• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1995.04a
• /
• pp.116-120
• /
• 1995

본 연구의 목적은 탄성 스프링 지지된 외팔보 모델의 고유진동수를 엄밀해, 유한요소법의 근사해, 실험 값을 비교하여 해의 타당성을 검토하고, 진동 특성을 분석함으로서 이러한 보 모델에 대한 유용한 설계 기초자료를 얻는데 있다.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.7 no.5
• /
• pp.27-35
• /
• 2007

This study presents a non -prismatic beam element for modeling the elastic and inelastic behavior of the steel beam, which has the post-Northridge connections in steel moment frames that are subjected to earthquake ground motions. The elastic stiffness matrix for non-prismatic members with reduced beam section (RES) connection is in the closed-form. The plasticity model is of a discrete type and is composed of a series of nonlinear hinges connected by rigid links. The hardening rules can model the inelastic behavior for monotonic and random cyclic loading, and the effects of local buckling. Verification and calibration of the model are presented in a companion paper.

• Computational Structural Engineering
• /
• v.11 no.4
• /
• pp.383-390
• /
• 1998

0.93m/sec의 평균속도는 변위제어 삼점휨 실험된 콘크리트 보의 하중-변위 측정결과를 선형탄성파괴역학모델과 가상균열모델에 기초한 유한요소법으로 분석하였다. 두 모델 모두 실험결과와 잘 일치하며, 균열성장길이가 약 60∼70㎜가 될 때까지 안전된 균열성장을 보이다 불안정한 균열성장에 의해 파손되었다. 선형탄성파괴역학모델에 의한 수치해석 결과 에너지해방률은 균열성장길이에 비례해서 증가하였으며, 최대값(202N/m)에 이르게 되면 일정한 값을 유지하였다. 가상균열모델에 기초한 수치해석결과 이 연구에 사용된 하중속도와 시험편의 크기에 대해 70㎜의 완전한 파괴진행대가 평성되었으며, 이는 기존의 정적 실험결과에 대한 수치해석 결과보다 상당히 작은 값이었다.

• Composites Research
• /
• v.14 no.3
• /
• pp.1-9
• /
• 2001

A new non-destructive fatigue prediction model of the composite laminates is developed. The natural frequencies of fatigue-damaged laminates under extensional loading are related to the fatigue life of the laminates by establishing the equivalent flexural stiffness reduction as a function of the elastic properties of sublaminates. The flexural stiffness is derived by relating the 90-ply elastic modulus reduction, and using the laminate plate theory to the degraded elastic modulus and the intact elastic modulus of other laminates. The natural frequency reduction model, in which the dominant fatigue mode can be identified from the sensitivity scale factors of sublaminate elastic properties, provides natural frequency vs. fatigue cycle curves for the composite laminates. Vibration tests were also conducted on $[{90}_2/0_2]_s$ carbon/epoxy laminates to verify the natural frequency reduction model. Correlations between the predictions of the model and experimental results are good.

• Computational Structural Engineering
• /
• v.2 no.4
• /
• pp.79-88
• /
• 1989

The behavior of composite beams in steel building structures subjected to lateral loading is studied. Mathematical models for the stiffness of composite beams and the strength at the connections, which are dependent on details of the connections are developed based on the previous experimental results and the results from numerical analyses. Analytical models for the skeleton and hysteresis curves of cantilever composite beams are also presented. A single component model for the composite beam, consisting of elastic beam and the end springs at which all the inelstic deformations within a member are lumped, is implemented into the computer program, DRAIN-2D. And a comparison of analytical results is made with the experimental results.

• Journal of the Korea Concrete Institute
• /
• v.20 no.3
• /
• pp.345-356
• /
• 2008

In the previous study, direct inelastic strut-and-tie model (DISTM) was developed to perform inelastic design of reinforced concrete members by using linear analysis for their secant stiffness. In the present study, for convenience in design practice, the DISTM was further simplified so that inelastic design of reinforced concrete members can be performed by a run of linear analysis, without using iterative calculations. In the simplified direct inelastic strut-and-tie model (S-DISTM), a reinforced concrete member is idealized with compression strut of concrete and tension tie of reinforcing bars. For the strut and tie elements, elastic stiffness or secant stiffness is used according to the design strategy intended by engineer. To define the failure criteria of the strut and tie elements, concrete crushing and reinforcing bar fracture were considered. The proposed method was applied to inelastic design of various reinforced concrete members including deep beam, coupling beam, and shear wall. The design results were compared with the properties and the deformation capacities of the test specimens.

