• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.2
• /
• pp.177-183
• /
• 2005

The effluent quality is directly affected by the separation of biological solids in a final clarifier because the majority of discharged $BOD_5$ and SS are virtually dependent on the results of biological solids in the sedimentation tank effluent. If a final clarifier is effectively designed and operated, the desired goal of clarification for wastewater can be achieved together with the cost reduction in the treatment of wastewater. To this end flow characteristics and the removal efficiency of SS are numerically investigated especially by the change of the inlet position and the installation of baffle to improve the performance of a rectangular final clarifier. The 2-D computer program developed in a rectangular coordinates has been successfully validated against experimental residence time distribution(RTD) curves obtained by tracing radio-isotope. The lowering of the inlet position weakens the density current and induces the settling of SS in the front zone of a clarifier. Thus the decreased traveling distance of the sludge increases the removal efficiency of SS in the effluent. The inlet baffle installed in the front region of clarifier prevents the short circuiting flow and induces to flow into the dense underflow, which eventually improves the effluent quality. In the case of lower inlet position, however, installation of baffle results in degradation of effluent quality. Consequently it is strongly recommended that in-depth numerical study be performed in advance for optimizing a clarifier design and retrofitting to improve effluent quality in a final clarifier.

• 한국상하수도협회지
• /
• s.10
• /
• pp.52-55
• /
• 2005

• Journal of Wetlands Research
• /
• v.18 no.4
• /
• pp.357-362
• /
• 2016

Improvement of the solid-liquid separation efficiency in the secondary sedimentation tank of the biological treatment process, is known to be increasing effectiveness of the overall system operation. Sewage treatment plant effluent SS is composed of most organic substances. In order to reduce the SS component in the secondary sedimentation tank discharge, fine SS components constituting the heterogeneous should be increased by its own aggregation (self flocculation), so that can be deleted through their precipitation. So, it is improved through using the installation of double rectification wall in this secondary tank. In case, sewage is rapidly increased due to the daily change of the influent water, it was confirmed that suspended solids caused by the impact load are processed stably. Therefore, there is a need for a facility installation which can be its own aggregation for reduction suspended solids in secondary sedimentation tank.

• Proceedings of the Korean Environmental Sciences Society Conference
• /
• 2020.10a
• /
• pp.103-103
• /
• 2020

• Journal of Korea Water Resources Association
• /
• v.35 no.2
• /
• pp.213-220
• /
• 2002

This reserch was focused upon experimental study for wastewater reuse and conducted to evaluate optimum operating conditions of rapid filtration process such as filter flow rate, filtration time and backwashing condition for reuse of secondary-treated effluent using the pilot plant installed in real wastewater treatment plant. Also, the experiment on treatment char-acteristics of coagulant-added activated sludge process was performed to compare with activated sludge succeeded to rapid filtration. As the filtration velocity was 100m/day, the filtration time of the rapid filter connected with activated sludge system was revealed to 40 hours. Backwashing of filter was conducted by water wash and air scour. The optimum backwashing time and backwash flow rate were 10min and 10LPM, respectively. The quantity of backwashing water of the rapid filter was about 2% of total treated water.

• Journal of Korean Society of Environmental Engineers
• /
• v.39 no.5
• /
• pp.229-236
• /
• 2017

Flow characteristics analysis and tracer test simulations for the rectangular typed sedimentation basins, which have been operated at D_water treatment plant in Korea, were carried out using CFD (Computational Fluid Dynamics) techniques for design ($15,864m^3/day$) and operation flowrate ($33,333m^3/day$). Also, each efficiency of the sedimentation basin was evaluated by application of the Lagrangin technique on the assumption of the particles flowing into the inlet of the sedimentation basin. From the results of simulation, the mean velocity values for making the flow in the settling basin as a plug flow region were derived as 0.00193 m/s and 0.00417 m/s, respectively. In addition, ${\beta}$ (effective contact factor) values were calculated to be 0.51 and 0.46, and the Morrill Index values were 6.05 and 3.21, respectively for both flowrate conditions.

• Journal of Korea Water Resources Association
• /
• v.47 no.5
• /
• pp.483-490
• /
• 2014

The design procedures for a biological reactor and a secondary settling tank (SST) of an activated sludge system are based on the steady state design method (Ekama et al., 1986; WRC, 1984) and the 1-D flux theory design method (Ekama et al., 1997), respectively. This study combined both of the design procedures, to determine the optimum sludge concentration in the reactor and the best design with the lowest cost. The best design of the reactor volume and the SST diameter at the optimum sludge concentration were specified with varying wastewater and sludge characteristics, temperature, sludge retention time (SRT) and peak flow rate. The effects of the influent wastewater characteristics, such as substrate concentration and unbiodegradable particulate fraction, were found to be considerable, but the effect of unbiodegradable soluble fraction was to be negligible. The effects of sludge settling characteristics, were also significant. SRT, as an operating parameter, was found to be an important factor for determining the optimum sludge concentration. However, the effect of temperature was found to be small. Furthermore, for designing a large scale wastewater treatment plant, the number of reactors or SSTs could be estimated, by dividing the total reactor volume or SST area. The new combined design procedure, proposed in this research, will be able to allow engineers to provide the best design of an activated sludge system with the lowest cost.

