• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.10
• /
• pp.6322-6328
• /
• 2014

Finite element analyses were performed to find out the load bearing behavior of three kinds of shallow foundations. The analysis results for strip footing showed that local shear failure mode could be observed for a zero dilatancy angle and general shear failure mode could be seen for non-zero dilatancy angles. The ultimate bearing loads for non-zero dilatancy angles were approximately 1.5 times higher than that of a zero dilatancy angle. General shear failure mode was observed for circular footing and square footing regardless of the dilatancy angle. The ultimate bearing loads for a non-zero dilatancy angle were slightly greater than that for a zero dilatancy angle. A comparison of the load-settlement curves for three kinds of footing showed that the load bearing capacities for non-zero dilatancy angle were greater than those for a zero-dilatancy angle.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.1
• /
• pp.49-63
• /
• 2014

Bearing capacity factor $N_{\gamma}$ and shape factor were studied for rigid strip and circular footings with a rough base on sand by numerical modelling considering the effect of dilation angle. The numerical model was developed with an explicit finite difference code. Loading procedures and interpretation methods were devised in order to shorten the running time while eliminating the exaggeration of the reaction caused by the explicit scheme. Using the Mohr-Coulomb plasticity model with associated (${\psi}={\phi}$) and nonassociated (${\psi}$ < ${\phi}$) flow-rules, the bearing capacity factor $N_{\gamma}$ was evaluated for various combinations of internal friction angles and dilation angles. Bearing capacity factor decreased as the dilation angle was reduced from the associated condition. An equation applicable to typical sands was proposed to evaluate the relative bearing capacity for the nonassociated condition compared to the associated condition on which most bearing capacity factor equations are based. The shape factor for the circular footing varied substantially when the plane-strain effect was taken into account for the strip footing. The numerical results of this study showed closer trends with the previous experimental results when the internal friction angle was increased for the strip footing. Discussions are made on the reason that previous equations for the shape factor give different results and recommendations are made for the appropriate design shape factor.

• Aerospace Engineering and Technology
• /
• v.9 no.1
• /
• pp.17-27
• /
• 2010

KSLV-I KM plume including alumina particle has been studied using the continuum solver. Alumina particles are assumed to have 7 different diameters, and the specific ratio of the plume gas is assumed to be 1.2, with which the internal nozzle flow characteristics are similar to those of the chemically equilibrium analysis results. The results showed that the expansion angle of the particles is smaller than that of the gas phase, and that the big sized alumina particles are gathered in the plume core and the expansion angles of the big sized particles are smaller than those of the light particles. When the emissivity of the particles are assumed to be 0.1, the radiative heat flux is equivalent to those measured during the flight test of KSLV-I.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.4
• /
• pp.301-315
• /
• 2001

본 연구에서는 최근 5년간 국내 각 지역에서 채취한 802개의 절리면 시료에 대하여 전단시험을 실시하여 얻은 결과를 이용하여, 절리면의 여러 공학적 성질들을 조사, 연구하였다. 절리면 전단시험에서 얻어진 최대마찰각 및 잔류마찰각을 지체구조별, 암종별로 분류하고 통계적으로 구하였으며, Barton의 전단강도식의 입력변수인 JRC, JCS를 측정하고 Barton식의 적용성에 대해서도 검토하였다. 그 결과 설계의 기초자료로 활용할 수 있는 지역별, 주요 암종별 최대마찰각, 잔류마찰각을 제시하였다. 또한, JRC, JCS, 수직응력에 따른 마찰각과 전단강성 및 팽창각의 변화를 분석하였다. 마지막으로, Barton의 식에서 구한 이론적 전단강도와 이 실험에서 얻어진 전단강도를 비교한 결과, Barton의 경험식은 높은 상관도로 암석 절리면 전단강도를 예측할 수 있음을 확인하였다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1999.10a
• /
• pp.32-32
• /
• 1999

초음속 과소 팽창 제트가 경사진 평판에 충돌을 하게 되면 평판의 표면과 노즐출구에서 팽창된 자유제트(Free jet)와의 상호 간섭으로 인해 매우 복잡한 유동 구조가 형성된다. 예를 들면, 수직평판에서 발생되는 판 충격파(Plate shock)는 경사평판에서는 Upper plate shock, Lower plate shock, Intermediate plate shock과 같이 여러 형태로 발생되어 평판에서의 압력분포에 있어 수직일 경우와 다소 다른 경향을 보여준다. 본 연구의 주요 목적은 평판의 경사각을 변화시킬 때 평판 표면에서의 복잡한 유동 현상을 이해하는데 있다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.10a
• /
• pp.113-118
• /
• 2004

