• Applied Biological Chemistry
• /
• v.51 no.2
• /
• pp.108-113
• /
• 2008

Azoxystrobin applied by aqueous WP suspension 50 mg/l was slightly absorbed into cucumber leaf in the absence of activator surfactant 24 h after spraying, but was increased to 25.7% by adding polyoxyethylene monohexadecyl ether (12 moles of ethylene oxide, CE-12) 500 mg/l. Only 4.1% of kresoxim-methyl WDG 100 mg/l in the absence of surfactant was absorbed into cucumber leaf 24 h after spraying, but was increased to 58.0% by adding polyoxyethylene monooctadecyl ether (14 moles of ethylene oxide, SE-14) 1,000 mg/l. The effect of CE-12 500 mg/l on foliar uptake of kresoxim-methyl at 50 mg/l was twice bigger than on azoxystrobin. Fungicidal activity of azoxystrobin WP against cucumber powdery mildew was marginally increased by adding surfactants to facilitate foliar uptake of azoxystrobin, so that the further increase of azoxystrobin uptake into cucumber plant by the addition of adjuvant was not a practical mean for enhancing the formulation efficacy in view of fungicidal activity. It was not possible for kresoxim-methyl to assess the adjuvant effect on the fungicidal activity in a greenhouse trial due to the vapor effect of active ingredient.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.9
• /
• pp.911-917
• /
• 2015

The objective of this work focuses on the analysis of injection rate and macroscopic spray behavior characteristics with injection pressures as well as combustion and exhaust emission characteristics with injection timing and injection pressure by using a common rail single-cylinder diesel engine. The injection rate was measured by applying the Bosch method, and macroscopic spray behavior characteristics were analyzed with a constant-volume vessel and a high-speed camera. In addition, combustion and emission characteristics were analyzed in a common-rail single-cylinder diesel engine with precise control of fuel injection timing and pressure. For injection pressures of 30MPa and 50MPa, the injection rate was higher at 50 MPa, and the spray development (penetration) was also higher in the same elapsed time. The peak in-cylinder pressure and rate of heat release showed a tendency to decline as injection timing was delayed, and the peak in-cylinder pressure and rate of heat release were slightly higher for higher injection pressures. Higher injection pressures also reduced the mean effective pressure, while the indicated mean effective pressure and torque increased as injection timing was delayed to TDC. Nitrogen oxides had a peak level at injection timings of $BTDC20^{\circ}$(30MPa) and $BTDC15^{\circ}$(50MPa); carbon monoxide emissions were reduced by delaying injection timing from $BTDC30^{\circ}$.

• Journal of the Korean Geotechnical Society
• /
• v.39 no.10
• /
• pp.5-18
• /
• 2023

The construction timeline for earthworks can be significantly reduced by substituting the conventional layer-by-layer compaction using a vibratory roller with single-layer compaction through the rapid impact compaction (RIC) method. Dynamic load compaction is well-suited for coarse-grained soils like sand. However, as the supply of sand, the primary reclamation material, becomes scarcer, the utilization of soil with fines is on the rise. To implement the dynamic load compaction, such as RIC, with reclaimed materials containing fines, it's imperative to determine the effective improvement depth. In this study, we assess the impact of the RIC method on the effective improvement depth for clean sand and public fill with fines, comparing field test results before and after RIC application. Our focus is on the cone resistance (q_c) as it pertains to compaction quality control criteria. In conclusion, it becomes evident that standardizing the cone resistance is vital for the quality control of various reclaimed soils with fines. We have evaluated the compaction quality control criteria corresponding to a relative density (Dr) of 70% for clean sand as Q_tn,cs = 110. As a result of this analysis, we propose new quality control criteria for q_c, taking into account the fines content of reclaimed soils, which can be applied to RIC quality control.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.37 no.8
• /
• pp.1018-1024
• /
• 2008

The objective of this study is to compare the physicochemical properties and release characteristics of red ginseng (A) and tissue cultured mountain ginseng (B) extruded tissue cultured mountain ginsengs at barrel temperatures 110 (C) and $120^{\circ}C$ (D) to produce tissue cultured mountain ginseng-like comercial red ginseng by extrusion process. Extrusion process variables, water content and screw speed were fixed at 25% and 200 rpm, respectively. In the results, reducing and total sugar content were found to be relatively higher in A. The acidic polysaccharides content of B was the lowest among the ginseng samples. Acidic polysaccharide was increased 3 times by extrusion process. A and B were three times higher at maximum than C and D in polyphenolic compound. Polyphenolic compound content was relatively low by extrusion of ginsengs. Amino acid contents of B, C and D were $35{\sim}42\;{\mu}g/mL$; in contrast, A contained $25\;{\mu}g/mL$. The crude saponin content of C and D were higher than A and B.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.15 no.6
• /
• pp.291-296
• /
• 2015

