In this paper, the forced vibration of damped composite beam with arbitrary section was analyzed. The damping material was assumed to have either complex shear modulus or complex Young???smodulus. Damped composite beam could be modeled using beam elements with less D.O.F. rather than solid elements. Finite element method for these methods was formulated and programmed using complex values. The results of frequency responses revealed good agreement with those of NASTRAN in several beam structures.
To examine the residual stress field resulting from stamping process for the lower control arm of a car, the explicit finite element analysis is performed for the stamping process by way of the ABAQUS Explicit. The residual stress is obtained in terms of the Von Mises stress and other parameters such as equivalent plastic strain, the change of blank thickness, the final configuration of the blank and the spring back effect are also considered. Moreover, discussed is the convergence of the explicit FEM versus the punch sped and the element discretization
Disc specimen with the center crack and edge crack simulated by two-dimensional static method is used to analyze the stress field around the crack tip in terms of the stress intensity factor, K. A simple and convenient method of testing to realize the mifed mode stress intensity factor of the cracked body is used, The conclusions obtatined in this photoelastlc analysis are as follows ; 1. According to this experiment, cracked disc specimen can be used to demonstrate the mixed mode stress intensity factor analysis by simply changing the crack angle from the loading line. 2. Despite the simplicity and continuous data reading, the photoelastic method shows the slightly lower strain reading comparing to the FEM analysis method. 3. In this photoelastic analysis, $K_{I}$ of center cracked disc specimen under a pair of compressive load shows negative value as the crack angle increases over 30$^{\circ}$.
New program for springback analysis has been developed to predict the deformation of springback more accurately. Static implicit FEM is used to find out the static equilibrium after springback. The shell element with 6 dogrees of freedom and 4 nodes is carefully implemented to improve the accuracy and the compatibility between forming analysis and springback analysis. Co-rotational approach and Newton-Raphson nonlinear iteration are used to resolve the nonlinearity of large deformation. The benchmark results show that the developed program gives good predictions in comparison with experimental and other commercial S/W's results. As practical examples, U draw bending and S-rail problems are carried out by the developed program.
In this study, to achieve the optimal conditions for mechanical hyper-fine pattern fabrication process, deformation behavior of the materials during indentation scratch test was studied with numerical method by ABAQUS S/W. Brittle materials (Si, Pyrex glass 7740) were used as specimens, and forming conditions to reduce the elastic recovery and pile-up were proposed. The indenter was modeled as a rigid surface. Minimum mesh sizes of specimens are 1-l0nm. Variables of the nanoindentation scratch test analysis are scratching speed, scratching load, tip radius and tip geometry. The nano-indentation scratch tests were performed by using the Berkovich pyramidal diamond indenter. Comparison between the experimental data and numerical result demonstrated that the FEM approach can be a good model of the nanoindentation scratch test. The result of the investigation will be applied to the fabrication of the hyper-fine pattern.
본 논문은 링형 초음파모터의 진동모드에 의한 진동특성 개선을 제안하였다. 고정자의 압전세락믹과 탄성체에 대한 설계는 공진주파수, 진동모드 및 결합계수 등을 고려한 유한요소법(FEM)에 의해 계산되었다. 6차로부터 8차까지의 진동해석 결과를 통하여, 7차 모드는 결합효율, 최소전력소비 및 굴곡 진동에 있어서 매우 우수한 결과를 얻었다. 또한 7차 모드 이상에서는 입력전압에 대한 출력전류가 매우 크게 증가함을 알 수 있었다. 두께 0.5[mm]∼2[mm]까지의 진동계산 결과 0.5[mm]에서 진동변위가 매우 높은 값을 지님을 알 수 있었다. 이러한 해석결과로부터 본 연구에서는 약 43.86[KHz]의 공진주파수을 갖는 외경 50[mm], 내경 22[mm]의 초음파모터를 제조하였으며 다음의 시뮬레이션 결과 42.2[KHz]와 실험결과43.86(KHz)의 값을 얻었다. 따라서 본 논문의 타당성은 시뮬레이션 결과와 실험결과의 비교 검토를 통하여 거의 일치하는 결과를 입증하였다.