Experiments are conducted to get basic information of under-expanded impinging jet in the near field. Experimental parameters are impinging angle and under-expanded ratio. As the under-expanded ratio increases, the maximum surface pressure decreases and the reducing effect of recovery factor increases. As the impinging angle decreases, the peak of surface pressure is displaced slightly from the geometric center of the plate to the upward region and the cooling region is expanded in the downward region, whereas it is contracted in the upward region.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.329-334
• /
• 2009

The Study of steady performance of orifice must be precede before study of dynamic characteristics with configuration change. So, orifice performance with change of diameter ratio, thickness, expansion and angle predicted by CFD. The analysis algorithm is SIMPLEC. And PRESTO, QUICK scheme is used for dicretization. The $k-{\omega}$ STS turbulent model also used. The discharge coefficient is rapidly increased with increasing of diameter ratio and slowly decreased after rapidly increasing with orifice thicken. In case of expansion angle, the discharge coefficient is the smallest at $45^{\circ}$ of the angle.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.2
• /
• pp.85-91
• /
• 2005

This paper investigates P-S (load-settlement) relationship for the end-bearing Pile in granular material using the CRISP FE Program with the laboratory 2D model pile load test. In order to simulate the effect of end-bearing pile problem in the FEA, the author adopts several forms of slip element around the pile length and the pile tip. Through this study it was found that e degree of non-associated Plastic flow rule incoporated into the Mohr-Coulomb model for the end-bearing pile with the slip elements was a dominant factor in terms of numerical solution convergence. In contrast, the roller boundary used along the pile shaft showed a smooth convergence with respect to the degree of non-associated plastic flow rule.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.11a
• /
• pp.556-559
• /
• 2006

벌크형태의 태양전지 기판을 대체할 목적으로 연성기판을 적응한 태양전지 개발이 활발하게 진행되고 있으며, 주재료는 플라스틱 기판, 금속기판 등이 있다 그러나 기존의 연성기판인 플라스틱의 경우 열과, 내구성, 화학약품에 약하다는 단점이 있으며, 금속기판은 높은 생산원가, 박막화의 어려움 등의 문제를 안고 있다 이러한 문제를 극복하기 위해 전주성형법으로 제조된 철-니켈계 연성기판을 개발하였다. 이 연성기판의 경우 고온의 공정조건에서도 열팽창율이 플라스틱 기판보다 낮으며, 기존의 금속기판 보다 저렴한 생산단가로 쉽게 극박화 할 수 있다는 것이다. 전주성형법을 적용하여 40Ni, 45Ni, 52Ni 연성기관을 제조하였으며, TMA 장비를 사용하여 각 연성기판의 열팽창 계수를 측정한 결과 6.36, 6.78, $10.93{\mu}m/m^{\circ}C$로 기존의 연성기판인 플라스틱, 금속에 비해 낮은 열팽창 계수를 가짐으로서 고온 공정 중에 안정성 요구를 충분히 충족시킬 수 있다.

• Tunnel and Underground Space
• /
• v.26 no.5
• /
• pp.384-395
• /
• 2016

Both the roughness measurement tests and the multi-stage shear tests were carried out on the 110 rock joint samples in order to investigate the influences of rock type, joint roughness and normal stress on the shear behaviour of rock joints. Test samples were composed of quartz porphyry, dacite, granite and gneiss, which were classified into three detailed groups according to their JRC values. Roughness parameters of rock joints were analyzed by roughness measurement tests, and shear characteristics were also investigated by multi-stage shear tests. Both peak shear strength and shear stiffness were increased as both joint roughness and normal stress were increased, whereas dilation angles showed lower values at the lower roughness and higher normal stress conditions. Besides, shear characteristics obtained from all tests of four different rock types with different rock strengths showed irrelevant details, therefore the influences of both joint roughness and normal stress on shear behaviors were found to be more considerable than the strength of intact rock. The results obtained from both multi-stage shear tests and direct shear tests were finally compared, where the dilation angles obtained from multi-stage shear tests were found to be valid only for the first normal stress conditions.