second. The Von-Mises equivalent stress of lower plate model becomes 2 times as much as that of upper press mode.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.432-435
• /
• 2005

Extensive width reduction of slabs is an important technology to achieve continuous production between the steelmaking and hot rolling processes. Conventionally, a vertical roll process has been used to achieve extensive width reduction. However, it is impossible to avoid the defects such as dog-bone, fish tail and camber. The deformation behavior in the width sizing process is more favorable than that in conventional vertical rolling edger, i.e. the material better flows toward the center of slab. This study is carried out to investigate the deformation of slab by two-step sizing press. The FE-simulation is utilized to predict plastic deformation mode in compression by a sizing press of slabs far hot rolling. In this paper, the various causes of the asymmetrical rolling phenomena are mentioned for the purpose of understanding of rolling conditions. Analytical results of slab-deformation by sizing press are presented below in this study.

• 한국기계가공학회지
• /
• 제20권4호
• /
• pp.106-112
• /
• 2021

Thermoplastic microfluidic devices are used in BioMEMS for medical and biotechnology applications, such as gene extraction, DNA analysis, and virus detection. In this research, a simple fabrication protocol with a commercially available pneumatic hot press is proposed and demonstrated for polycarbonate microfluidic devices. Microfluidic channels with a width of 200 ㎛ and a height of 10 ㎛ were designed and machined onto a brass plate as a mold insert using a CNC milling machine. The resulting microfluidic channels on the mold insert were assessed and found to have an actual width of 198 ㎛ and a height of 10 ± 0.25 ㎛. The microfluidic channels were replicated on a polycarbonate sheet using the proposed replication technique at 146℃ for 20 minutes under a constant load of 2400 kgf. The devices were then naturally cooled to 100℃ while maintaining the same pressure. It was found that the microchannels were successfully replicated in the polycarbonate, with a width of 198 ㎛ and a height of 10.07 ㎛. The proposed replication technique thus offers the rapid mass production of high-quality microfluidic devices at a low cost with a process that, unlike conventional photolithography systems, does not require expensive equipment.

• 한국기계가공학회지
• /
• 제21권8호
• /
• pp.43-52
• /
• 2022

The vibration characteristics of a hammer press are important parameters for machine design and production control. In this study, a counterblow hammer press was mathematically modelled as a mass-spring-damper system in order to analyze its vibration characteristics. The forging efficiency was theoretically derived as a function of the mass ratio, momentum ratio, and the coefficient of restitution And the effects of the mass ratio, momentum ratio and the restitution coefficient on the forging efficiency were also investigated for two particular cases of the unit mass ratio and unit momentum ratio. Additionally, the vibration responses of the counterblow hammer press due to the ram colliding impact were analyzed, and the force transmitted to the foundation through the mounting unit was determined.

• 대한공업교육학회지
• /
• 제41권1호
• /
• pp.1-21
• /
• 2016

이 연구의 목적은 DACUM 직무 분석기법을 활용하여 특성화고 산학일체형 도제교육을 위한 금형제작원 직무를 분석하는 것이다. 연구의 내용은 금형제작원의 직무를 구성하는 임무와 수행 작업을 도출하여 순서를 매기기한 후, 수행 작업별 중요도, 난이도, 빈도를 정하고 산업체에 취업할 당시 수행할 수 있는 최소한의 작업을 구분하여 제시하는 것이다. 최종적으로 직무분석 결과를 토대로 산학일체형 도제학교의 금형제작원 DACUM 차트를 개발하였다. DACUM 직무 분석을 위한 DACUM 위원회는 Level-I 라이센스를 취득한 DACUM 분석가 1명, 5년 이상 경력을 가진 데이컴 위원 9명, 서기 1명, 실무자 1명으로 구성하여 직무분석을 수행하였다. 연구 결과는 다음과 같다. 첫째, 산학일체형 도제학교의 금형제작원이란 설계된 도면에 따라 원자재와 부자재를 사용하여 가공기계와 공구로써 금형을 사상, 가공, 조립하는 자로 정의하였다. 둘째, 금형제작원의 직무 영역은 12개의 임무(duties)와 86개의 수행 작업(tasks)이 도출되었다. 12개 임무(금형 설계 검토, 원자 부자재 입고 확인, 사출 금형 가공, 가공품 완성 여부 확인, 사출 금형 래핑 습합, 조립 시 사출, 프레스 금형 가공, 프레스 금형 사상 조립, 다이 스포팅, 금형 트라이 아웃, 품질 육성, 금형 출하) 중에서 가장 많은 수행 작업을 도출한 임무는 '프레스 금형 사상 조립'으로 9개의 수행 작업이 확인되었다. 셋째, 각 작업마다 중요도, 난이도 및 빈도를 정도에 따라 각각 높음(A), 보통(B), 낮음(C)으로 구분하고, 전문가들의 합의를 통해 입직 초기에 갖추어야 할 핵심 능력인지의 여부를 구분하였다. 넷째, 직무 분석 결과를 토대로 산학일체형 도제학교의 금형제작원 DACUM 직무분석 차트를 개발하였다. 또한 금형제작원 직무에 종사하면서 필요한 일반 지식과 능력, 사용되는 공구, 기계, 자재 및 소모품의 목록을 끌어내고, 금형제작원의 장래 직업의 전망과 특성을 제시하였다.

• 대한기계학회논문집A
• /
• 제36권2호
• /
• pp.179-186
• /
• 2012

자동차 산업에서 대기오염을 줄이고 연비를 향상시키기 위해 경량화가 중요한 과제로 여겨지고 있다. 이를 위해 알루미늄 소재의 적용이 증가하고 있다. 판재를 차체에 적용하기 위해서는 주로 프레스 가공 공정을 거치게 된다. 이때, 재료, 제품설계 및 프레스 공정의 부적절한 가공 변수의 사용으로 인하여 파단, 주름, 및 스프링 백 등에 의한 다양한 형태의 가공 불량이 발생한다. 따라서 이들 변수들의 적절한 조화 뿐 만 아니라 엄격한 공정 관리가 요구된다. 이에 본 연구에서는 자동차 판재에 주로 사용되는 Al5454 재료에 대한 이론적으로 유도한 소성 불안정 조건을 구하고, MATLAB을 이용하여 성형 한계도를 도출하였다. 또한, 장출 인장 실험을 통해 얻어진 실험값과 이론적으로 도출한 성형 한계도와의 비교를 수행하였다.