• Nuclear Engineering and Technology
• /
• v.17 no.3
• /
• pp.211-215
• /
• 1985

The effects of temperature and strain rate on the I-SCC behaviors of Zircaloy-4 were investigated by constant load test at 30$0^{\circ}C$ and constant elongation rate test at 300, 350 and 40$0^{\circ}C$ in 3.34mg $I_2$/㎤. The results showed that I-SCC susceptibility increased as the strain rate decreased or the temperature increased. The empirical relation between the stress and the time to failure at 30$0^{\circ}C$ was given by 1/ $t_{f}$∝exp (0.3$\sigma$/$\sigma$$_{UTS}$-31.5) When the I-SCC susceptibility was expressed by the ratio of fracture energy in iodine atmosphere to that in the inert atmosphere, severe I-SCC susceptibility was found near 7.6$\times$10$^{-6}$ sec at 30$0^{\circ}C$ and the maximum point of I-SCC susceptibility tended to shift to the higher strain rate with increasing the temperature. The quasi-cleavage fracture was observed in I-SCC fracture surface. From these results, it was certain that the film repture step was involved as an important process in the I-SCC mechanism of Zircaloy-4.4.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.5 no.2
• /
• pp.59-64
• /
• 2001

The purpose of this work is to investigate the static strength, the stress distribution, and the failure process of quasi-isotropic composite laminates made of two different matrices when loading directions are changed. We carried out static tests of $[0/-60/+60]_s$ and $[+30/-30/90]_s$ laminates. Two types of matrices used are AS4/epoxy and AS4/PEEK. The damage mechanisms of the quasi-isotropic laminate, $[0/-60/+60]_s$, strongly depend on the load direction applied to the laminate.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.10a
• /
• pp.656-659
• /
• 1993

The failure phenomenon of Dual Basalt Fibers Reinforced Epoxy Composites(DFC) under tensile load was studied using acoustic emission(AE) technique. AE amplitude and AE energy were mainly associated with the internal microscopic failure mechanism of DFC specimen, such as fiber fracture, matrix cracking, and fiber/matrix debonding. Fiber failures in the DFC specimens were distinguishable by showing the highest AE energy amplitude. They were dependant on the fiber diameters. Matrix cracking was determined from the relatively lower AE amplitude and AE energy, whereas fiber/matrix debonding could not be successfully isolated. AE method, however, can be applicable to the fragmentation method for interfacial strength(IFSS) in DFC specimens with adjusting the threshold to isolate fiber breaks from matrix crack and debonding.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.04b
• /
• pp.155-159
• /
• 1993

최근 많은 생산 시스템의 자동화에 있어서 기계의 상태 진단 및 감시는 설비의 중요도 및 특수성를 고려할때 매우 중요한 비중을 차지하게 되며, 생산 작업을 최적화할 수 있는적당한 제어기술의 필요성과 그에 대한 관심이 날로 증가 하고있는 실정이다. 특히 가공분야에서 많은 부분을 차지하고 있는 절삭가공작업은 기구의 구성이 복잡하고 불확정한 요인을 포함하고있으며 공구의 파손이나 채터진동에 의한 공작물의 정도의 변화가 급속히 발생하기 때문에 이를 위하여 인프로세서 감시가 절실히 요구되고 있다. 그러므로 비정상적인 절삭을 사전에 감지하여 대처함으로써 최적의 작업조 건하에서 안정된 절삭을 할 수 있고 공작기계의 유지, 보수에 경제적인 절감을 기대할 수 있다. 본 연구에서는 2차원 절삭과정중에 발생하는 채터진도에 있어서 절삭 파라메타와 AE 신호와의 관계를 실험적으로 규명하며, AE를 이용한 절삭과정을 모니터링 할 수 있는 방법에 대하여 연구한다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.19 no.2
• /
• pp.129-144
• /
• 1999

플랜트와 같은 장치산업은 내구성 구조물이므로 사용중에 열화가 발생하는 것은 필연적이다. 특히 고온, 고압의 부식환경하에서 사용되는 설비는 손상이 심하므로 가동중에 돌발적인 고장이 발생하여 플랜트의 가동을 중지하거나 파손사고가 일어나 생산손실은 물론 경우에 따라서는 안전사고의 발생, 환경오염 등 사회적인 문제를 일으키므로 이들 설비의 경년열화 실체를 충분히 이해하고 대책을 수립하는 것은 대단히 중요하다. 따라서 본고에서는 장치산업에서 발생하는 열화현상(재료의 연화, 경화 및 취화, 크리프, 피로, 부식, 마모 등)중 손상의 주류를 이루는 연화, 경화 및 취화, 크리프 피로에 대하여 기본적인 손상기구(damage mechanism)와 비파괴적 진단 및 평가 방법에 주안점을 두어, 현재 국내의 각종 플랜트 진단에 실용화된 기술을 해설하여 이 분야에 종사하는 관계자 여러분의 이해에 조금이라도 기여코자 한다.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1995.05a
• /
• pp.961-966
• /
• 1995