전차선로는 각 경간마다 양단으로 지지점을 갖게 되므로 지지점에서의 탄성도와 경간중앙에서의 탄성도가 같을 수 없다. 이 두 지점의 탄성도의 차이를 나타내는 계수로 불균일율이라는 지수가 정의되어 널리 사용되어왔다. 이 불균일율은 전차선 장력과 경간 길이에 크게 영향 받는다. 그러나 드로퍼의 배치 간격에 따라서도 달라진다. 이 불균일율은 전차선로의 동적인 특성을 예측하는 하나의 변수로 활용되고 결국 집전 성능을 상대 비교하여 판단하는데 활용되며, 직접적으로는 드로퍼 간격을 설계하는데 있어서 중요한 파라미터로 사용되고 있다. 그러나 이 불균일율은 전차선로의 동적 성능을 적절히 반영하는 지수가 되지 못하고 있다고 판단하고 있다. 불균일율의 정의인 경간 중앙에서의 탄성율과 경간 끝 지정의 탄성율과의 단순한 차이 값의 크기만으로는 드로퍼의 수와 배치 간격에 따른 특성을 반영하지 못한다고 판단된다. 이를 여러 가지 다양한 케이스를 가정하여 탄성도 해석 프로그램을 이용하여 평가해본다. 평가 결과를 토대로 드로퍼 수에 따른 보정계수를 갖는 새로운 불균일율 평가 지수를 제시하고자 하며 이 새로운 지수가 기존의 지수보다 보다 집전 성능을 판단하는데 유용한 데이터가 됨을 증명한다. 또한 아울러 불균일율이 다른 가선 구조에 대하여 팬터그래프의 1단과 2단의 스프링 계수의 크기와의 조합과 상환 관계에 따른 집전 성능의 차이를 전차선로-팬터그래프 동역학 시뮬레이션 프로그램을 사용하여 평가한다. 이를 통하여 불균일율에 따른 보다 적절한 팬터그래프 동역학 모델을 제시한다.
본 연구에서는 유연한 접속부를 갖는 유연전자 패키지 플립칩 접속을 위해 폴리머 탄성범프를 제작하였으며, 범프의 온도 및 하중에 따른 폴리머 탄성 범프의 점탄성 및 점소성 거동을 해석 및 실험적으로 분석하고 비교 평가하였다. 폴리머 탄성 범프는 하중에 의한 변형이 용이하여 범프 높이 평탄도 오차의 보정이 용이할 뿐만 아니라 소자가 형성된 칩에 가해지는 응력 집중이 감소하는 것을 확인하였다. 폴리머 탄성 범프의 과도한 변형에 따른 Au Metal Cap Crack 현상을 보완하여 $200{\mu}m$ 직경의 Spiral Cap Type, Spoke Cap type 폴리머 탄성 범프 형성 기술을 개발하였다. 제안된 Spoke Cap, Spiral Cap 폴리머 탄성 범프는 폴리머 범프 전체를 금속 배선이 덮고 있는 Metal Cap 범프에 비해 범프 변형에 의한 응력 발생이 적음을 확인할 수 있으며 이는 폴리머 범프 위의 금속 배선이 부분적으로 패터닝되어 있어 쉽게 변형될 수 있는 구조이므로 응력이 완화되는데 기인하는 것으로 판단된다. Spoke cap type 범프는 패드 접촉부와 전기적 접속을 하는 금속 배선 면적이 Spiral Cap type 범프에 비해 넓어 접촉 저항을 유지하면서 동시에 금속 배선에 응력 집중이 가장 낮은 결과를 확인하였다.
LMFBR(Liquid Metal Fast Breeder Reactor) vessel is operated under the high temperatures of 500-550.deg. C. Thus, transient thermal loads were severe enough to cause inelastic deformation due to creep-fatigue and plasticity. For reduction of such inelastic deformations, Y-piece structure in the form of a thermal sleeve is used in LMFBR vessel under repeated start-up, service and shut-down conditions. Therefore, a systematic method for inelastic analysis is needed for design of the Y-piece structure subjected to such loading conditions. In the present investigation, finite element analysis of heat transfer and inelastic thermal stress were carried out for the Y-piece structure in LMFBR vessel under service conditions. For such analysis, ABAQUS program was employed based on the elasto-plastic and Chaboche viscoplastic constitutive equations. Based on numerical data obtained from the analysis, creep-fatigue damage estimation according to ASME Code Case N-47 was made and compared to each other. Finally, it was found out that the numerical predictio of damage level due to creep based on Chaboche unified viscoplastic constitutive equation was relatively better compared to elasto-plastic constitutive formulation.
고층건축물의 수평변위 제어에 필요한 브레이스는 구조물의 경제성 확보를 위해 주로 새장한 부재를 설치하여 인장하중에 저항하도록 하는 경우가 많다. 하지만, 브레이스에 압축하증이 작용할 경우에는 부재가 하중에 저항하지 않는 부재로 상정하여 설계되고 있다. 이는 브레이스에 압축하중이 작용할 경우 부재의 탄성좌굴이 발생하게 되어 급격히 내하력을 잃어버리게 되기 때문이다. 이러한 문제를 해결하기 위해 많은 연구가 이루어져 왔으며, 그중 대표적인 것이 응력제한장치라 할 수 있다. 응력제한장치는 세장한 부재가 압축하중에 의해 탄성좌굴이 발생하기 전에 부재가 항복하여 안정적인 거동을 유도하는 것을 목적으로 하고 있다. 본 논문에서는 응력제한장치로서 절판방식을 제안하고 실험과 유한요소 해석을 수행하였다. 실험은 절판단면의 경사각을 변수로 하여, FLD장치 및 FLD를 장착한 부재에 대한 압축실험 및 해석을 진행하였다. 그 결과 절판방식의 실험체는 항복 후 소성영역에서 내력의 큰 저하 없이 안정적인 거동을 나타내고 있어 응력제한방식으로서 유효함이 확인되었다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.