Proceedings of the Korean Institute of Navigation and Port Research Conference
/
2011.06a
/
pp.340-342
/
2011
묘박 중인 선박은 주묘를 예방하기 위해서는 파주력을 크게 유지해야 하는데, 대부분의 파주력은 앵커에 의해 형성된다. 앵커의 파주력은 앵커의 형태와 수중무게 그리고 해저 저질에 따른 파주계수에 따라 달라진다. AC-14형 앵커는 ASS형 앵커에 비하여 2~2.5배의 파주력을 형성하는 것으로 알려져 있다. 그러나 이러한 파주계수는 모형실험 등을 통하여 정해진 것으로 실제 상황에서 그 유효성을 분석한 연구는 거의 없다. 따라서 본 논문에서는 AC-14형 및 ASS형 앵커의 파주계수를 실제 선박에서의 주묘 사례를 분석하여, 현재 사용되고 있는 파주계수의 유효성을 확인하였다.
Journal of the Korean Society of Fisheries and Ocean Technology
/
v.27
no.2
/
pp.97-104
/
1991
Generally, the coefficients of common holding power of an anchor and a chain cable have been reported too higher in their values in the safety of the shiphandling. The model experiment was carried out to find the most suitable coefficients of holding power of the Hall's type anchor and the chain cable in various kinds of seabed. The results obtained are summarized as follows; 1) The coefficients of holding power of the anchor and the chain cable were 4.05, 0.75 in the mud, 3.95, 0.66 in the sand and 3.61, 0.72 in the pebbles respectively. 2) The experimental coefficients of holding power of the anchor and the chain cable were 0.4~0.6 times the values of the coefficients of common holding power. They were almost same as the values of the coefficients of safe holding power in the mud and the sand, but in case of the pebbles, they were 1.4~1.8 times the values of the coefficients of safe holding power. 3) It is considered useful for the safety of the shiphandling to draw curves of the holding power with maximum limits holding power at the various wind forces and the coefficients of holding power.
Vessels on anchoring are sometimes dragged due to the increased external forces. For preventing the dragging, it is required to enhance the holding power of the anchor. The holding power depends on the type and weight of the anchor and the seabed condition. Especially, the holding power of AC-14 type anchor is known to be 2~2.5 times bigger than that of ASS type anchor. However, these coefficients was determined nearly by the result of the model test, so there is a need to verify that by sea trial. Therefore actual dragging case was analyzed and then compared with the coefficients in use, it was found that the two of them are much alike.
In this study, with the awareness of the limitations set in the currently operated calculations of holding power and the holding power coefficient of anchors of naval ships due to its simple application of a specific value, various factors that impact the holding power and its coefficient were verified based on existing data analysis of literature research and numerous experiment results from anchor manufacturers, research institutes and academic community in order to overcome the aforementioned limitations. In addition, holding power and holding power coefficient were compared and analyzed by the shape of anchors. As a result, we came to know that the holding power of AC-14 type anchor is stronger than that of ASS type anchor or U.S. Navy Standard type anchor which makes it possible to reduce the weight of the anchor and therefore ease the process of naval shipbuilding. Furthermore, we confirmed the fact that U.S. Navy Standard type anchor does not react sensitively to the weight change of the anchor. Lastly, we found out that Danforth type anchor's holding power coefficient is in inverse proportion to the weight. Moreover, instructions for managing anchor are arranged easily for your information. The results of this study is expected to provide anchor - operating naval crew with a reliable theoretical basis pertaining to an anchor's holding power and its coefficient and contribute much for the safety of their act of anchoring.
Proceedings of the Korean Institute of Navigation and Port Research Conference
/
2013.06a
/
pp.23-24
/
2013
본 연구에서는 해군함정에서 투묘 시 함정별 묘의 파주계수와 그에 파주력 그리고 외력의 세기를 고려한 묘쇄의 적정 신출량을 구할 수 있는 수리모델을 정립하여 제시하고, 이것을 해군이 보유하고 있는 전 함정 승조원들로 하여금 쉽게 사용할 수 있는 적정 묘쇄 신출량을 그래프한 자료를 제시하였다. 본 연구 결과는 해군함정이 투묘시 바로 적용될 수 있을 뿐만 아니라, 이론적인 근거를 제공하는 참고자료로 유용하게 활용될 수 있을 것이다.