국내 상업적으로 운용증인 경수로 원자력 발전소중, 중기발생기의 건전성 유지를 위하여 보수 유지에 많은 비용을 소비하고 있다 특히 중기발생기 전열관으로 사용되는 inconel 600 재질에 많은 문제점이 발생되었다. 전열관 파손에 대한 보수 및 방지기술은 plugging, sleeving, shot penning, Ni-plating 등이 있다. 특히 최근에 개발된 고출력 Nd:YAG 레이저를 이용한 sleeving 보수 기술이 개발되었다. Nd:YAG 레이저를 이용한 보수 방식은 미국의 WH 및 일본의 MHI 등이 선정하여 실용화 단계에 있으며, 이는 광섬유로 전송이 가능한 Nd:YAG 레이저를 이용하여 원격으로 가공할 수 있는 기술이다. 현재 한국 원자력 연구소에서는 전열관 레이저 보수 용접에 대한 개념을 확립하고 장비 및 기구를 개발하였으며, 고리 1 호기 전열관규격에(7/8") 3/4" sleeve tube를 삽입하여 약 50 m 떨어진 곳으로부터 원격 레이저 용접을 실험실적 규모로 실증 하였다.모로 실증 하였다.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1997.05b
• /
• pp.36-41
• /
• 1997

액체금속로는 고온 하중 효과(피로, 크립, 크립-피로)를 고려한 내열응력설계가 중요하다. 최근에는 액금로 후보재료로서 종래의 스테인레스강에 질소를 첨가하여 고온강도를 계량한 316LN 스테인레스강이 개발되었다. 본 연구에서는 액체금속로 재료의 가장 지배적인 손상 기구로 인식되고 있는 피로-크립 파손에 대한 설계자료를 확보하기 위해 DCPD(Direct Current Potential Drop)법에 의한 고온피로균열 측정 시스템을 개발하고 316L 및 스테인레스강인 316LN 스테인레스강에 대한 고온 피로균열진전시험을 수행하였다. 본 연구에 의해 개발된 피로균열진전속도 측정 시스템에 의하면 25$\mu\textrm{m}$ 이하의 분해능으로 균열길이를 측정할 수 있다. 한편 316L 스테인레스강에 질소를 적당량 첨가하면 상온에서 $600^{\circ}C$사이의 온도에서 피로균열진전에 대한저항성이 증가하는 것을 확인하였다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.3
• /
• pp.429-436
• /
• 2013

This study considers how the fatigue behavior and probabilistic properties of SAE1055 steel are related to its hardness level. SAE1055 steel was heat-treated using induction hardening. Five types of specimens were prepared (A: base material, B: through hardened material with HV390, C: through hardened material with HV510, D: through hardened material with HV700, and E: surface hardened material with HV700). Fatigue tests were performed under a stress ratio of R = -1 using a 4-point rotary bending fatigue tester. The fatigue behaviors were greatly influenced by the hardness, but the fatigue limit did not increase over a hardness of HV510. In addition, the effect of the hardness level on the failure mechanism was evaluated using a scanning electron microscope. The probabilistic properties of the fatigue life were investigated using a probabilistic S-N approach, and the effect of the hardness level on these properties was evaluated using a residue analysis.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.20 no.4
• /
• pp.276-284
• /
• 2000

The acoustic emission (AE) behavior of reinforced concrete beams tested under flexural loading was investigated to characterize and identify the source of damage. This research was aimed at identifying the characteristic AE response associated with micro-crack development, localized crack propagation, corrosion, and debonding of the reinforcing steel. Concrete beams were prepared to isolate the damage mechanisms by using plain, notched-plain, reinforced, and corroded-reinforced specimens. The beams were tested using four-point cyclic step-loading. The AE response was analyzed to obtain key parameters such as the time history of AE events, the total number and rate of AE events, and the characteristic features of the waveform. Initial analysis of the AE signal has shown that a clear difference in the AE response is observed depending on the source of the damage. The Felicity ratio exhibited a correlation with the overall damage level, while the number of AE events during unloading can be an effective criterion to estimate the level of corrosion distress in reinforced concrete structures. Consequently, AE measurement characterization appears to provide a promising approach for estimating the level of deterioration in reinforced concrete structure.

• Journal of Yeungnam Medical Science
• /
• v.7 no.1
• /
• pp.81-93
• /
• 1990

The author fractographically analyized the cause of metal failure(the first time this procedure has been used for this metal failure)and also analyized it clinically. In this study, I selected eight cases which have been analyized fractographically. In all these cases, the analysis was done after treatment of metal failure of implants internally fixed to femur shaft fractures at the Department of Orthopedic Surgery, Yeung-Nam University Hospital during the six year period from May 1983 to September 1989. 1. Metal failure occured in five dynamic-compression plates, one Jewett nail, one screw in Rowe plate, and one interlocking nail. 2. The clinical cause of metal failure was deficiency of medial butress in five cases, incorrect position of implant in one case, and incorrect selection of implant in two cases. 3. The time interval between internal fixation and metal failure was four months in one case, between five months to twelve months in six cases, three years in one case. 4. The fractographically analytical cause of metal failure was ; first, impact failure, one case, second, fatigue failure, six cases, machining mark(stress liser), four cases type : low consistent cyclic fatigue failure irregular cyclic fatigue failure third, stress corrosion crack, one case. 5. 316L Stainless Steel has good resistance to corrosion. However, when its peculiar surface film is destroyed by fretting, it shows pitting corrosion. This is, perhaps, the main cause of metal failure. 6. It is possible that mechanical injury occured in implants during the manufacturing of implants or that making a screw hole is the main cause of metal failure.