The tire damage classification method is researched on the periodicity detection of ramdomness ultrasonic signals to occur at the driving vehicle tire. Setting method of adaptive threshold is proposed in order to valid pulse detection by tire damage in ultrasonic noise on the road and used low pass filter for decrease signal ramdomness as preprocessing. Time interval of detected pulse is setted the density function depend on the vehicle's speed and the method of tire damage detection is proposed that measuring the first peak's time of time density function.The result of time density function in case of one damage material, the first peak's time is measured within the error limit of tire's rotation period, 169.8ms and 97.9ms and 81.8ms, about the speed of 50km/h and 80km/h and 100km/h. In case of more than one damage material, the sum of each peak's time is measured within the error limit of tire's rotation period about the speed.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.22 no.1
• /
• pp.14-21
• /
• 2002

The development of a new experimental method is required to easily observe the growth behavior of fatigue cracks. To satisfy the requirement, an image processing technique was introduced to fatigue testing. The length of surface fatigue crack could be successfully measured by the image processing system. At first, the image data of cracks were stored into the computer while the cyclic loading was interrupted. After testing, crack length was determined using an image processing software which was developed by authors. Various image processing techniques like a block matching method was applied tc the detection of surface fatigue cracks. By comparing the data measured by the image processing system with those by the manual measurement with a microscope, the effectiveness of the image processing system was established. If the proposed method is used to monitor and observe the crack growth behavior automatically, the time and efforts for fatigue test could be dramatically reduced.

• Korean Chemical Engineering Research
• /
• v.43 no.5
• /
• pp.595-602
• /
• 2005

In order to purify diethylene glycol as main impurity included in p-dioxanone, SLE (solid-liquid equilibria) and mixture density on two components system of p-dioxanone and diethylene glycol were measured and a layered melt crystallization with seed has been applied. The SLE of p-dioxanone and diethylene glycol were a simple eutectic system and the temperature and PDX concentration at eutectic point were 0.08 and 246 K, respectively. Densities of their binary mixtures were well fitted by the best correlation equation, ${\rho}_l=0.405+1.361x+0.002T-0.004xT$. In the melt crystallization, the growth rate (G) was proportional to the 1.5th power of the subcooling degree. The effective distribution coefficient ($K_{eff}$) as the degree of impurity removal was observed to increase with increasing the growth rate and initial p-dioxanone concentration. And also, $K_{eff}$ was correlated with Z function using Wintermantel's model such as $K_{eef}=-0.0604+6.392{\times}Z$. Finally, PDX purity through the optimization of this process can be obtained over 99%.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.5
• /
• pp.137-142
• /
• 2017

The development of medical devices based on the theory of tranditional Korean medicine is increasing due to population aging and emerging demand for medical services. Various clinical trials are being conducted to ensure the clinical effectiveness of the developed medical devices, and the importance of systematic management of variously collected information in this process is increasing. In this paper, we designed and constructed the database that can systematically manage the medical information of the patient and the pulse measurement information in conducting clinical trials by using pulse analysis system which is a representative diagnostic method of traditional Korean medicine. The constructed database can be efficiently used for the verification of existing algorithms or developing new algorithms through the quality control of various information and measured data on clinical trials. It also has several advantages in the control of clinical data. The results of this study can contribute to the establishment of Korean medical device data standard for the construction of integrated database management system that can share information with different kind of pulse analysis system and other bio-signal measuring devices.

• Journal of the Korean Chemical Society
• /
• v.27 no.3
• /
• pp.178-182
• /
• 1983

The conductances of sodium, potassium, ammonium, tetramethylammonium, and tetraethylammonium iodides, picrates(Pic) of sodium and potassium, and tetrabutylammonium tetraphenyl-boride have been measured in ethylene carbonate-acetone mixtures at $25{\circ}C$. The limiting equivalent conductances of the electolytes were computed by Fuoss-Kraus equation and the order was $(C_4H_9)_4NB(ph)_4 at any composition of the mixtures. The dissociation constants of the salts showed that the mixtures are good ionizing solvents for the salts. The order of limiting ionic equivalent conductance, $Na^+, is consistent with exactly the reverse order found for solvation number. Effective solvated radii calibrated by the Nightingale method showed that picrate ion seems to be unsolvated and that iodide ion seems to be solvated to some extent in the mixtures.

• The Transactions of the Korea Information Processing Society
• /
• v.13 no.5
• /
• pp.221-226
• /
• 2024

In information retrieval, queries come in various types, ranging from abstract queries to those containing specific keywords, making it a challenging task to accurately produce results according to user demands. Additionally, search systems must handle queries encompassing various elements such as typos, multilingualism, and codes. Reranking is performed through training suitable documents for queries using DeBERTa, a deep learning model that has shown high performance in recent research. To evaluate the effectiveness of the proposed method, experiments were conducted using the test collection of the Product Search Track at the TREC 2023 international information retrieval evaluation competition. In the comparison of NDCG performance measurements regarding the experimental results, the proposed method showed a 10.48% improvement over BM25, a basic information retrieval model, in terms of search through query error handling, provisional relevance feedback-based product title-based query expansion, and reranking according to query types, achieving a score of 0.7810.