• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.124-124
• /
• 2017

Fe-Ni-Co 합금 박막(<$100{\mu}m$)을 황화물계 용액에서 전주공정으로 제조하였다. XRF로 측정한 박판의 평균 조성은 Fe-34 wt.% Ni-3 wt.% Co 이다. AFM으로 측정한 표면 조도는 35.2 nm 이다. 표면의 나노 경도는 평균 5.4 GPa 이었다. Oliver 모델을 적용한 구리 박막의 탄성하강강성도는 약 75 이었다. Alekhin 모델을 적용한 구리 박막의 마찰계수, 피로한계는 각각 0.134, 0.027 이었다. 유한요소법으로 평가한 Berkovich 형 나노압침선단의 하중분포를 이차원 선형 및 비선형 해석하면 1 [mN]의 정적하중을 가한 Fe-Ni-Co 박막은 약 576 [mN]로 예측되었다. 압침선단의 하중집중정도는 표면탐침현미경으로 관찰한 압흔의 변형정도와 유사한 경향을 보였다.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.17 no.6
• /
• pp.575-586
• /
• 2015

In NATM tunnel, the Ground-Lining Interaction model(GLI model) had been proposed a one of the numerical analysis as the ground load estimation method of the concrete lining. But this model was not applied with the interface mechanism between the ground and the support member or concrete lining. Therefor in this study, it is implemented as a model for closer than actual states that the interface element applied to the existing GLI model. And the modified GLI formula is proposed with the ground load estimation that is from the numerical results for each ground and rock cover conditions. Based on the numerical results, the ground load acting on concrete lining is reduced to ave. 88~106% in case of IV ground condition and ave. 47~57% in case of weathered soil condition comparing with the existing GLI model. It can be anticipated that the results obtained from this study can be applied to an estimation of the ground load on the concrete lining modeled like as real states, consistent and economical design.

• Journal of Korean Association for Spatial Structures
• /
• v.6 no.1 s.19
• /
• pp.83-90
• /
• 2006

The GF(Gust Factor) method is usually used as a method to evaluate equivalent static wind loads for general structures. The GF method is performed on the assumption that the shape of the equivalent static wind load profile is typically similar to that of mean wind loads. The shape of fluctuating wind loads could be quite different with that of the mean wind loads in case of large-span structures. So, the effect of higher modes as well as first mode must be considered to evaluate the wind loads. In this study, the ACS (Advanced Conditional Sampling) method is suggested to evaluate of equivalent static wind loads after investigating about GF and LRC method. The An method ran derive effective static wind loads by combining wind pressures and inertia forces of a structure chosen at a maximum load effect. The maximum load effect is assessed with the time history analysis using pressure data measured in wind tunnel tests. Equivalent static wind loads evaluated using ACS, GF, and LRC methods are compared to verify the effectiveness of ACS method.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.5
• /
• pp.25-33
• /
• 2012

In this study, gathered measuring data at fields constructed by IPS(Innovative Prestressed Support) system controls the ground displacement and improves the constructability of earth work and structure work greatly, and compared with horizontal displacement calculated by Elasto-plastic analysis program(EXCAV/W). As the result, displacement of calculated by pre-loading data is reduced 13.2% average of general method, and measuring displacement is also reduced 26.7% average of general method. Therefore that IPS system is more safe than conventional strut method in contrast to displacement of underground wall. In addition, horizontal displacement is reduced through the pre-loading effect used by IPS system.

• Fire Science and Engineering
• /
• v.29 no.4
• /
• pp.7-14
• /
• 2015

This study suggests basic data for fire-resistant compartments to prevent fires from spreading in a traditional markets. As representative combustible goods handled in traditional markets, bedding and bags were chosen. The fire loads could be calculated using the porosity of the materials based on a standard normal distribution. The bedding and bag porosity were 98.7%, and 94.39%, respectively. The the fire load of bedding is $29.9kg/m^2$, and that of bags is $65.61kg/m^2$.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.3
• /
• pp.116-126
• /
• 2010

