• Journal of the Korea Institute of Building Construction
• /
• v.17 no.6
• /
• pp.577-585
• /
• 2017

HPC method is developing to improve the constructability and structural performance of the existing PC method. The objective of this study is to develop construction procedures and to analysis of construction period for HPC method. In order to develop construction procedures, the building construction data of the existing half-slab method was analyzed. Analyzing design drawings and specifications of nine construction cases, a prototype of half-slab method, was drawn. Applying the core technology of HPC method to the drawn prototype of half-slab method, a prototype of HPC method, was developed. The differences of both methods were 'installing PC column' and 'placing topping concrete'. To analysis the differences of both methods, seven construction cases were analyzed. According to the analysis for HPC method, cases1 and 2 had columns divided for construction shortened about 16% of a construction period. The schedule of column assembly work was analyzed to be shortened much. That is judged to be because the use of a hollow PC column leads to a decrease in the number of columns. In particular, if HPC method is applied to a building construction site using large columns, it is analyzed to shorten a construction period more than the existing Half-slab method.

• Journal of radiological science and technology
• /
• v.39 no.3
• /
• pp.435-441
• /
• 2016

The importance of radiation dose display of medical X-ray equipment was emphasized, while third edition of IEC(International Electrotechnical Commission) 60601 started to apply. The existing medical X-ray equipment selected a method for attaching the DAP(Dose Area Product) meter when the dose display. However, because the DAP meter was dependent on all of the income, And it did not yet produced in Korea. So, we received the support of Seoul R&BD Program(Grants No. C1152055) to produce DAP meter prototype of the Domestically technology. In this study, the performance of this prototype was evaluated by comparing the German company's product Evaluation item was an electronic capture performance, radiation dose dependence, radiation quality dependence, energy transmittance, repeatability, light transmittance of 6 entries. And IEC 60580 was based on this evaluation. Evaluation results were electronic capture performance intrinsic error 9.5%, radiation dose dependence limits of variation 1%, repeatability coefficient of variation 2%, energy transmittance 91% each assessment was passed. However radiation quality dependence limits of variation 29%, light transmittance 55% was less than acceptance criteria.

• Journal of the Korean Wood Science and Technology
• /
• v.37 no.4
• /
• pp.357-363
• /
• 2009

This study was carried out to investigate whether adhesive used in manufacturing glulam can be used to bond wood and GFRP, when considering working process and economical efficiency. The six different glulams were manufactured, changing the adhesives and the mixing ratios of the adhesives, and investigated by the block shear test and the delamination of the water soaking or boiling water soaking. The three glulams were manufactured, using the resocinol resin based adhesive, the PVAc resin based adhesive and the epoxy resin adhesive, and the other three glulams, using the adhesives mixing resocinol resin and PVAc resin. The block shear strength is higher than $7.1N/mm^2$ in all types, which is standard of KS F3021. However, in the wood failure the block shear strength was the highest as 65.9% in the PVAc. The delamination of glulams glued with PVAc adhesive, which was 1.08% in water soaking and 4.16% in boiling water soaking, was lower than 5.00% which is the standard of KS F 3021, and the adhesive strength is good. In glulams glued with only resocinol resin adhesive, the wood layers were good as 1.26% in the water soaking delamination and 0.00% in the boiling water soaking delamination. The GFRP layers were not good as 21.85% in the water soaking delamination but were good as 1.45% in the boiling water soaking delamination.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.12
• /
• pp.1380-1393
• /
• 2010

This paper presents a design, fabrication and the test results of planar active electronically scanned array(AESA) radar prototype for airborne fighter applications using transmit/receive(T/R) module hybrid technology. LIG Nex1 developed a AESA radar prototype to obtain key technologies for airborne fighter's radar. The AESA radar prototype consists of a radiating array, T/R modules, a RF manifold, distributed power supplies, beam controllers, compact receivers with ADC(Analog-to-Digital Converter), a liquid-cooling unit, and an appropriate structure. The AESA antenna has a 590 mm-diameter, active-element area capable of containing 536 T/R modules. Each module is located to provide a triangle grid with $14.7\;mm{\times}19.5\;mm$ spacing among T/R modules. The array dissipates 1,554 watts, with a DC input of 2,310 watts when operated at the maximum transmit duty factor. The AESA radar prototype was tested on near-field chamber and the results become equal in expected beam pattern, providing the accurate and flexible control of antenna beam steering and beam shaping.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.21 no.2
• /
• pp.227-242
• /
• 2019

