• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1997년도 제25회 춘계학술대회
• /
• pp.91-100
• /
• 1997

In this paper the linearzed stiffness and damping coefficients of tilting pad thrust bearing are calculated by the perturbation method. The coefficients are obtained for a wide range of pivot positions. The effects of exciting frequency and pad mass on stiffness and damping coefficients are investigated. Critical frequencies due to the tilting motions of the pad are presented and are shown to be strongly influenced by the pivot position and pad mass.

• Tribology and Lubricants
• /
• 제16권4호
• /
• pp.274-281
• /
• 2000

In this paper, linearized dynamic characteristics of parallel line pivoted pad thrust bearing (here-inafter refer to PLP thrust bearing) was analyzed by perturbation method with inlet pressure. Inlet pressure and excitation frequency influence dynamic characteristics of PLP thrust bearing at all operating conditions, such as angular pivot position, mass of pad. Therefore, the characteristics have to be analyzed with inlet pressure, excitation frequency, mass of pad and thickness of pad. Otherwise, the analysis may be over or under estimate.

• Tribology and Lubricants
• /
• 제15권1호
• /
• pp.24-28
• /
• 1999

This paper describes a new pivoting technique to improve bearing performance in pivoted pad thrust bearings. This new technique adjusts the pivot line in a line pivoted pad thrust bearing to be parallel to the trailing edge of a sector shaped pad. Bearing performance factors such as load carrying capacity, frictional torque and flow rate are numerically investigated for conventional point-pivoted and line-pivoted pads and for the new parallel-line pivoting technique. It is shown that the load carving capacity can be maximized with the new technique.

• Tribology and Lubricants
• /
• 제13권3호
• /
• pp.33-41
• /
• 1997

In this paper the linearized stiffness and damping coefficients of tilting pad thrust bearing are calculated by the perturbation method. The coefficients are obtained for a wide range of pivot positions. The effects of exciting frequency and pad mass on stiffness and damping coefficients are investigated. Critical frequencies due to the tilting motions of the pad are presented and are shown to be strongly influenced by the pivot position and the pad mass.

• 한국항공우주학회지
• /
• 제33권6호
• /
• pp.92-99
• /
• 2005

30톤 추력급 터보펌프에 대한 회전체 동역학 해석이 수행되었다. 연료펌프와 터빈에 의해서 유발되는 공력 및 수력 하중이 볼 베어링과 비접촉식 실의 강성 및 감쇠 예측을 위하여 고려되었다. 임계 속도의 분리 안전 여유와 회전체 부품의 팁 변위를 예측하기 위하여 임계 속도 해석과 질량 불평형 응답 해석이 수행되었다. 정확한 해석을 위하여 3차원 유한요소법을 사용하였고 1차원 전달함수 행렬법의 결과와 비교하였다. 탄성 링을 추가적으로 장착함으로써 베어링 지지부의 강성 제어를 통하여 충분한 공진 분리 여유의 확보가 가능함을 확인하였다.

• 대한조선학회논문집
• /
• 제52권1호
• /
• pp.61-69
• /
• 2015

In the beginning of the 1990's, numerous shaft bearing damages, especially in aft stern tube bearing, were reported. The main reasons of bearing damages were estimated that hull deflections have been increased by more flexible hulls and propeller dynamic loads have not been considered in shaft alignment. After that time, studies to take into account hull deflections in shaft alignment have been actively carried out, but for the latter leave much to be desired. In this study, the effects of the propeller forces on the propeller shaft bearing have been investigated by estimating thrust eccentricity as reasonable as possible although some assumptions to simulate turning of ship were introduced. Three dimensional nominal wake to estimate thrust eccentricity have been calculated by using CFD analysis and model test in the towing tank. This study presents the procedure to estimate the propeller eccentric forces and their influence on the stern tube bearing for a container carrier. As a result, it has been found that the lateral propeller forces in turning condition should be considered in shaft alignment to prevent shaft bearing damages.

• 한국항공우주학회지
• /
• 제34권6호
• /
• pp.92-97
• /
• 2006

케이징 구조 유연성을 고려한 30톤 추력급 터보펌프에 대한 임계 속도 해석이 수행되었다. 로터와 케이징을 포함한 전체 모델에 대한 3차원 유한요소법이 회전체 동역학 특성을 예측하기 위하여 적용되었다. 케이징 구조 유연성의 영향을 고찰하기 위하여 로터 단독 모델과 고정-고정 및 자유-자유 경계조건을 갖는 로터-케이징 연계 모델에 대한 수치 해석이 이루어 졌다. 무부하 하중 조건과 부하 하중 조건에서의 볼 베어링 강성이 각각 진공 조건과 실제 엔진 장착 조건에서의 작동을 모사하기 위하여 사용되었다. 수치해석 결과로부터 케이징 구조 유연성의 영향이 터보펌프의 임계 속도를 감소시킴을 확인하였다. 특히, 높은 베어링 강성을 갖는 부하 로터 조건에서 낮은 베어링 강성을 갖는 무부하 로터 조건에 비하여 더 많은 영향을 받음을 알 수 있었다.

• Tribology and Lubricants
• /
• 제11권1호
• /
• pp.20-26
• /
• 1995

Most magnetic bearings are based on the attractive force between the magnets and ferrous materials. One of the disadvantages of such attractive type magnetic bearings is the instability so that an active control device is necessary to operate bearing successfully. In this study a repulsive type magnetic bearing is analyzed which uses eddy current as a force source. The load capacities are analyzed for the various gap sizes, the rotor velocities and the frequencies of current supplied to electromagnet. Analytic Results show that as the gap size decreases, the levitation and drag forces increase, while the number of poles increasqs, the drag force decreases in the higher linear velocity region. Experimental results show that as the gap size decreases the levitation and the drag force increase, and as the velocity of rotor increases, the drag is larger than the levitation force up to certain velocity. But after that, the levitation is larger than the drag force. As the frequency of the current increases the levitation and drag decreases while the thickness of rotor gets thicker the forces decrease because of increase in eddy current loss.

• 소성∙가공
• /
• 제9권5호
• /
• pp.478-485
• /
• 2000

This study aims to Improve the productivity in forming of flanged thrust engine bearings from two kinds of laminated sheet materials by integrating the forming processes or by reducing the number of the subsequent sizing and machining processes or by modifying the forming tools used. For steel-Al rolled blank, a design scheme for the one-step forming operation and the geometry of the tool set required is suggested and is verified its usefulness by the finite element simulation. And for steel-Cu sintered blank, the results of experiment and finite element analysis show that it is possible to improve the dimensional accuracy of formed products and to reduce the number of sizing processes just by modifying the shape and dimensions of initial blanks and flange forming dies, and by controlling the spring force.

• Journal of Advanced Marine Engineering and Technology
• /
• 제22권1호
• /
• pp.85-91
• /
• 1998

In this paper, an influence of inlet pressure on the running characteristics of tilting pad thrust bearing is studied by a numerical analysis. The inlet pressure is obtained from the extended Bernoulli equation including the loss coefficient which is varied with the operating conditions. The running characteristic parameters such as the minimum film thickness, the film pressure and the film thickness ratios are calculated for various runner speeds with constant load in particular two pivot positions. The results are shown that the inlet pressure has a large influence on the minimum film thickness and other running characteristic parameters.