The Korean rolling stock safety regulation stipulates that the collision deceleration of a car body should be maintained under average 5g and maximum 7.5g during train collisions. One-dimensional dynamic model of a full rake train, which is made up of nonlinear springs/bars-dampers-masses, is often used to estimate the collision decelerations of car bodies in a basic design stage. By the way, the previous studies have often used some average force-deformation curve for energy absorbing structures in rolling stock. Through this study, we intended to analyse how much the collision deceleration levels are influenced by the initial peak force modeling in the one-dimensional force-deformation curve. The numerical results of the one-dimensional dynamic model for the Korean High-Speed Train show that the initial peak force modeling gives significant effect on the collision deceleration levels. Therefore the peak force modeling of the force-deformation curve should be considered in one-dimensional dynamic model of a full rake train to evaluate the article 16 of the domestic rolling stock safety regulations.

• Journal of the Korean Society for Railway
• /
• v.13 no.1
• /
• pp.31-36
• /
• 2010

The objective of this study is to evaluate effects of honeycomb cell size for compressive behaviors of square sandwich composite tubes with woven fabric carbon/epoxy skin and Al honeycomb core. In order to achieve these goals, four different kinds of tubes were fabricated and compressed to 200mm~250mm under quasi-static load of 10mm/min. The Al honeycombs with cell size of 6.35mm and 9.53mm were used. The relationship of mean compressive load and cell size was evaluated. In addition, the effect of peel strength and equivalent elastic modulus in ribbon direction for the mean compressive load was investigated.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.13 no.1
• /
• pp.47-52
• /
• 2010

The wave energy absorption efficiency and the first-order and the time-mean second-order wave loads of a three-dimensional bottom-mounted oscillating water column (OWC) chamber structure are studied. The potential problem is solved by making use of a hybrid Green integral equation associated with the finite-waterdepth free-surface Green function outside a twin chamber and the Rankine Green function inside taking account of the fluctuating air pressure inside the chamber. Numerical results of the primary wave energy converting efficiency and the oscillating and steady wave loads of a three-dimensional bottom-mounted OWC pilot plant have been presented.

• Computational Structural Engineering
• /
• v.10 no.4
• /
• pp.239-249
• /
• 1997

The method to distinguish chaotic attractors in the perturbed response behaviors of a piecewise-linear system under combined regular and external randomness is provided and examined. In the noisy fields such as the ocean environment, excitation forces induced by wind, waves and currents contain a finite degree of randomness. Under external random perturbations, the system responses are disturbed, and consequently chaotic signatures in the response attractors are not distinguishable, but rather look just random-like. Mean Poincare map can be utilized to identify such chaotic responses veiled due to the random noise by averaging the noise effect out of the perturbed responses. In this study, the procedure to create mean Poincare map combined with the direct numerical simulations is provided and examined. It is found that mean Poincare maps can successfully distinguish chaotic attractors under stochastic excitations, and also can give the information of limit value of noise intensity with which the chaos signature in system responses vanishes.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.4
• /
• pp.93-101
• /
• 2008

Bearing strength test was investigated to determine the bearing properties of domestic larix glulam according to the load direction (in parallel to grain and in perpendicular to grain), the fastener (bolt and drift-pin), and the direction of laminae. The specimen was 5 ply glulam. The diameters of fastener are 12, 16 and 20 mm. The results were as follows. 1) In according to the diameter of bolt and drift-pin, the average of maximum bearing strength in parallel to grain loading was similar to that in perpendicular to grain loading. The average of maximum bearing strength was 1.50~2.31 times higher in parallel to grain loading than in perpendicular to grain loading. The average of maximum bearing strength in parallel to grain loading was lowered by 20% with increasing the diameter from 16 mm to 20 mm, but that in perpendicular to grain loading didn't show a clear tendency. 2) The average of bearing stiffness in parallel to grain loading was the highest at 16 mm in diameter. The average of bearing stiffness is similar to the shearing stiffness in drift-pin connection with increasing diameter. 3) In parallel to grain loading, the failure mode of specimens was the splitting along the grain in decreasing diameter. The failure mode in perpendicular to grain loading was the splitting along the grain. In this case, split occured more in specimens using bolt than in those using drift-pin. 4) The 5% offset yield strength in parallel to grain loading was similar to the predicted bearing strength of KBCS, NDS. In perpendicular to grain loading, the NDS's equation can be applied to predict the bearing strength.