• Aerospace Engineering and Technology
• /
• v.1 no.2
• /
• pp.113-122
• /
• 2002

A numerical analysis on the uniformity of propellant injection velocity of KSR-III has been carried out to give design improvements. Injector holes were approximated as porous media with the same pressure drop . The injection velocity is higher at the opposite side of the inlet for both LOX and fuel due to the static pressure rise in the stagnation region. Flow passages at the vertical circular plate in the LOX dome increase the uniformity of LOX injection. Little change was observed in the injection uniformity and pressure drop for the slanted LOX passage. Also provided were the O/ F ratio distributions from the oxidizer/ fuel injection velocity analysis.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.622-627
• /
• 2017

In this study, the numerical analysis of propellant supply manifold of a sub-scale model combustor with the same combustion and acoustic resonance conditions as the real combustor was carried out. The analysis of the results is based on the shape of the manifold and the number and type of inflow channels. The manifold form of the main propellant was rounded so that the recirculation area was small and easy to manufacture. The liquid oxygen mainfold included a distributor to uniformly supply the flow, and since the kerosene manifold was directly in contact with the flame side, the inflow channel was formed at a radial $360^{\circ}$ so as to minimize the recirculation region. The liquid nitrogen manifold was configured as a radial inflow channel to reduce the velocity difference near the injector.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2000.11a
• /
• pp.4-4
• /
• 2000

KSR-III 과학로켓 개발사업의 한 분야인 추진기관 연구에 있어 가장 중심이 되는 것은 제작된 연소실의 시험/검증이라고 할 수 있다. 여러 단계의 시험 가운데에서도 엔진의 특성을 제 1차 적으로 파악하고, 시험 대상물인 엔진을 스탠드에 장착하여 시험이 가능토록 하기 위해서 모사 추진제(물) 혹은 실제 추진제를 사용하여 수력학적 특성을 알아내는 것은 매우 중요하다. 이를 위해 engineering model 엔진(이하 EM)에 대하여 액체 산소 배관은 액체 산소를, 스탠드 사정상 케로신 배관은 액체 질소를 사용한 비연소 시험을 수행하였으며, 이러한 일련의 비연소 시험을 통해 산화제 및 연료 매니폴드 각각에 대한 차압과 매니폴드를 채우는 시간을 측정하여 점화 사이클을 정의할 수 있었다.(중략)

• Journal of the Korean Society of Propulsion Engineers
• /
• v.8 no.3
• /
• pp.68-74
• /
• 2004

Effect of fluctuation imposed on the inflow to LOX manifold of liquid rocket has been analyzed numerically. Time-varying fluctuation was idealized by the sinusoidal signal and three different representative frequencies were considered. It was found that all the frequencies tested produced the consistent flow reactions in the manifold in that the place close to the region of infection showed oscillatory flow rate through injector orifices in phase with the inflow fluctuation whereas the other side exhibits characteristics which are out of phase.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.145-148
• /
• 2009

Combustion tests of a fuel-rich gas generator had been conducted using the assembly of a powerpack. A gas generator is prone to longitudinal modes of combustion instabilities in a powerpack due to the increase of a characteristic length. It has been observed that the orifice inserted at the exit of the gas generator suppresses a longitudinal combustion instability. The intensities of pressure fluctuations in the manifolds and the chamber increase quadratically with a chamber pressure. Pressure fluctuations in the fuel manifold reveal two-fold strength greater than those in the oxygen manifold and the chamber. Frequency analysis indicates nonlinear characteristics inherent in the pressure fluctuations in the fuel manifold.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.8 no.2
• /
• pp.1-9
• /
• 2004

The flow in the LOX manifold of liquid rocket (KSR-III) has been analyzed using a CAE technique with an objective of modeling injector orifices in order to reduce the computational cost for the flow analysis without much losing the accuracy of capturing the flow physics. The numerical result shows that the flow just above the injector orifices is not uniformly distributed in terms of pressure and mass flow rate in case pre-distributors are not equipped inside the manifold. This non-uniformity of mass flux is attributed to the presence of large-scale flow patterns. Several boundary conditions which were designed to effectively replace the presence of injector orifices have been tested and it was found that a simple modeling can be possible by mimicking the actual shape of the orifices.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.16 no.1
• /
• pp.36-44
• /
• 2012

Multi-injector rocket engine using high-concentrated hydrogen peroxide and kerosene was designed and manufactured. Design requirements of a rocket engine were determined and main geometrical parameters of rocket engine were determined on the basis of fundament. Six coaxial swirl injectors were mounted on the multi-injector engine. Flow analysis in the hydrogen peroxide manifold was performed to minimize stagnation and recirculation zones. Finally, the optimized hydrogen peroxide manifold was manufactured and cold flow test was carried out to confirm mass flow rate per uni-element, spray pattern and atomization characteristics. The results of cold flow test showed that the mixing head design process was successful and enough to use as a essential database for the development of a full-scale engine.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.3
• /
• pp.16-23
• /
• 2008

Flow analyses have been performed to investigate the uniformity of propellant flow through the oxidizer manifold of a 30 tonf full-scaled combustor. Injectors were simulated as porous medium layers of equivalent pressure drops. The uniformity of oxidizer propellant has been analyzed for various diameters of holes in vertical/horizontal distributors and configurations of oxidizer inlet to propose an improved design solution. It has been proven that the mass flow uniformity were improved by adjusting the holes in vertical/horizontal distributors.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.5
• /
• pp.22-30
• /
• 2015

A gas generator which generates turbine driving gas by burning a part of propellants is used in an open cycle liquid rocket engine and as a main component of an open cycle liquid rocket engine autonomous hot firing tests are required to investigate the combustion performance and characteristics of the gas generator. However, since the combustion gas generated by a gas generator is choked at the turbine nozzle in the turbine manifold, it is necessary to consider the internal volume of turbine manifold as well as that of the gas generator for correct investigation of the combustion performance, characteristics, and acoustic characteristics of the gas generator. Therefore, in the paper hot firing test results of a gas generator with a turbine manifold simulator are described and characteristic prediction using the autonomous test of a gas generator is explained.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2000.04a
• /
• pp.1-1
• /
• 2000

액체로켓엔진에 있어서 연소실로 공급된 추진제의 안정적인 점화를 위해 추진제 공급의 선점 시간을 결정하기 위한 실험이 수행되었다. 사용된 추진제는 Jet A-1과 액체 산소이고 추진제의 공급은 가압 방식이다. 135$^{\circ}$의 각을 갖고 배열된 인젝터는 FOOF 타입의 비동류형 충돌형 인젝터이고 연소실 압력이 200psi가 되도록 설계되었다. 현재의 실험은 점화원으로서 TEAL(triethylaluminum)을 사용하여 쿼드렛 타입의 점화기의 안정적 점화 여부를 검증하는 것도 포함된다. 점화 특성 파악을 위해 인젝터 상류의 매니폴드 압력, 연소실 압력이 측정되었고 점화 과정 및 정상 상태로의 천이 과정에 대한 간접적 증거로서 화염 길이가 측정되었다.