• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.22 no.2
• /
• pp.123-128
• /
• 2022

The torque of the SRM((Switched Reluctance Motor)) is proportional to the inductance slope, so it has a non-linear torque characteristic, and has a disadvantage in that the torque pulsation is large and noise is severe. In particular, the biggest obstacle to the commercialization of SRM is the pulsating torque generated from the rotating shaft, which has various adverse effects not only on the device itself but also on the peripheral devices. Therefore, various methods for reducing the pulsating torque have been published by domestic and foreign researchers, and there is a study result that the hysteresis controller has an advantage in that it can flow a smooth current compared to the chopping control. However, in determining the hysteresis band, if the band is too small, it has a disadvantage in that it may cause a switching loss due to many switching and an unstable initial start when the encoder is used. Therefore, in this paper, a variable hysteresis controller that can reduce torque ripple in a steady state while having a more stable and fast speed response through the change of the hysteresis band according to the speed error.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.9
• /
• pp.55-63
• /
• 2003

An attitude control system using reaction thrusters for the upper stage of a launch vehicle is considered. The thruster configuration (position and direction) determines control system response, fuel consumption, effective torque and system fault tolerance. We propose a procedure for finding the optimal thruster configuration with desired control effectiveness over the range of selected torque commands. An optimization technique called Particle Swarm Optimization is used for the numerical experiments. The validity of the solution is checked through computer simulations.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.37 no.1
• /
• pp.57-65
• /
• 2001

The speed control without a speed sensor is expected strongly to progress reliability, simplicity and cost performance of Induction Motor(I.M) systems. Also, it contributes to expansion of I.M systems into various industrial application fields. This paper investigates a novel speed sensorless control method of I.M considering the secondary resistance identification based on the transientless torque control technique. Especially, this paper aimed at the identification of the secondary resistance simultaneously with speed estimation superposing of sinusoidal flux wave to a constant flux value. Furthermore, the secondary flux with some frequency is controlled independently on torque control. The proposed speed estimation method is derived from a motor circuit equation theoretically and also it can be conducted easily by detecting primary motor currents and primary voltage commands at every sampling time. Some numerical simulations with the assumption of using a pulse width modulation(PWM) voltage source inverter are performed to verify the proposed method.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.6
• /
• pp.653-658
• /
• 2013

This paper describes a new sensorless speed control method for permanent magnet synchronous motor(PMSM) using direct torque control(DTC). The direct torque control offers fast torque response, lesser hardware and processing costs as compared to vector controlled drives. In this paper the current error compensation technique is applied for sensorless speed control of synchronous motor. Through this method, the controlled stator voltage is applied to the synchronous motor so that the error between stator currents of the mathematical model and the actual motor can be forced to decay to zero as time proceeds and therefore, the motor speed approaches to the setting value. Especially, any PI controllers are not necessary in this control method. The simulation results indicate good speed and load responses from the low speed range to the high.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.13 no.3
• /
• pp.171-178
• /
• 2008

Pressure control of hydraulic pump using SRM with pressure predictor and direct torque control method is presented in this paper. Nowadays, high efficiency and high performance motor drive is much interested in hydraulic pump system. But the hydraulic pump system has an inherent defect that its dynamic behavior causes by interaction between the sensor and hydraulic load. It will make low performance of whole system, even unstable and oscillatory. Proposed system integrates pressure predictor and direct instantaneous torque control (DITC). The pressure predictor includes Smith predictor, which is easy to improve unstable or long oscillation in traditional negative feedback control and popular PID control architectures. And DITC method can reduce inherent torque ripple of SRM, and develop smooth torque to load, which can increase stability and improve the torque response of SR drive. So high dynamic performance and stabilization can achieved proposed hydraulic system. At last, the proposed hydraulic system is verified by simulation and experimental results.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.1
• /
• pp.70-79
• /
• 2005

In this paper, improvement method of control performance by a full-order observer using reduced-order state equation is proposed in the low speed range. Full-order observer using reduced-order state equation is the motor speed and the disturbance torque observer. The proposed algorithm is very stable in the low speed range about 1.9[rpm]. The disturbance torque in the motor drive system degrades speed control performance in the low speed range. The proposed algorithm estimated both motor speed and disturbance torque. The estimated disturbance torque is used as a feedforward value in output of the speed controller, As a result, it improves the response of load torque in the low speed range(1.9rpm).