• Journal of Korean Society of Water and Wastewater
• /
• v.27 no.4
• /
• pp.469-477
• /
• 2013

In order to investigate the influence of feed water inequity on the settling performance for parallel arranged upflow sedimentation basin in domestic G_WTP(Water Treatment Plant), CFD(Computational Fluid Dynamics) simulation were employed and ADV(Acoustic Doppler Velocimeter) measurements were carried out. From the results of both CFD simulations and ADV measurements, the differences among inlet flow rates to each inlet structure make turbulent energy dissipation uneven overall sedimentation basin. Especially local velocities in the near of both side wall were observed over the design overflow rate(74.4 mm/min). Also, it was confirmed that this inequity of inlet flow would exert an serious influence on the turbidity of settled water which is out from 8 troughs. Even though experimental velocities in full scale basin about 20% higher than the simulated, the results of ADV measurement were in good accordance with those of CFD simulations.

• Journal of Korean Society of Water and Wastewater
• /
• v.28 no.2
• /
• pp.217-223
• /
• 2014

In order to suggest the methodology for improving the equity of flow distribution in open channel with multiple outlet, CFD simulations were carried out for actual scale distribution channel being operated in domestic G_WTP(Water Treatment Plant). Also, before and after installing the longitudinal multi hole(diameter=250 mm, 116 holes) baffle suggested by this research, turbidity measurements data were collected for evaluating the effects of hydraulic modification for inlet flow equity. From the both results, total turbidity of settled water was lowered by 30 % and equity of flow distribution was improved about 60 % compared with before hydraulic structure modification.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2021.06a
• /
• pp.425-425
• /
• 2021

북평산업단지내 공공폐수처리시설(6,500톤/일)의 가동률은 30% 이하로 매우 저조하며, 폐수배출업체는 29개소로 그 수가 적어 배출오염부하량 비율에 따른 처리비용이 일부 업체의 경우 과도하게 부과되고 있는 실정이다. 입주업체 운영비용 부담을 저감하기 위해 해당 지자체에서는 운영비용의 65% 이내에서 일정금액을 지원하고 있으나, 동일업종에 대한 원인자비용부담금 비율의 경우, 동해시 A업체는 30.18%로 타 지역 B업체의 4.83% 보다 높은 것으로 나타났으며, 지자체 지원금을 제외한 순수 처리부과금의 경우 A업체가 2배 이상 큰 것으로 나타났다. 이에 북평산업단지 공공폐수처리시설의 전체 운영비 절감을 위한 효율적인 운영방안 마련이 필요하다. 따라서 본 연구에서는 북평산업단지내 공공폐수처리시설의 운영 및 관리현황을 검토하여 효율적인 운영방안을 제시하고자 하였다. 현재 운영시설에 대한 현황을 파악하고 관련 법률 및 계획등을 검토한 결과, 북평산단 지역은 하수처리 구역이 아닌 공공폐수처리구역으로 산업폐수의 공공하수도처리시설 연계처리 지침에 따라 인근 공공하수처리시설과의 연계처리가 불가한 것으로 나타났다. 또한, 환경부에서는 가동률이 저조한 처리시설에 대해서는 시설개선을 통한 방안을 제시하고 있어 현 처리시설의 공정개선을 통한 운영비 절감방안이 가장 효율적인 것으로 판단되었다. 이에, 현재 생물 반응조 후단에서 운영 중인 가압 부상조에 새로운 배관을 설치하여, 최초 침전지 유출수를 가압부상조 처리 후, 생물 반응조로 유입하고, 최종 침전 후 총인을 제어 할 수 있는 약품투입 시설을 설치하는 공정 개선 방안을 제시하였다. 이처럼 생물 반응조 이전에 가압부상조를 설치하고, 후단 가압 부상조 미운영시 공정개선 전·후에 따른 총 슬러지 발생량은 24.2%, 탈수케익 처리비용은 27.6% 절감할 수 있는 것으로 산정되었으며, 전체 처리시설에 대한 총 운영비 감소율은 13.4%로 분석되었다.