• Journal of Environmental Science International
• /
• v.8 no.1
• /
• pp.45-50
• /
• 1999

Four cast iron pipe sections containing 3 styrene butadiene rubber (SBR) gaskets (1 joint and 2 end caps) were filled with water and maintained at approximately 40 psi internal pressure. The pipe sections were placed inside 16 gallon drums filled with initially clean sand. Three of the tanks were subsequently contaminated with gasoline, gasoline spiked with pyrene and naphthalene, and toluene. The forth tank served as a control. The water inside each pipe was monitored over time for organic chemical contamination. Permeation of organic chemicals into the water inside the pipe systems was found to occur in all 3 contaminated pipe systems after approximately 100 days as measured organic chemicals concentrations were significantly above those in the uncontaminated cell. Flushing experiments in which the water inside the contaminated pipes was replaced with initially clean water showed that organic chemical concentrations inside the pipe rapidly (12 days) reached their preflushing levels.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2009.05a
• /
• pp.651-655
• /
• 2009

본 연구에서는 컷 집합(cut set)개념과 파이프의 부정류를 위한 수치해석 결과를 이용하여 상수관망의 불능 확률을 정량적으로 산정하는 신뢰성 해석이 수행되었다. 특히 상수관망에서 중요한 운용형태의 하나인 밸브의 개폐효과에 따른 효과를 통하여 불능확률이 산정되었다. 먼저 부정류 수치해석을 위해서 작은 상수관망을 만들고 여러 가지 시나리오를 재현하였다. 이때 부정류 해석을 위해서 특성선법(the method of characteristics)모형이 사용되었다. 밸브의 개폐에 따라서 여러 가지 형태의 부정류가 발생되고 발생된 부정류를 상수관망의 불능확률을 크게 증가시킨다. 상수관망에서 컷 집합을 추출하여 기준지점에 배출유량(demand)가 도달하지 못할 확률을 불능확률로 규정하여 정량적으로 산정한다. 이를 위해서 컷 집합의 총 유량을 시간에 따라 평균하여 COV를 불능확률 산정에 이용한다. 부정류로 인한 파이프 유량의 변동이 심할수록 COV는 증가하고 결국은 컷 집합의 불능확률은 증가하게 된다. 그리고 똑같은 상수관망에 에너지 감쇠장치인 조압수조가 설치되어 부정류 압력파(pressure wave)를 크게 감소시켰을 때 불능확률을 비교하였다. 조압수조와 같은 압력감쇠장치가 상수관망의 부정류 효과와 불능확률을 크게 저감시키는 것을 알 수 있었다. 또한 신뢰성 해석 결과로부터 부정류가 불능확률을 급격히 증가시킨다는 것을 확인하였다. 따라서 부정류 효과를 고려한 신뢰성 해석은 상수관망의 운용, 관리, 감독, 그리고 설계와 계획을 위해서 필수적이라 할 수 있다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.12
• /
• pp.1079-1085
• /
• 2010

A steady-state analytical model was presented for a loop heat pipe (LHP) with an evaporator that has a flat geometry. On the basis of a series of reviews of the relevant literature, a sequence of calculations was proposed to predict the temperatures and pressures at each important part of the LHP: the evaporator, liquid reservoir (compensation chamber), liquid line, vapor line, and condenser. The analysis of the evaporator, which is the only part in the LHP that has a capillary structure, was emphasized. Thin-film theory is applied to account for the pressure and temperature in the region adjacent to the liquid-vapor interface in the evaporator. The present study introduced a unique method to estimate the liquid temperature at the interface. Relative freedom was assumed in the configuration of a condenser with a simplified liquid-vapor interface. Our steady-state model was validated by experimental results available in the literature. The relative error was within 3% on the absolute temperature scale, and reasonable agreement was obtained.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.2
• /
• pp.414-421
• /
• 2022

Subsea oil and gas exploration is increasingly moving into deeper water depths, and typically, subsea pipelines operate under high pressure and temperature conditions. Owing to the difference in these components, the axial force in the pipe is accumulated. When a pipeline is operated at a high internal pressure and temperature, it will attempt to expand and contract for differential temperature changes. Typically, the line is not free to move because of the plane strain constraints in the longitudinal direction and soil friction effects. For a positive differential temperature, it will be subjected to an axial compressive load, and when this load reaches a certain critical value, the pipe may experience vertical (upheaval buckling) or lateral (snaking buckling) movements that can jeopardize the structural integrity of the pipeline. In these circumstances, the pipeline behavior should be evaluated to ensure the pipeline structural integrity during operation in those demanding loading conditions. Performing this analysis, the correct mitigation measures for thermal buckling can be considered either by accepting bar buckling but preventing the development of excessive bending moment or by preventing any occurrence of bending.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.7
• /
• pp.947-952
• /
• 2010