• Proceedings of the KIEE Conference
• /
• 2005.04a
• /
• pp.210-212
• /
• 2005

최근 급속도로 발전하고 있는 산업분야에서 요구되는 서보 시스템에서 빠른 응답특성, 고도의 정밀성 그리고 안전성에 대한 요구가 커지고 있는 실정이다. 본 논문에서는 이러한 요구에 따라 5상 IPM(Five-phase IPM)의 DTC(Direct torque control)에 대해 고찰하였으며, Texas Instruments사에서 전동기 제어 전용으로 개발된 DSP칩인 TMS320F2812를 이용하여 디지털적으로 제어 알고리즘을 구성하였다. 5상 전동기는 현재 산업현장에서 일반적으로 널리 사용되고 있는 삼상 전동기에 비해 안정성이 높고, 상당 전압의 변화 없이 고정자 전류를 줄일 수 있고, 토크 맥동의 주파수를 높이고 결과적으로 토크의 크기를 감소시킬 수 있다는 여러 가지 장점을 가지고 있으며, 특히 안정성을 요구하는 항공기(Aerospace applications), 전기자동차 및 하이브리드 자동차(Electric or hybrid vehicles)등의 특수한 영역에서 요구가 계속 증가되고 있다. 따라서 본 논문에서는 5상 IPM의 DTC에 대한 특성을 실험을 통하여 확인하였다.

• ICROS
• /
• v.21 no.1
• /
• pp.31-36
• /
• 2015

운전자에게 편의성을 제공하는 차량의 주행관련 Advanced driver assist system (ADAS)에는 차량의 종방향과 횡방향 운동에 대한 제어기가 요구된다. 횡방향 제어를 위해서는 조향 시스템의 조향각 제어가 요구되는데 최근 구조적으로 간단하고 연비향상, 차량의 중량 감소, 빠른 응답성을 가지고 있는 전기적 파워 조향 (Electric power steering, EPS) 시스템이 자동차 산업에서 널리 사용되고 있다. 차량의 주행관련 ADAS를 사용하여 자율 주행 시 EPS 시스템은 상위 제어기에서 계산된 필요한 조향각을 추종 할 수 있도록 조향 핸들의 각 제어를 해야 한다. 그러나 일반적인 EPS 시스템은 운전자가 조향 핸들에 인가된 토크를 보조해 줄 수 있는 토크를 출력해 준다. 본 논문에서는 이러한 문제를 해결하는 방법들을 설명한다. 먼저 EPS 시스템의 기본 기능에 대해서 설명을 하고, 자율 추행 차량을 위한 조항 핸들의 각 제어를 위한 proportional-integral 제어, 슬라이딩 모드 제어 (Sliding mode control), 관측기 기반 비선형 댐핑 제어(Observer based nonlinear damping control) 등과 같은 다양한 기법의 제어 알고리즘들에 대한 방법들이 고찰되었다.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.5
• /
• pp.440-446
• /
• 2006

The magnitude of output torque in a BLDC Motor depends on torque angle so that the exact initial position of rotor is essentially required for good starting. This paper presents a novel starting control method for smooth starting in a position-sensorless controlled BLDC motor drive for reciprocating compressor of refrigerator. The proposed method starts a BLDC motor using information on the initial position of rotor, determined from current response characteristics, and shows robust starting capability to starting load variations. The effectiveness of the proposed method is verified through experimental results.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.7 no.6
• /
• pp.531-536
• /
• 2002

This paper investigates the problem of the speed controller of conventional speed sensorless stator flux-oriented(SFO) induction motor drive, and proposes a robust speed controller to solve the conventional problem. In the proposed method, a robust speed controller for speed sensorless SFO system Is designed by taking advantage of disturbance torque observer and using feedforward.