• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.4
• /
• pp.321-327
• /
• 2017

In this study, to investigate the shape of the back bead as a weld quality parameter and to select the optimal condition of the root-pass TIG welding of a horizontal butt-joint, an experimental design and the response surface method (RSM) have been employed. Three parameters are used as input variables, which include the base current, peak current, and welding speed. The back bead width is selected as an output variable representing the weld quality, the target value of the width is 5.4 mm. Conducting the experiments according to the Box-Behnken experimental design, a $2^{nd}$ regression model for the back bead width was made, and the validation of the model was confirmed by using the F-test. The desirability function was designed through the nominal-the-best formula for the appropriate back bead width. Finally, the following optimal condition for welding was selected using the RSM: base current of 0.9204, peak current of 0.8676, and welding speed of 0.3776 in coded values. For verification, a test welding process under the optimal condition was executed and the result showed the back bead width of 5.38 mm that matched the target value well.

• Journal of the Korean Institute of Gas
• /
• v.16 no.3
• /
• pp.48-53
• /
• 2012

The purpose of this paper studies the failure cases including with system of liquefied phase injection in liquified petroleum gas vehicle. The first case, resulting with inspection the injector of LPG, it occasionally certified the injection damage phenomenon that the fuel efficiency(km/l) was decreased to 5% by carbon deposit with injector hole when the driver operates the vehicle. The second case, it certified the interference phenomenon of air flow with carbon deposit in ISA system control for idle speed of engine and throttle body suppling air into engine. As a result, the fuel efficiency was decreased 7%. The third case, the outer air during intake stroke was intermittently flowed in this gasket gap because of weaken adhesion power phenomenon for cylinder block by intake manifold gasket tearing. Consequentially, it certified the decrease for fuel efficiency to 3% by risen the amount of fuel injection as the air inflow quantity. These failure examples reduced the power performance of engine and the fuel efficiency of vehicle. It have to minimize of failure phenomenon preparing through quality management.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.10a
• /
• pp.736-737
• /
• 2011

This article proposes a POD system framework which creates templates by using the Web service environment with good accessibility, provides them so that users can easily edit them, and uses COM ports following Web standard capable of real-time printing with the same quality as edited files. The characteristic of framework proposed in this article is that it creates programs which users with basic skill in Internet use can learn and use relatively easily when compared with existing specialized editing programs and which allows users to print real-time such files as personally created by them in the same quality as on the screen, and thereby enhances accessibility there of.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.6
• /
• pp.478-487
• /
• 2003

In this paper, a type and special feature of Multi-level inverter used in medium-voltage and high-capacity motor driver is introduced. Especially, a power quality and structural advantages of H-Bridge Multi-level inverter is described. It presented the specific structure of power circuit, design method, controller composition and PWM techniques of the cascaded H-Bridge Multi-level inverter which is developed. The feasibility of the developed product based on 3,300V lMVA 7-level H-bridge inverter was studied by experiments and we get conclusion that 1)generate of near-sinusoidal output voltage; 2)is low dv/dt at output voltage; 3)reduce the harmonic injection at input; Experiment demonstrate that it is very economical in productivity because of using the existing production technique and examination equipment, and has the reliability and a good maintenance due to the structure of Power Cell unit combination as well as low cost IGBT.

• The Transactions of the Korea Information Processing Society
• /
• v.4 no.8
• /
• pp.2070-2079
• /
• 1997

In this paper, we proposed the FNCAC (fuzzy neural call admission control) scheme of the ATM networks which used the benefits of fuzzy logic controller and the learning abilities of the neural network to solve the call admission control problems. The new call in ATM networks is connected if QoS(quality of service) of the current calls is not affected due to the connection of a new call. The neural network CAC(call admission control) system is predictable system because the neural network is able to learn by the input/output pattern. We applied the fuzzy inference on the learning rate and momentum constant for improving the learning speed of the fuzzy neural network. The excellence of the proposed algorithm was verified using measurement of learning numbers in the traditional neural network method and fuzzy neural network method by simulation. We found that the learning speed of the FNCAC based on the fuzzy learning rules is 5 times faster than that of the CAC method based on the traditional neural network theory.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.8
• /
• pp.18-24
• /
• 2017