This paper presents a method to predict ground types ahead of a tunnel face utilizing operational data of the earth pressure-balanced (EPB) shield tunnel boring machine (TBM) when running through soil ground. The time series analysis model which was applicable to predict the mixed ground composed of soils and rocks was modified to be applicable to soil tunnels. Using the modified model, the feasibility on the choice of the soil conditioning materials dependent upon soil types was studied. To do this, a self-organizing map (SOM) clustering was performed. Firstly, it was confirmed that the ground types should be classified based on the percentage of 35% passing through the #200 sieve. Then, the possibility of predicting the ground types by employing the modified model, in which the TBM operational data were analyzed, was studied. The efficacy of the modified model is demonstrated by its 98% accuracy in predicting ground types ten rings ahead of the tunnel face. Especially, the average prediction accuracy was approximately 93% in areas where ground type variations occur.

• Journal of Food Hygiene and Safety
• /
• v.24 no.4
• /
• pp.318-323
• /
• 2009

Dahi is yoghurt like fermented dairy products available in Bangladesh made by traditional ways from raw milk. The aim of the present study was to check and compare the present quality status of the market dahi in reference to laboratory made dahi. For this, dahi was prepared in the laboratory (A) and collected from Kishoregonj district (B), Gazipur district (C), Bogra district (D) and Dhaka district (E and F). Consumer acceptance quality was judged on 100 point by a judge panel and chemical and microbiological quality test were done by established methods. 'A' type dahi was superior followed by E, D, F, B and C considering the consumer acceptance quality parameter. From chemical test, it appears that, B possess the lowest pH ($3.75\;{\pm}\;0.05$) and highest was in C ($4.46\;{\pm}\;0.15$). Total solids content of F type dahi ($318.40\;{\pm}\;4.44\;g/kg$) was highest and fat ($52.00\;{\pm}\;2.00\;g/kg$), protein ($44.33\;{\pm}\;2.00\;g/kg$) and ash ($10.76\;{\pm}\;0.31\;g/kg$) content were also higher in F type dahi. E and A type dahi were also with considerable figure in chemical quality parameter. Dahi B was inferior in respect of microbiological quality- total viable count (TVC) (${\times}\;10^5\;cfu/ml$) content was $94.00\;{\pm}\;4.58$, yeast (cfu/ml) content was $183.33\;{\pm}\;15.28$ and mold (cfu/ml) content was $53.33\;{\pm}\;15.28$. The TVC (${\times}\;10^5\;cfu/ml$), yeast (cfu/ml) and mold (cfu/ml) content of A type dahi were $39.67\;{\pm}\;4.51$, $50.00\;{\pm}\;10.00$ and $20.00\;{\pm}\;10.00$, respectively. Considering all the three major quality aspects dahi A was superior than others followed by F, D, E, C and B.

• Journal of the Korean Wood Science and Technology
• /
• v.38 no.1
• /
• pp.1-10
• /
• 2010

In this study, to study an effective use and improve strength performances of woods and wood-based materials, three-ply hybrid laminated woods which are composed of spruce in the face and three kinds of wood-based boards (MDF, PB, OSB) in the core were manufactured, and the effect of constitution elements used for the core laminae on bending creep performances was investigated. The shape of creep curves showed exponential function plots which the upper right side was increased, and differed among the kinds of wood-based boards used for the core laminae of hybrid laminated wood. The creep deformation perpendicular to the grain of faces of hybrid laminated woods was in order $C_{\perp}$(P) > $C_{\perp}$(M) > $C_{\perp}$(O) with PB, MDF and OSB in the core, respectively. It was found that the creep deformation arranged with OSB in the core had 2 times smaller than those arranged with MDF and PB in the core. By hybrid laminating, the creep deformation of spruce perpendicular to the grain was markedly decreased. On the other hand, the creep deformation parallel to the grain of the faces ($C_{\parallel}$ type) of hybrid laminated woods was in order $C_{\parallel}$(P) > $C_{\parallel}$(O) > $C_{\parallel}$(M) with PB, OSB and MDF in the core. The ratios among three hybrid laminated woods were considerably decreased, especially the difference between $C_{\parallel}$(P) and $C_{\parallel}$(O) hybrid laminated woods arranged with PB and OSB in the core was very small. These values showed 0.108~0.464 times smaller than creep deformation of three wood-based boards and it was found that creep deformation of three wood-based boards was considerably decreased by hybrid laminating. Creep anisotropy of hybrid laminated woods was greater in creep deformation than in initial deformation, whereas it was found that the values was much smaller than that of spruce parallel laminated woods.

