• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.4
• /
• pp.671-678
• /
• 2020

In this paper, a wireless measurement system has been developed which can measure the deformation of a tire in real time by utilizing strain gauge sensors and Zigbee wireless communication. A strain gauge sensor is mounted inside the tire and then the strain on the tire is obtained using the DSP module. The acquired sensor values are transmitted into the vehicle by radio communication. The wireless receiver module installed inside the vehicle can monitor the deformation of the tire in real time. The deformation of the tire can be used for measuring the load applied to each tire or the speed of the tire. The load or speed applied to the tires are essential parameters for the stable control of autonomous vehicles.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.1237-1238
• /
• 2015

이 논문은 타이어 변형량을 측정하는 변형량 센서의 시제품을 modeling하여 COMSOL Multiphysics FEM 해석 프로그램을 통해 시뮬레이션을 수행한 것을 다룬 것이다. 센서의 구조 중에 센서의 성능에 큰 영향력을 미치는 구조를 변수로 잡아 각 변수에 따른 센서의 capacitance의 linearity와 sensitivity을 시뮬레이션을 통해 도출했다. 도출한 값을 토대로 센서 구조에 대한 최적의 범위를 구하고 센서의 시제품의 구조 변수의 값이 이 범위 내에 있는 것을 보여 시제품의 성능에 대한 검증했다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.3
• /
• pp.142-147
• /
• 2013

Over the past few years, intelligent tire is developed very actively for more accurate measurement of real-time tire forces generated during vehicle driving situation. Information on the force of intelligent tire could be used very usefully to chassis control systems of a vehicle. Intelligent tire is based on deformation of tire's inner surface from the waveform of a SAW, or Surface Acoustic Wave. The tire vertical force is estimated by using variance analysis of sensor signals. The estimated tire vertical force is compared with the tire vertical force generated during vehicle driving situation in real-time environment. The scope of this paper is a correlation study between the measured sensor signals and the tire vertical force generated during vehicle driving situation.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.6C
• /
• pp.259-265
• /
• 2012

This paper investigates engineering characteristics of lightweight soils mixed with air foam and tire powder. Lightweight soils could be used as foundation materials, back-fills of reducing vibrating or abutment, and so on. Unconfined and triaxial compression tests were carried out to analyze strength and deformation characteristics of lightweight soils by changing target moist unit weight and cement contents. In comparison with strength characteristics of two different kinds of lightweight soils with same most unit weights ($13kN/m^3$), unconfined compression tests showed similar compressive strength, however, triaxial compression tests showed that compressive strength of lightweight soils mixed with waste tire powder was relatively larger strength than that of lightweight soils mixed with air foam because of elasticity of waste tire powder. Also, unconfined and triaxial compressive strengths of most of lightweight soils increase with increases of moist unit weight and cement contents. However, the strength of lightweight soils mixed with air foam under $11kN/m^3$, when moist unit weight exceeds a certain cement contents, decreases even though cement contents increase because of the effect in a void gap of air foam.

• Journal of Korean Society of Transportation
• /
• v.28 no.3
• /
• pp.119-130
• /
• 2010

Reconstruction analysis of traffic accident is done by analyzing diverse data such as the road, accident traces and damage on the automobile. Most data can be a variable in the process of analysis, and measurement error of the data occurs from the investigator, tool and the given environment. Therefore, accident analysis always has some risks of measurement uncertainty. This research quantify the uncertainty in traffic accident analysis by conducting repetitive measurement experiments for variables with high probability of uncertainly such as length (i.e. geometric structure of the road, tire marks) and coefficient of friction. This paper also suggests an analysis result for the uncertainly of photographic observation of automobile crush measurement. These statistical distributions can help determine appropriate ranges for the input data in order to estimate the accident reconstruction uncertainty.

• Composites Research
• /
• v.26 no.4
• /
• pp.223-229
• /
• 2013

Hybrid composite strut tower was designed to prevent permanent deformation of upper mount by the impact from the uneven road. When exceeding energy absorption capacity of tire and suspension systems, residual impact is delivered to upper mount. Especially, in case of using high-rigidity suspension system for high driving performance, the conventional strut tower can be easily deformed due to reduction of energy absorption capacity of suspension systems. In this study, optimal design of hybrid composite strut tower which made of back-up metal and carbon fiber reinforced composite was suggested by using finite element analysis, and low velocity impact test was performed to investigate their dynamic characteristics. Also, 3D measuring and ultra c-scanning methods were carried out to diagnose damages in the strut towers.