The vessel should prevent dragging anchor against the external forces by utilizing the anchor and secure the stability of it. A fundamental understanding on the embedding motion and holding power of the anchor is necessary to perform the safe operating of anchor work. In this study, the embedding motion and holding power of the anchor according to an initial position in an experimental tank of 6m long in sand are tested by using two types of different anchor models(ASS and AC-14), which are generally applied to the commercial vessel nowadays. The anchor flukes seem to rotate and to be embedded into soil up to the maximum depth and maintaining a constant depth in case of the same direction and perpendicular to the towing direction, regardless of the form of an anchor. In case of the opposite direction to the towing direction, it is noted that the coefficient of holding power becomes smaller than the other initial positions.
Journal of the Korean Society of Fisheries and Ocean Technology
/
v.37
no.2
/
pp.95-105
/
2001
A series of experiment is carried out to determine the holding power of the existing anchors used in the stationary gear in the coast of the South sea. The experiment apparatus is made of the pulling machine, the load cell, the personal computer and three water tanks the bottom of which are mud, sand and m & s respectively. The result obtained are as follows : 1. On the tension and holding power of the existing anchors, B-type of the stock anchor with two fluke shows the greatest and gets smaller on order of A-type one with a fluke. The holding power of the anchors shows the greatest in the mud and gets smaller in order of m & s, sand. And, the holding power depending upon the length of anchor rope increase as the length does up to the 4 times of depth. 2. On the holding power per fluke area of the existing anchors in case of ration of length of anchor rope to depth is 2, 3 and 4, A-type anchor shows about 310-320 kg/m supper(2), 470-480 kg/m supper(2), 590-640 kg/m supper(2) respectively, B-type one 260-265 kg/m supper(2), 390-450 kg/m supper(2), 630-700 kg/m supper(2) respectively, and C-type one 70-100 kg/m supper(2), 150-180 kg/m supper(2), 210-270 kg/m supper(2) respectively. The holding power per fluke area of the anchors increase as the length of anchor rope does. 3. On the coefficient of holding power of the existing anchors, A-type anchor shows the greatest and gets smaller in the order of B-type one, C-type one.
Proceedings of the Korea Water Resources Association Conference
/
2019.05a
/
pp.102-102
/
2019
토양수분은 수문 및 기상 현상의 주요 요인으로 가뭄, 홍수 및 범람과 같은 자연 재해와 관련이 깊은 인자이다. 이러한 토양수분의 관측 기술 중 위성 데이터를 활용한 원격탐사 기술은 광범위한 지역의 관측이 용이하고 지점이 아닌 공간 데이터를 제공하는 장점을 지니고 있어 토양수분의 관측에 유리하다. 특히 높은 해상도의 위성기반 토양수분 데이터는 토양수분의 변동성이 큰 지역의 수문, 기상학적 현상을 보다 자세히 분석할 수 있게 해주며 가뭄 및 범람과 같은 수자원 관련 재해를 정확하게 분석하는데 요구된다. 이로 인해 최근 Sentinel-1 위성에서 운용중인 Synthetic Aperture Radar(SAR) 데이터를 이용한 매우 높은 공간해상도(10m~1km)를 지니고 있는 토양수분데이터 생산에 관한 연구가 세계적으로 활발히 진행되고 있다. 그러나 국내에서는 Sentinel-1 위성을 이용한 토양수분 데이터 복원에 관한 연구가 미비한 실정이다. 따라서 본 연구에서는 파주 감악산 설마천 유역에서의 Sentinel-1 위성의 SAR 데이터를 이용한 고해상도 토양수분 데이터를 복원하고자 한다. 파주 설마천 유역은 감악산 일대로 경사가 심하고 식생이 두터운 산악지형이다. SAR를 이용하여 산지에서 신뢰성 있는 토양수분 자료를 복원하기 위해서는 가장 큰 오차의 원인으로 작용하는 경사와 식생을 고려하여야 한다. 먼저 표면 경사의 영향의 경우 SAR 센서의 레이더 입사각과 수치 표고 모델을 이용하여 고려하고자 한다. 다음 과정으로 표면 경사가 고려된 Sentinel-1 데이터의 후방산란계수와 Landsat-8 데이터 및 지점 토양수분 데이터를 이용하여 식생에 따른 후방산란계수의 거동을 Water Cloud Model을 이용하여 분석하였다. Water Cloud Model은 토양위의 식생의 수분이 후방산란계수에 혼동을 주는 구름과 같이 작용한다고 가정하고 식생수분을 후방산란계수와 레이더 입사각 및 식생지수를 통해 계산하는 모델이며 이를 이용하여 토양수분 복원에 있어 식생의 영향을 제거하고자 하였다. 이를 통해 식생과 표면 경사를 고려하여 복원된 토양수분 데이터를 설마천 유역의 지점 데이터와 비교 분석하고 다른 위성기반 토양수분 데이터 및 강우 데이터를 이용하여 평가하였다. 본 연구결과를 통해 한반도 산지에서의 SAR 데이터를 이용한 토양수분 복원 기술의 기초가 마련될 것이며 이를 통해 산지가 대부분인 한반도의 토양수분 거동을 이해하는데 유용한 자료를 제공할 수 있을 것으로 기대된다. 본 연구 이후에는 연구결과분석을 통한 산지에서의 고해상도 토양수분 복원 알고리즘을 분석, 보완하고 한반도에서의 SAR 기반 토양수분 데이터의 정확도를 높이는 연구가 진행되어야 할 것이다.