• Journal of Biomedical Engineering Research
• /
• v.21 no.6
• /
• pp.575-581
• /
• 2000

본 논문에서는 척추침생검 시뮬레이터에서 사용의 햅틱 디바이스인 PHANToM(sup)TM을 이용하여 사실적인 힘을 구현하는 방법을 보여준다. PHANToM(sup)TM은 툴의 끝부분에서 좌표축 방향으로만 힘을 낼 수 있는 단점이 있으며, 시스템의 구동장치의한계로 인하여 딱딱한 물체에 닿을 때 불안정한 특성을 보인다. 또한 좁은 영역 안에서 복잡한 조직들로 인한 급격한 강도 변화도 시스템의 불안정을 초래한다. 모사되는 힘은 두가지 성분으로 나뉜다. 하나는 바늘이 삽입될 때 바늘의 길이 방향으로 느껴지는 힘으로 생체 조직의 모델을 통해 값이 구해진다. 다른 하나는 바늘이 피부를 뚫고 지나간 이후에 바늘이 초기 삽입 방양을 유지 시켜주는 회전방향 힘으로 피봇을 이용하여 구현하였다. 불안정성 문제와 바늘이 튀어나오는 문제는 램핑 필터와 시간변수를 이용하여 제거하였다. 침생검 과정은 생체조직의 탄성 변형뿐 아니라 파괴가 일어나는 변형이므로 사실적인 힘을 구현하기 위해서 실험 데이터를 이용하여 삽입 깊이에 따라 탄성 계수와 마찰 상수가 변하는 모델을 제안하였다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.1A
• /
• pp.19-24
• /
• 2011

Concrete columns strengthening effect due to FRP (Fiber Reinforced Polymer) confinement depends on the elastic modulus of the FRP. This study analyzes the retrofitting effect of FRP confinements according to elastic modulus of FRPs using the existing data and suggests a practical model to assess the strengthening effect. This study subdivides the FRP elastic modulus into three parts based on normal concrete and steel elastic modulus. The slope and the y-axis intersection seem to increase with increasing FRP elastic modulus. In addition, the strengthening effect does not develop up to some amount of FRP confinement having relatively smaller elastic modulus than the compressive elastic modulus of concrete. In this case, a linear model to assess the strengthening effect is hard to be used. Thus, this study suggests that the FRP jackets having 2 times larger elastic modulus than that of concrete are recommended to be used for retrofit of concrete and that a linear model can be applied for the case. The suggested model shows nearly the same result regardless to the restraint of the y-axis intersection. This has been observed at the model of steel confinement and, thus, is a reliable result.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.2A
• /
• pp.233-242
• /
• 2008

This study presents a non-prismatic beam element for modeling the elastic and inelastic behavior of steel beams, which have the post-Northridge(cover plate) connections in steel moment frames that are subjected to earthquake ground motions. The elastic stiffness matrix for non-prismatric members with increased beam section (IBS) connection is in the closed-form. The plasticity model is of a discrete type and is composed of a series of nonlinear hinges connected by rigid links. The hardening rules can model the inelastic behavior for monotonic and random cyclic loading, and the effects of local buckling. Moreover the determination of yield surfaces, stiffness parameters, and hardening (or softening) rule parameters for IBS beam element were described. Analytical results of the IBS beam element show good correlation with test data and FEM results.

• Geotechnical Engineering
• /
• v.8 no.4
• /
• pp.67-80
• /
• 1992

In the analysis of dynamic problem, determination of mazimun shear modulus is essential for the estimation of shear stress at any strain level. Although many models for silica sands were presented, the direct accomodation of those models to crushable sand would be difficult because of crushability during torsion. In this research dynamic behaviour of tested sand is presented. The shear modulus of loose crushable sand shows similar results to silica sand. However, as the density of crushable sand increases the shear modulus decreases because of crushability by increasing surface contact area. And modulus number is expressed in terms of state parameter by Been and Jefferies (1965).