The process of transmitting messages through a medium with a limited bandwidth or channel dispersion inevitably involves signal distortion and noise influxes, resulting in the degradation of transmission quality due to the inter-symbol interference and additional noise, which increases the error rate of the received symbols. The main role of the equalizer is to remove the channel distortion and noise from the received signal to recover the transmitted messages. A number of studies on the equalizer composed of a combination of linear filter and error control coding have shown that they played a key role in enhancing the transmission efficiency, which is essential for digital communication. This paper proposes a new algorithm to correct the residual symbol errors in the message signal. In general, equalizer performance improvement algorithms were developed to improve the initial convergence speed or steady-state error. In this paper, however, the equalizer input signal was reconstructed using the equalizer decision symbols and the channel estimates to directly correct the decision errors by analyzing the statistical characteristics of the difference signal between the actual received signal and the reconstructed signal.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.4
• /
• pp.302-306
• /
• 2006

The improvement of load following operation of the thermal power plant is influenced to the electrical quality. Analysis of boiler, turbine, and governor system, and the study of control algorithm are necessarily preceded. The thermal power plant is operated by various control systems. In the case of faulty governor system, it takes long days to solve the problem and impossible to repair the mechanism without outage. A non-planned outage is taken into consideration because of economical power production. The paper introduces the followings; In case of system-frequency drop during long term, at 500MW thermal power plant, the generator output was drop. To clear this problem, the control logic is modified with analysis of trend and control algorithm. As a result system frequency drop is prevented during the long tenn and the electric grid operation is improved.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.329-330
• /
• 2006

본연구에서는 초음파 모터 등의 고출력 액츄에이터에 응용 가능한 $0.4Pb(Ni_{1/3}Nb_{2/3})O_3$-$0.6Pb(Zr_{0.405}Ti_{0.595})O_3$ + 0.25wt% $Fe_2O_3$ 조성시스템에 $MnO_2$ (0~1 wt.%)첨가하여 압전, 유전특성 및 미세구조에 관해 고찰하였다. 본조성을 $1125{\sim}1175^{\circ}C$ 온도에서 2시간 소결하여 시편을 제조하였으며 이의 결정구조 및 미세조직을 분석하였다. $MnO_2$ 첨가량 증가에 따라 압전 상수와 전기기계결함계수는 감소하였으며, 기계적 품질계수는 0.5 wt% 첨가시까지 증가하였으나 첨가량이 그 이상 증가함에 따라 감소하였다. 압전특성은 $1125^{\circ}C$에서 소결한 $MnO_2$ 0.5wt%조성에서 ${\varepsilon}r$ = 2040, kp = 0.66, $d_{33}$ = 504, Qm=438의 우수한 특성을 나타내었다.

• Journal of radiological science and technology
• /
• v.41 no.1
• /
• pp.61-66
• /
• 2018

The recent 3D printing technology is used in various medical, manufacturing, and education fields and is more efficient in terms of production process, time, and cost than existing production. Especially in fracture surgery, interest and research have been focused on improving accuracy, shortening of operation time and recovery time, and reducing reoperation. However, because of the financial and technical problems of the 3D printer and the file conversion program, the 3D printing is made directly at the hospital, and it is not generally used for diagnosis of fracture and surgical research. In this study, to solve those problems, clavicle CT imaging was switched into Osirix Open Source DICOM Viewer, Stereolithography file conversion programs and commercial Terarecon 3D DICOM Viewer, file conversion programs, and then clavicle fracture model was directly made through 3D printer of fused filament fabrication wire additive processing method, and then the accuracy of the shape was compared and analyzed. Clavicle fracture models printed in two methods were blind-tested on clinicians of general hospitals' orthopedics and radiologic technicians with over 10 years of experiences, and then their analysis opinions of resolution reviews were analyzed. The result showed no difference. The 3D printing model with open source DICOM STL file conversion program used was applicable to clinical, so it is considered useful in precision diagnosis of fracture and operation plans.

• Journal of the Korea Society of Computer and Information
• /
• v.24 no.11
• /
• pp.71-78
• /
• 2019

Most 3D displays that are currently in the market adopt the binocular disparity method creating a different image for the left and right eye for a 3 dimensional effect. However, commercialized 3D image output devices lack in performance making it uncomfortable for the viewer and restrict the viewer to certain positions. In this paper, we propose a single-cell polarized lens type stereoscopic system which has a smaller viewing angle and reduced crosstalk, with improved light penetration compared to existing double-cell structures; and analyzed the single-cell polarized lens type stereoscopic system properties, and conducted an effect analysis of performance improvement compared to the dual-cell type. Results showed that the single-cell type had a 25% improved performance, and the 3D crosstalk index which is an important index for quality characteristics of stereoscopic systems, increased over about 37%, compared to the dual-cell type.