Journal of the Korean Society for Marine Environment & Energy
/
v.15
no.4
/
pp.357-362
/
2012
Despite the Wave observations data is very important information to human life at sea, the technology development and research for wave equipments are lacking. In this study, the wave observation system using GPS was evaluated the quality of wave observation data by comparing of long-term observations. The result of the comparison of the acceleration sensor (Hippy-40) and GPS sensor (Mose-1000), the correlation coefficient of the significant wave height and significant wave periods is 0.997 and 0.990 respectively. Also in case of BIAS, the significant wave height is 0.014 m, the significant wave period is -0.212 sec. It makes no significant differences whether the acceleration sensor (Hippy-40) and GPS sensor (Mose-1000). These results of the wave observation data using GPS quality will be evaluated as very good.
Proceedings of the Korea Water Resources Association Conference
/
2023.05a
/
pp.323-323
/
2023
유역의 증발산량 자료는 물순환 과정을 규명하는 매우 중요한 자료 중의 하나이며, 물순환 성분별 명확한 산정 결과는 수자원 개발과 물환경 보전에 중요한 정보를 제공할 수 있다. 본 논문에서는 임진강 유역(유역출구(한강합류점) 기준, 유역면적 8,138.9km2)을 대상으로 5개년(2018~2022) 기상관측자료를 이용하여 증발산량을 산정하였으며, 그 외의 수문관측자료를 통해 물수지 분석도 수행하였다. 증발산량 산정은 세계식량기구(FAO)에서 제시한 Penman-Monteith equation을 적용하여 일별증발산량을 산정하였으며, 작물의 종류에 따른 계수는 잔디의 경우를 채택하였다. 본 방정식을 통해 산정된 증발산량(ETo)은 기준작물에 수분의 공급에 제한이 없는 상황에서 산정된 기준 증발산량(reference evapotranspiration)을 의미하며, 기준 증발산량을 실제 증발산량으로 변환하기 위해서는 작물계수를 고려해야 한다. 작물계수는 식생의 높이, 알베도, 식생의 저항, 토양으로부터의 증발 등의 영향을 받게 되나, 더욱더 명확하게는 식물에서의 증산을 설명하는 기본 작물계수와 토양에서의 증발을 설명하는 토양계수의 합을 통해 계수를 산정하게 된다. 임진강 유역에 공간적으로 분포된 작물계수를 정확히 산정하기에는 한계가 있으므로 잔디의 경우로 한정하여 산정된 기준 증발량은 833.0mm(5개년 평균값)이다. 각 물순환 성분별로 생성된 임진강 유역의 5개년 평균값인 유역평균강우량은 1,412.9mm이며, 하천유출량은 804.9mm(유역평균강우량 대비 57.0%), 실제 증발산량은 442.3mm(유역평균강우량 대비 31.3%, 기준 증발산량 대비 약 53.0%), 유역저류량은 165.7mm(유역평균강우량 대비 11.7%)이다. 유역평균강우량은 8개 관측소(양덕, 원산, 신계, 개성, 평강, 철원, 동두천, 파주) 강우량의 유역평균값이며, 하천유출량은 유역출구의 상류 관측소인 비룡대교 관측소(유역면적 6,784.0km2) 유출량의 유역면적비 적용값이다. 실제 증발산량은 기준 증발산량 산정값에 해당 유역내 존재하는 설마천 유역의 기준 증발산량과 실제 증발산량 비율(약 53.0%)을 적용한 값이며, 유역저류량은 전제적인 물수지 분석을 통해 얻어진 추정값이다. 이와 같이 산정된 물순환 성분별 자료는 유역의 물순환 과정 규명을 위한 기초자료로 매우 유용하게 활용될 수 있으며, 유역 물관리를 위한 의사결정 과정에 중요한 역할을 할 수 있을 것으로 기대된다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.