• 한국방재학회:학술대회논문집
• /
• 2011.02a
• /
• pp.197-197
• /
• 2011

최근 들어 전력 사용량의 증가로 인한 화력발전소의 부산물인 석탄회 중 바텀애시와 각종 공공사업과 관련하여 해마다 현장발생토의 발생량이 지속적으로 증가하고 있는 추세이다. 바텀애시와 현장발생토사를 효과적으로 재활용하는 방법 중 유동성 뒤채움재를 개발하여 활용하는 방안을 모색하기 위한 연구이다. SP로 분류된 흙 현장발생토와 서천 화력발전소에서 발생하는 석탄회 중 입경이 0.9~1.5mm의 바텀애시만을 선별하여 현장발생토와 바텀애시의 비율을 7 : 3으로 변환한 최적배합을 선정하여 강재로 제작된 가로 80cm, 세로 60cm, 높이 90cm의 모형토조를 이용하여 실험을 진행하였으며, 사용상 지하 매설이 되는 관의 거동 특성은 확인하기 위하여 내경 30cm, 두께 8mm의 연선관 중 하나인 PVC관을 원형지하매설관으로 선정하여 배합을 타설하는 과정과 타설 후 7일간의 양생기간을 거친 후 차량하중으로 가정할 수 있는 하중을 가하여 원형지하매설관의 관외부에서 수직방향과 수평방향의 토압과 관내부의 수직 수평방향 변위 그리고 관 자체의 횡 종단 변형을 측정하여 원형지하매설관의 거동특성을 파악하였다. 타설시 지하매설관은 유동성 뒤채움재의 특성으로 인하여 시간이 지남에 따라 안정화되는 것을 확인할 수 있었으며, 최대하중을 3300kgf로 하여 하중 재하 후 지하매설관의 거동특성은 대체적으로 일반 모래를 사용하여 실험한 값보다 적은 변형 특성을 보이고 있으나 수평토압의 경우 일반적인 흙의 변형과 전혀 상이한 결과값을 보이는 경우도 있어 추가적인 실험 및 고찰의 필요하다. 본 실험에서 사용한 최적배합비 이외의 배합으로 같은 실험을 수행하여 바텀애시 량의 가감 및 재활용 재료인 폐타이어 고무칩등을 첨가한 실험을 계획하고 있으며 추후 실내시험과 모형실험을 토대로 유한요소해석을 추가로 시행하여 실험값과 해석값의 비교를 할 예정이다.

• Elastomers and Composites
• /
• v.52 no.2
• /
• pp.114-130
• /
• 2017

Enhancing the properties of rubber, such as the tensile strength, modulus, and wear abrasion, by the addition of carbon black and silica as fillers is very important for improving the performance of rubber products. In this review, we summarize the general features of 'the reinforcement of rubber by fillers' and the equations for representing the reinforcement phenomena. The rubber reinforcement was attributed to enhancement of the following: the rubber, bound rubber, formation of networks, and combination between rubber chains and silica followed by entanglement. The reinforcement capability of silica species with different surface and networked states demonstrated the importance of the connection between the silica particles and the rubber chains in achieving high reinforcement. The model involving combination followed by entanglement can provide a plausible explanation of the reinforcement of rubber by carbon black and silica because the combination facilitates the concentration of rubber chains near the filler particles, and entanglement of the rubber chains around the filler particles enforces the resistance against deformation and breakage of rubber compounds, resulting in high reinforcement.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.11 no.3
• /
• pp.97-103
• /
• 2011

In this research, a small-scaled laboratory test and FEM analysis have been carried out to evaluate the feasibility of field construction with couple of recycled materials, such as in-situ soil, water-treatment sludge, and crumb rubbers. A static loading, which simulates the real traffic load, was adopted in lab test. The test was carried out, according to simulated field construction stages, such as excavation, bedding materials and pipe installation, placing and curing of controlled low strength materials, and simulated traffic loading. Couple of measuring instruments were adopted. The maximum vertical and horizontal deformations were 0.83% and 1.09%, during placing the CLSM. The measured vertical and horizontal deformations with curing time were 0.603mm and 0.676mm, respectively. The reduction effect of vertical and lateral earth pressure was relatively big. Also, FEM analysis was carried out to get the deformation, earth pressure and strain of PVC with different Controlled Low Strength Materials(CLSM) materials.

• Composites Research
• /
• v.16 no.3
• /
• pp.9-17
• /
• 2003

In order to simulate the crack connection between cords and the interply crack growth in the belt-layer of real tire, 2 ply rubber/cord laminate specimens with exposed edges were tested in 4~11mm displacement control. Measurement of the crack connection is evaluated when crack reaches the half of the length between 45$^{\circ}$ aligned cords, and the amount of the crack growth is measured by the steel probe method. 2 dimensional analytic modeling was performed to simulate the crack connection between cords at the exposed edges. Also, the theoretical life of the specimens was calculated from the crack connection life between cords(critical value) and from the critical value to the final failure by the use of Tearing energy(T); the strain energy release per unit area of one fracture surface of a crack. Then, theoretical life was compared with those of experiments. The life prediction up to the critical value has about 20% error compared to experimental life, and up to the final failure about 65% error. Therefore, total theoretical life has about 45% error compared to the experimental life, which is conceivable in the case of rubber.