• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2008.04a
• /
• pp.454-457
• /
• 2008

The purpose of this study is to establish 3D equipment database for BIM because of efficient using a BIM tool. In this study (or paper), we analysis the mechanism of using equipment database. And then, a based on this results we apply and conduct the results. Therefore we expect to make better using method of BIM and efficient planning method of equipment.

• Journal of Industrial Technology
• /
• v.20 no.A
• /
• pp.229-238
• /
• 2000

Simulation analysis for an auto body manufacturing system has been performed in this study. The major goal is to figure out the condition yielding the production rate, 70 per hour. It is, however, very difficult to maintain this rate due to inherent system factors such as machine failure rates, machine repair rates, number of carriers between manufacturing lines(shops), carrier speed etc. We first carefully examined the system and developed a simulation model using ARENA. We then applied statistical experimental design concepts for performance analysis. Our results indicate that the buffer size of 30 and quick repair of failed robots are required for the desired production rate. Other factors, on the other hand, are seen to have minor effects on the throughput. The approach taken in this study and the results obtained may provide a practical guideline for performance analysis and thus be applied without trepidation for similar cases.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.28 no.2
• /
• pp.145-156
• /
• 1995

Satellite infrared images were analyzed to study the distribution of eddies off the east coast of Korea from 1987 to 1991. Most of the eddies were filament-type and were generated near the fringe of the East Korea Warm Current (EKWC) flowing northward. Eddies having length of 20-40km and width of 10-20km were most abundant. The meso-scale eddies of 100-200km in diameter were found between Mukho and Wonsan Bay in almost all the images. There was no evidence for the consistent movement of eddies to a definite direction. The Ulleung Warm Eddy, although reported previously by the hydrographic data, could not be identified by the limited amount of infrared imagery.

• Journal of Korean Institute of Industrial Engineers
• /
• v.19 no.3
• /
• pp.91-102
• /
• 1993

This paper suggests an approach to quantitative evaluation of a manufacturing flexibility in automated manufacturing systems. The flexibility of a cell is newly defined and evaluated in use of the environmental change factors which may influence flexibility for satisfying a manufacturing performance objective. The number of machines, the number of operations, machine breakdowns and processing times are considered for this cell flexibility measure. The cell flexibility measures the extent that the cell utilizes the processes to acquire high throughput. Simulation program written in SLAM System was used to help measure cell flexibility. The proposed cell flexibility measure provides a prediction of the influence of the factors on throughput performance, and applies in case of comparison of existing system and a new system, changes in operation conditions of a cell, and comparison of rival machines. Therefore it can be used as decision making criteria for system justification.

• Journal of Applied Reliability
• /
• v.11 no.4
• /
• pp.387-398
• /
• 2011

$217Plus^{TM}$, a newly developed as a surrogate of the MIL-HDBK-217, may be widely applied for reliability predictions of electronic systems. In this study, we performed sensitivity study of the $217Plus^{TM}$ system model to various parameters. Specific attention was put to logistics model and its behavior has been examined in terms of non-component failure causes. We first briefly explained the $217Plus^{TM}$ methodology with system level failure rate evaluation. We then applied experimental designs with several failure causes as factors. We used an orthogonal array with three levels of each parameter. Our results indicate that cannot duplicate, induced, and wear-out causes have dominant effects on the system failures and design, parts, and system management have much less but a little strong effects. The results in this study not only figure out the behavior of the predicted failure rate as functions of failure causes but provide meaningful guidelines for practical applications.

• Journal of Industrial Technology
• /
• v.28 no.B
• /
• pp.227-234
• /
• 2008

Reliability predictions for selected electronic parts using 217-Plus have been performed in this study. 217-Plus has recently developed and may be applied for electronics failure prediction as a surrogate of MIL-HDBK-217. We first briefly reviewed 217-Plus component models. Based on three selected components, predictions using both MIL-HDBK-217 and 217-Plus have been made and the results were compared. Even though the comprehensive conclusion may be drawn from extensive component and system level analyses, the results in this study may provide general insights towards reliability through two specifications.

• Journal of Industrial Technology
• /
• v.28 no.B
• /
• pp.215-226
• /
• 2008

MIL-HDBK-217 has widely been used for electronics reliability predictions. Recently, the $217Plus^{TM}$ has been developed by DoD RIAC and may replace MIL-HDBK-217. A overview of the $217Plus^{TM}$ has been performed in this paper. We first reviewed the overall concepts and reliability prediction procedures. We then explained the component models and the system level model with process grading concepts. Bayesian approach incorporating field data into the predicted failure rate is another feature of this methodology.

• Journal of Industrial Technology
• /
• v.24 no.A
• /
• pp.47-57
• /
• 2004

Industrial efforts for increased market sales have directed towards the development and implementation of on-line marketing systems under recent e-business environment. Internet-based shopping mall is one of the most popular system. A business process model for an intermediary type shopping mall using IDEF0 has been presented in this study. Specific efforts have been focused on defining and analyzing a diversity of business processes embedded in practical B2B and B2C mall system operations. We first briefly examined the considered system with IDEF0 design. We then defined fundamental business processes within shopping mall systems. Upon careful examination and analysis of them, a detailed business process model based on IDEF methodology has been designed. The results in this study may well form a conceptual framework for shopping mall development and operations.

• Journal of Industrial Technology
• /
• v.31 no.B
• /
• pp.51-58
• /
• 2011

Simulation plays a pivotal role in the analysis of complex systems. In this study, a job shop manufacturing system has been analyzed through DBR (Drum-buffer-rope) simulation. Specific attention has been put to examine the rate of due-date achievement. We first derived key factors affecting the system performance. We then developed ARENA simulation program based on DBR of TOC (Theory of Constraints) concepts. Based on the performance measure, factors, and experimental design, we obtained the results. We have drawn meaningful results through examination of the results. The results obtained from this study may provide a good base for practical applications.

• Journal of Korean Society for Quality Management
• /
• v.36 no.4
• /
• pp.29-36
• /
• 2008

최근 자동차 경량화를 위한 부단한 노력이 진행되고 있다. 이 목적에서, HSS (high strength steel)는 전통적인 연강 (mild steel)의 대안으로 널리 사용되고 있다. 본 연구의 목적은 판금의 형단조에 있어서의 공구와 공정설계를 위하여 HSS의 스프링백(springback)을 정확히 예측하기 위한 성공적인 방법론을 추구하고자 함이다. 연구를 위하여 먼저 스프링백의 개념과 그의 측정치들을 설명했으며 U-draw bending 시험을 수행하였다. 시험 결과 및 선정된 파라메터들 중심의 수행평가기준에 근거하여, 주어진 파라메터 조합들을 중심으로 유한요소 해석을 수행하였다. 직교배열을 통하여 스프링백에 대한 인자 효과들을 포괄적으로 분석하였으며 최적 인자 조합들을 도출하였다. 이 과정에서 직교배열상의 한 조합 전체의 데이터가 가용하지 않는 문제가 수반되었으며, 반복적으로 signal-to-noise 비(ratio)를 개선해가는 기법을 적용하여 해결하였다.