• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2011.04a
• /
• pp.88-89
• /
• 2011

풍하중이 작용하는 교량의 응답을 구하기 위하여 RFA(Rational Function Approximation)와 같은 시간 영역해석법이 널리 사용되고 있다. 교량 단면의 공기역학적 특성을 정의하는 플러터 계수는 주파수 영역에서 정의되기 때문에, 시간 영역해석을 위하여 inverse Fourier transform을 통해 얻어진 impulse response function을 이용한 중첩 적분법이 제안되었다. 시간 영역해석을 위해서는 플러터 계수에 상관성이 존재해야 함을 밝히고, 최적화 방법을 이용하여 시간 영역 해석을 위한 플러터 계수 산정법을 제안하고자 한다. B/D=20의 구형 단면에 적용하여 제안한 방법의 타당성을 검증하고자 한다.

• Journal of Korean Association for Spatial Structures
• /
• v.4 no.1 s.11
• /
• pp.61-68
• /
• 2004

The wind tracker and structural monitoring system recorded wind and dynamic response data. The measured building is located in the moutatin in Sokcho. The damping ratio and natural frequency were analysed in this paper to obtain amplitude dependence. Amplitude dependent damping was showed clearly in the increasing rate of 9%. The tendency of dynamic properties of building obtained here are useful for the validation of dynamic properties of buildings in the evaluation of serviceability.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.4A
• /
• pp.507-515
• /
• 2008

In this study, a method predicting the displacement response of structures from the measured dynamic strain signal is proposed by using mode decomposition technique. Evaluation of bridge stability is normally focused on the bridge completed. However, dynamic loadings including wind and seismic loadings could be exerted to the bridge under construction. In order to examine the bridge stability against these dynamic loadings, the prediction of displacement response is very important to evaluate bridge stability. Because it may be not easy for the displacement response to be acquired directly on site, an indirect method to predict the displacement response is needed. Thus, as an alternative for predicting the displacement response indirectly, the conversion of the measured strain signal into the displacement response is suggested, while the measured strain signal can be obtained using fiber optic Bragg-grating (FBG) sensors. As previous studies on the prediction of displacement response by using the FBG sensors, the static displacement has been mainly predicted. For predicting the dynamic displacement, it has been known that the measured strain signal includes higher modes and then the predicted dynamic displacement can be inherently contaminated by broad-band noises. To overcome such problem, a mode decomposition technique was used. Mode decomposition technique estimates the displacement response of each mode with mode shape estimated to use POD from strain signal and with the measured strain signal decomposed into mode by EMD. This is a method estimating the total displacement response combined with the each displacement response about the major mode of the structure. In order to examine the mode decomposition technique suggested in this study model experiment was performed.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.23 no.5
• /
• pp.501-507
• /
• 2010

Structural optimization is performed to minimize the weight of a RC building structure, which has eight floors above ground and three underground, under gravity, wind, and seismic loads. Design optimization problem is formulated to find the values of the design variables that minimize the volume while satisfying various design and side constraints. To solved the optimization problem posed, several design techniques equipped in PIAnO, a commercial PIDO tool, are used. DOE is used to generate training points and structural analysis is performed using MIADS Gen, a general-purpose structural analysis CAE tool. Then, meta-models are generated from structural analysis results and accuracies of meta-models are evaluated. Next, design optimization is performed by using the verified meta-models and optimization technique equipped in PIAnO. Finally, we obtained optimal results, which could demonstrate the effectiveness of our design method.

• Journal of Korean Association for Spatial Structures
• /
• v.12 no.3
• /
• pp.97-104
• /
• 2012

In the design procedure of the cooling tower the form-finding of the shell is the most important process, because the shape of the shell determines the sensitivity of dynamic behaviour of the whole tower against wind excitation. In engineering practice, geometric parameters of the shell are generally determined based on natural frequency analysis. 32 cooling tower shell geometries were selected through variation of the geometric parameters of an existing cooling tower shell. They were evaluated based on the first natural frequency. From the result three representative cooling towers are selected for the analysis of the structural behaviour by means of linear FE-method. As a result, a hyperbolic rotational shell with the small radius overall will yield the shell geometry with a higher first natural frequency and thus a wind-insensitive structure.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.1
• /
• pp.174-182
• /
• 2014

