• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.11
• /
• pp.1183-1189
• /
• 2015

This study focuses on the design of the tapered joints of a wind power turbine. The main variables of the tapered joint are the transmitted torque, shaft diameter, contact area of the tapered ring, and tightening torque of the bolts, which applies a compressive pressure from the hub to the shaft. The stress distribution of the taper fit was calculated under axisymmetric plane strain conditions because of the small taper angle. The axial displacement of the clamp can be calculated from the radial elastic deformation and the taper angle. The stress field of each ring is obtained from the cylinder stress equation. To verify the accuracy of the calculation, finite element (FE) analysis was performed, and the results of the calculation and FE analysis were compared. The hoop stress of the tapered surface showed a discrepancy of approximately 10, but the trends of the stress distributions of each component and the relative movement obtained by FE analysis were in good agreement with the analytical calculation results.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 1999.11a
• /
• pp.264-267
• /
• 1999

복합적층판은 일반적으로 균일한 두께를 갖는 평평한 구조물을 형성하게 된다. 그러나 실제 적용시 적층판의 테이퍼링(tapering)이 요구되는 경우가 존재한다. 테이퍼진 복합재 구조물의 적용분야는 항공기의 날개, 수직/수평 안정판 및 헬리콥터의 로터 블레이드 등이다. (중략)

• Journal of Dental Rehabilitation and Applied Science
• /
• v.37 no.4
• /
• pp.225-231
• /
• 2021

There are many studies on the indications and efficacy of splint therapy commonly used in patients with temporomandibular disorders (TMD). However, there have been no studies on the splint weaning in terms of the splint use tapering period in relation to symptom improvement of TMD. This retrospective study aims to analyze a proper splint weaning method in patients with TMD based on symptom improvement. Materials and Methods: The authors examined 130 TMD patients with TMJ disorders, masticatory muscle disorders, and clenching/bruxism who had received splint therapy (occlusion stabilization splint, anterior positioning splint) of patients who visited the Department of Orofacial Pain and Oral Medicine at Yonsei University Dental Hospital from 2015 to 2020. They were evaluated according to the method to wean splints. Results: The mean splint therapy period was 29.0 months, during which patients wore splints 7 days a week for 8.4 months, 3 - 4 days a week for 9.5 months, and finally 1 - 2 days a week for 11.1 months (a total of 29.0 months, about 2.5 years). Conclusion: It seems that TMD symptoms can be alleviated and side effects such as occlusal change can be minimized if patients wear a splint 7 days a week for the first 6 months, followed by 3 - 4 days a week for the next 6 to 18 months, and finally 1 - 2 days a week after 18 months.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.23 no.5
• /
• pp.145-150
• /
• 2023

Non-uniform optical taper waveguides have been widely used as devices for high-efficiency mode coupling, as they are integrated with single-mode optical fibers or photonic crystal waveguides. In this paper, we present a new platform for chemical sensing and bio-sensing using optical taper waveguides with these characteristics. The principle of operation is based on the coupling efficiency and interference properties of optical directional coupler (DC) and multi-mode interference coupler (MMIC). First, the curvature characteristics of taper sections of DC and MMIC is explained, and the design specifications of optimized taper waveguide to increase waveguide sensitivity is selected. Next, the sensor response to the change in refractive index of sensing analyte is numerically analyzed. Numerical results show that as the length of couplers increases, the effective index per change in refractive index unit (RIU) of analyte increases, and that sensitivity can be tuned using taper DC and MMIC design techniques.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.8
• /
• pp.878-883
• /
• 2003

New feeding structures using linearly and exponentially tapered lines to planar microstrip resonators are proposed. These can overcome the design problems from coupling losses and impedance mismatching by increasing the coupling efficiency. The variation of its feeding angle is evaluated for the insertion loss and bandwidth and the feedline length is optimized at ${\lambda}_g$/2. The ring resonators and patches fed by the tapered line have been designed and implemented. The experimental results show that the insertion loss is enhanced by about 7 dB. Both rings and antennas are better matched, without disturbing the single-mode resonance or distorting their radiation pattern

• Korean Journal of Optics and Photonics
• /
• v.27 no.5
• /
• pp.181-187
• /
• 2016

We report on the parameter-dependent optical characteristics of the unidirectional single-mode lasing square ring cavities. Using the taper-step section in the square cavities, the resonant direction can be selected and we characterize the optical losses by changing the taper lengths. Various kinds of square ring cavities are fabricated, based on InGaAsP/InGaAs multiple quantum well semiconductor materials. From the experimental results we obtain the optimized taper length for a given device structure, while maintaining unidirectional single-mode lasing.

• Korean Journal of Optics and Photonics
• /
• v.31 no.5
• /
• pp.213-217
• /
• 2020

In this study we report a wet-etching-based fabrication method for adiabatic optical-fiber tapers (OFTs), and describe their adiabaticity and HE₁₁ mode evolution at a wavelength of 1550 nm. The profile of the fabricated system satisfies the adiabaticity properties well, and the far-field pattern from the etched OFT shows that the fundamental HE₁₁ mode is maintained without a higher-order mode coupling throughout the tapers. In addition, the measured far-field pattern agrees well with the simulated result. The proposed adiabatic OFTs can be applied to a number of photonic applications, especially fiber-chip packages. Based on the fabricated adiabatic OFT structures, the optical transmission to the inversely tapered silicon waveguide shows large spatial-dimensional tolerances for 1 dB excess loss of ~60 ㎛ (silicon waveguide angle of 1°) and insertion loss of less than 0.4 dB (silicon waveguide angle of 4°), from the numerical simulation. The proposed adiabatic coupler shows the ultrabroadband coupling efficiency over the O- and C-bands.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.7 no.4
• /
• pp.867-871
• /
• 2012

In this paper, we proposed and demonstrated a low loss $1{\times}4$ type plastic optical fiber(POF) coupler incorporating a polymer tapering waveguide region. To avoid leakage loss at the interfaces between the POF and the polymer waveguide, we employed two POF transition regions, in which the cross section of the POF is adiabatically converted from a circular to a rectangular shape without change of its cross-section area. The device was fabricated based on a injection mold made of a silicon rubber. The fabricated POF coupler showed 1.33 dB of excess loss and 2.2 dB of flatness.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.7
• /
• pp.70-77
• /
• 2003

The centerless through-feed grinding is performed by passing the workpiece between the grinding wheel and the regulating wheel. So, the amount of removed material around the leading end, of the workpiece is always more than that around the trailing end until the leading end leaves the grinding wheel. Because of this, there are differences in diameters along the workpiece axis during grinding, and workpiece axis is not parallel to the grinding wheel axis and the contact lines between the workpiece and wheels. Thus the ground workpiece shows tapering error inherently. To eliminate this error, the workpiece axis must be kept to be parallel to the grinding wheel axis. And, the direction of the workpiece axis can be controlled by the work-rest blade. Therefore, the effects of work-rest blade inclination angle on the through-feed centerless ground part are investigated in this study. As a result, it is found that there is a positive inclination angle of the work-rest blade for minimizing the tapering error of a ground workpiece.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2007.11a
• /
• pp.77-78
• /
• 2007