Components such as pressure vessel, hydraulic hose assembly, accumulator, hydraulic cylinder, hydraulic valve, pipe, etc., are tested under the impulse-pressure conditions prescribed in ISO and SAE standards. The impulse pressure test machine needs to have a high pressure, a precise control system and a long life. It should satisfy the requirements for fabrication of the impulse tester to generate ultra high pressure in the hydraulic system. In the impulse tester, a servo-valve control system is adopted; although the control application is convenient, it is expensive owing to the cost of developing the system. The type of the control system determines the pressure wave, which affects the components that are tested. In this study, the manufacturing process and the intensifier system design related to the flow, pressure, and the increasing rate of pressure are investigated. The results indicate the ultra high pressure waves in the system.

• Journal of Animal Environmental Science
• /
• v.9 no.2
• /
• pp.69-78
• /
• 2003

In this study, the energy conversion equipment from the radiation energy to mechanical energy by using n­pentane as the operating fluid was constructed and the performance to pump the water was tested for the utilization of solar powered water pump. The equipment was designed optimally, after the theoretical analyses of the water pumping head and water quantity per cycle were done. The pentane vapour temperature in the condenser and the temperature of the outlet water from the condenser became lowered and the heat transfer rate became higher with decreasing the water inlet level to the condenser. The temperature difference between the condenser and the water tank was significant. Therefore, the distance between the water tank and condenser was recommended to be shorten and the diameter of their connecting pipe was recommended to be narrow in order to reduce the resistance of the fluid passage and improve the heat transfer rate. The amount of water pumped was 1.6­2.4 liters. Mass flow rate of the cooling water became lowered when the cooling water pipe was prolonged from the condenser to improve the heat transfer rate.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.3
• /
• pp.201-205
• /
• 2015

This paper describes thermal flow characteristic in various pipelines: straight pipeline and curved pipeline. In the Arctic and ocean area, pipelines are exposed to a extremely low temperature ($0{\sim}-40^{\circ}C$). In this situation, three-dimensional flow analysis should be analyzed to investigate thermal effects such as pressure drop, temperature change, velocity deficit and distribution change of liquid droplet of internal fluid. Also, due to freezing of water droplet, impingement erosion is expected in the curved pipeline. The stability of the pipelines can be influenced by impingement erosion. In this paper, multi-phase and multi-species analysis was introduced to analyze the flow characteristics and impingement erosion of Arctic and ocean pipelines.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.714-717
• /
• 2017

Among the factors considered in the design stage of a space launch vehicle using liquid propellant, research has been focused out on the pogo phenomenon, longitudinal dynamic instability. The pogo phenomenon refers to the instability that the longitudinal vibration of the launch vehicle structure causes a change in the pressure and flow rate of the fluids in propulsion system, and this change re-excites the fuselage structure. This mechanism constitutes a closed system to gradually increase the vibration of the launch vehicle. This paper specifically focuses on the dynamic analysis of pressure and flow changes in the propulsion system. Based on the example study of the space shuttle, the acoustic modal analysis of the propulsion system is performed to predict the modes of the supply line causing instability of the fuselage.

• Journal of Energy Engineering
• /
• v.12 no.1
• /
• pp.17-22
• /
• 2003

The present study was conducted to obtain the fundamental knowledge on the manufacturing and operating characteristics of a small scale CPL (Capillary Pumped Loop) heat pipe. CPL heat pipes are able to transfer heat effectively at any orientation in a gravitational field over long distances. An experimental model with an evaporator of a circular plate shape was designed and manufactured and its operating performances were tested. A Bronze powder sintered metal plate of 3 mm thick and $\Psi$ 50 mm was used as wick and ethanol was used as working fluid. An experimental apparatus was set up to ascertain the operating conditions oi CPL at different heat load and an surrounding temperature at the condenser was maintained about 13$^{\circ}C$.

• Journal of Korea Water Resources Association
• /
• v.42 no.10
• /
• pp.785-793
• /
• 2009

Numerical model which can simulate the surge tank for unsteady flow was developed in the present study. Furthermore, reliability model which can calculate the probability of pipe breakage regarding unsteady effect was developed. For the risk estimation of pipe breakage and functional estimation of surge tank, probability of pipe breakage for pipe network with surge tank was calculated regarding unsteady effect. From the results, it was found that unsteady flow significantly increase the probability of pipe breakage and surge tank considerably decrease probability of pipe breakage as damping out the pressure oscillations.