To monitor the wind-induced responses of buildings, conventional real-time kinematic (RTK) methods based on two global positioning system (GPS) receivers (e.g., a reference and a rover) are widely applied. However, these methods can encounter problems such as difficulty in securing and maintaining a space for a reference station. With the recently developed virtual reference station (VRS)-RTK approach, the position of a structure can be measured using only a rover receiver. In this study, to evaluate the applicability of VRS-RTK methods in monitoring the lateral structural responses of frame structures, we performed free vibration tests on a one-story frame model (the first natural frequency of 1 Hz) and a three-story frame model (the first natural frequency of 0.85 Hz). To assess the reliability of the displacement and acceleration responses measured by the GPS, we performed a concurrent measurement using laser displacement sensors and an accelerometer. The accelerometer results were consistent with the GPS measurements in terms of the time history and frequency content. Furthermore, to derive an appropriate sampling rate for the continuous monitoring of buildings, the errors in the displacement responses were evaluated at different GPS sampling rates (5, 10, 20 Hz). The results indicate that as the sampling rate increased, the errors in the displacement responses decreased. In addition, in the three-story model, all modal components (first, second, and third modes) could be recorded at a sampling rate of 20 Hz.

• Journal of Korean Society of Steel Construction
• /
• v.9 no.2 s.31
• /
• pp.259-267
• /
• 1997

Wind tunnel test results and their interpretations focused on the behavior of girder, which were performed to study the aerodynamic stability of a self-anchored suspension bridge with lateral sag of main cable, are presented in this paper The shape of the girder which has the best aerodynamic stability was selected based on the section model test under uniform and turbulent flow conditions. Good performance of the selected section was confirmed in the full bridge model test. Measured flutter derivatives are presented for further study. Buffeting response was investigated to check the fatigue problem and serviceability of the bridge but it was found to be acceptable from the engineering point of view. Even though the drag coefficient of the girder had high value, the amplitude of the lateral vibration was found to be very low. This may be due to the restraint provided by the lateral sag of the cables.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.97-102
• /
• 2004

용액 중에서 나노입자의 전기영동 특성을 이용한 전자종이용 잉크 제조를 위해 $TiO_2$ 나노입자를 저유전율 용매인 cyclohexane에 혼합한 후 용매와 용질의 비중차를 줄이기 위해 분말 상 polyethylen을 첨가하여 high energy milling의 방법으로 입자분쇄와 동시에 입자 표면에 고분자 풍을 코팅하였다. 용액내의 입자 분산성 향상과 용매 착색을 위하여 계면활성제와 oil-blue N을 첨가한 후 전자종이용 잉크를 제조하여 측정한 제타 전위 결과 cyclohexane 내에서 $TiO_2$의 제타전위는 -40mV 정도였으나 polyethylene으로 코팅한 후 계면활성제를 첨가하였을 경우 최대 -110mV 이상의 높은 값을 나타내었다. 실제 디스플레이 특성을 평가하기 위해 포토리소그래피를 이용하여 3인치 크기의 ITO glass 위에 $10{\mu}m$의 크기를 갖는 십자형의 격벽을 $40{\mu}m$의 높이로 균일하게 형성한 후 합성된 전자잉크로 주입하여 상부전극과 하부전극사이에 UV 경화제를 도포하여 UV 접합을 실시하였다. 격벽 내에서 입자의 mobility를 측정하여 환산된 전자잉크의 응답속도는 0.1cm/sec로 측정되었으나, 전기영동시 입자들의 움직임에 따른 반사광의 파형을 측정한 경우 0.07cm/sec의 응답속도를 나타내었다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.29 no.1
• /
• pp.95-103
• /
• 2016

In this paper, aeroelastic instability and aerodynamic damping ratio of a helical $180^{\circ}$ model which shows better aerodynamic behavior in both along-wind and crosswind responses on a super tall building was investigated by an aeroelastic model test, and the aerodynamic damping ratio was evaluated from the wind-induced responses of the model by using Random Decrement Technique. Aerodynamic damping ratios evaluated in this study were verified through comparison with previous results obtained by quasi-steady theory. As a result, the aeroelastic instability of the helical $180^{\circ}$ model in crosswind direction were not occurred for any conditions with increasing the reduced wind velocity while the square model generally encounters aeroinstability due to the vortex shedding. The aerodynamic damping in along-wind direction for the helical $180^{\circ}$ and the square model increased monotonically both with reduced wind velocity, i.e., there is no relation with modifications of building shapes. On the other hand, in crosswind direction, the characteristics of aerodynamic damping ratio with reduced wind velocity for helical $180^{\circ}$ model were quit different from those of the square model.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.28 no.2
• /
• pp.92-100
• /
• 2016

Reliability analysis of tripod support structure for offshore wind turbine was performed. Extreme distribution function of peak response due to wind and wave loads was estimated by applying peak over threshold(POT) method. Then, stress based limit state function was defined by using maximum stress of support structure which was obtained by multiplying beam stress and concentration factor. The reliability analysis result was compared when maximum stress was calculated from shell element. Reliability index was evaluated using first order reliability method(FORM).