• Journal of ILASS-Korea
• /
• v.20 no.2
• /
• pp.70-75
• /
• 2015

Swirl flow in the gun type burner has an impact on the stabilization of the flame, improvement of the combustion efficiency. The swirl flow is created by the spinner which is inside the airtube that guide the combustion air. Gun type burner has generally the inner devices composed electronic spark plug, injection nozzle, combustion device adaptor, and spinner. These inner components change the air flow behavior passing through airtube. So, this study conducted the measurement using by hot-wire anemometer and analyzed effect of the swirl number of spinner on the exhaust air of gun type burner. Turbulence characteristics come up in this study was mean velocity, turbulence intensity, kinetic energy, shear stress and flattness factor of the air flow with the change of the distance of axial direction and tangential direction from the exit of the airtube.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2003.11b
• /
• pp.793-796
• /
• 2003

B2B 전자상거래와 같이 XML을 이용한 정보교환이 확산되고 있으며 이에따라 상호 교환되는 정보에 대하여 체계적이고 안정적인 저장 관리가 요구되고 있다. 이를 위해 XML 응용과 데이터베이스 연계를 위하여 다양한 연구가 XML DTD와 관계형 데이터베이스 중심으로 수행되었다. 그러나 XML DTD가 다양한 데이터 타입 및 표현의 한계 때문에 관계형 데이터베이스와 원활한 연계가 불가능하게 되었다. 그러므로 다양한 데이터 타입과 데이터 표현에 강력한 XML Schema에 대한 연구가 필요하게 되었다. 또한 계층구조를 2차원 정보로 변환하는 방법에 의해서 각 구조화된 정보를 관계형 데이터베이스로 저장하기 위한 데이터 모델링과 XML schema 모델링이 요구된다. 본 논문에서는 XML schema로 정의된 XPDL 정의 스키마를 UML로 변환하는 방법론과 UML을 RDB 스키마로 변환하는 방법론을 제시함으로써, 워크플로우 정의 언어인 XPDL 정의 스키마를 토대로 관계형 데이터베이스의 스키마를 확정하는 방법론을 제안하였다.

• Science of Emotion and Sensibility
• /
• v.1 no.2
• /
• pp.81-91
• /
• 1998

운전자의 안전과 감성적 요구사항이 중요시 되는 차세대 자동차의 IP(Instrument Panel) 설계를 위해 운전자으 인지특성을 고려하였다. 오디어 유닛과 HVAC(Heat, Ventilation and Air Condition)등의 주요 IP 구성요소 설계에 중점을 두었으며, 운전자의 인지특성과 가장부합하는 형태의 IP를 도출하기 위해 인지실험을 실시하였다. 첫 번째로, 기존의 차량에 설계된 IP 궁성요소를 분석하였으며, 이를 바탕으로 버튼의 수와 배열, LCD패널의 위치등을 조합하여 총 16개의 IP 프로토타입을 제작하였다. 다음으로, 제작된 프로타입을 각각 0.2, 0.4, 0.6초의 간격으로 Tachisto scope를 이용하여 피실험자에게 제시한후, 인간의 인지 지도(Human cognitive Map)에 근거한 '그리가 방법(Drawing Method)'을 이용하여 그들의 단기기억(Short-term Memory)상의 정보를 주어진 답안지에 그리도록 하였다. 이 인지실험의 다구찌 분석을 통하여 운전자의 인지특성을 고려한 최적의 IP형태를 제시하였다.