• Proceeding of EDISON Challenge
• /
• 2015.03a
• /
• pp.347-349
• /
• 2015

본 연구에서는 MOSFET 제작방법중 하나인 이온주입법에서 다양한 변수로 작용하는 도핑농도, 에너지주입, 바탕농도의 역할에 대해서 알아보고 채널길이가 감소함에 따른 단채널효과를 억제할 수 있는 최적점에 대하여 분석하였으며 Ion Implant 이차원 시뮬레이션값과 비교하였다. 결과적으로 농도와 에너지주입 그리고 채널길이에 따른 MOSFET의 최적화된 모델을 분석하였다.

• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.7
• /
• pp.495-502
• /
• 2013

This work was performed to investigate proper condition of coagulation treatment as UF process pretreatment that consider UF permeate flux and residual Al concentration. The coagulant used an alum as $Al_2(SO_4)_3{\cdot}16H_2O$ and PACl (r = 1.5) made this study. The experiment was tested in adjusting conditions such as alum dose, flocculation time and coagulation pH of seawater. Consequently, higher coagulant dose lead to elevation of UF permeate flux while residual aluminium also increased in condition of pH 8.0. The most suitable condition which has a good permeate flux and low residual aluminium, in this works, was coagulant dose of 0.7 mg/L (as Al, alum) and 1.2 mg/L (as Al, PACl) and coagulation pH 6.5. In addition, applying the flocculation time with 1.2 mg/L of PACI reduced. The flocculation time reduced UF permeate flux in using alum.

• Journal of Korean Society of Environmental Engineers
• /
• v.38 no.9
• /
• pp.482-496
• /
• 2016

Algal blooms of cyanobacteria (blue-green Algae) due to the eutrophication of rivers and lakes can cause not only the damage by its biological toxins but also the economic loss in drinking water treatment. The natural algae coagulant, a commercial product known as W.H. containing the algicidal and allelopathic material derived from oak, can control algal problems proactively through the coagulation flotation process. However, because there have been no applications of the process for pre-treatment in drinking water plants, we could find no report on the optimum injection dose of W.H.. In this study, we have conducted several sets of jar-tests while changing W.H. dose and concentration of chl-a for (1) Han-river samples and (2) subcultured cyanobacteria samples, and monitored the removal mechanisms of algae intensively. Based on these jar-test results, two linear equations with variables of chl-a and turbidity have been deduced to predict the optimal W.H. dose after the multiple regression analysis using IBM-SPSS. Also, prototypes of automatic control logic have been suggested to inject the optimal W.H. dose promptly in response to the variation of water quality.

• KSBB Journal
• /
• v.4 no.3
• /
• pp.253-258
• /
• 1989

It was investigated that the influent sugar concentration and the dilution rate have an influence on the ethanol fermentation characteristics at steady state in a chemostat culture of K. fragilis using Jerusalem Artichoke juice as substrate. And also the optimum condition of high ethanol productivity and low residual sugar output in the ethanol production by K. fragilis, was clarified to be given at a dilution rate of 0.22/hr and at an influent sugar concentration of 85g/l.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.449-449
• /
• 2010

유기발광소자(organic light-emitting diodes, OLEDs)는 저공정비용, 경량화, 가용성 및 대면적화 등의 장점으로 조명 분야와 디스플레이 분야로의 응용 가능성으로 인해 크게 주목을 받아 왔다. 이러한 OLED 소자의 고효율, 고휘도 및 저소비전력 등을 구현하기 위해서는 전극으로부터 전하 주입 층으로 효율적인 전하 주입이 요구된다. 즉, 각 전극의 폐르미 준위로부터 전하 전도준위대로의 전하주입 장벽이 없어야 한다. 본 연구에서는 홀 주입장벽이 없는 정공주입 층으로 $MoO_x$(molybdenum oxide)가 도핑된 NPB(N, N'-diphenyl-N, N'-bis(1-naphthyl)-1,1'-biphenyl-4,4'-diamine) 층을 사용하여 hole-only 소자를 제작하고 전류-전압 특성을 통해 양극으로부터 홀주입 층으로의 hole-ohmic 특성을 고찰했다. 또한, 전자 주입장벽이 없는 전자주입 층으로 $C_{60}$(fullerene)/LiF(lithum fluoride)의 이종 층을 사용하여 electron-only 소자를 제작하고 음극으로부터 전자주입 층으로의 전자 ohmic 특성을 조사했다. 또한, 전극으로부터 전하주입 층으로 ohmic 특성을 더 자세히 이해하기 위하여 전하주입 층의 자외선 광방출 스펙트럼(ultraviolet photoemission spectra)을 조사했다. 한편, glass/ITO/$MoO_x$-doped NPB (x%: x=0,25, 50 및 75; 5nm)/NPB (63nm)/$Alq_3$ (37nm)/$C_{60}$ (5nm)/LiF (1nm)/Al (100nm)로 구성된 all-ohmic OLED 소자의 발광특성은 $MoO_x$의 도핑 농도가 25%이상일 때 최적의 특성을 보여줬다. 이러한 현상은 정공주입 층에서 p형 도핑 농도의 증가에 따른 정공 농도의 증가에 기인한다. 또한 $MoO_x$의 도핑 농도의 증가에 따라 정공주입 층의 new gap state와 전극의 페르미 준위의 pinning에 기인한다. 25%의 $MoO_x$을 가진 OLED소자는 7.2V의 낮은 전압에서 $58300 cd/m^2$의 높은 휘도를 보여줬다.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.6
• /
• pp.406-413
• /
• 2012

Effect of three additives, chitosan, ferric chloride, and MPE50 on membrane fouling reduction was studied. They were introduced with various dosing rate into activated sludge, and changes in filtration resistance measured by the batch cell filtration test were evaluated. Both the filtration resistance and the specific cake resistance were minimized at 20 mg/g-MLSS with chitosan, 70 mg/g-MLSS with ferric chloride, and 20 mg/g-MLSS with MPE50 addition, respectively. Introduction of the additives into the activated sludge resulted in reduction of not only cake resistance, but also fouling resistance. However, the chitosan addition to three different activated sludge resulted in three different optimal dose of 10, 20, 30 mg/g-MLSS, respectively. This implies that the optimal dose is dependent on sludge characteristics rather than a constant value. Overdose above the optimal dosage always aggravated filterability in all cases. Zeta potential of sludge flocs, relative hydrophobicity, floc size distribution, soluble EPS concentration and supernatant turbidity were measured in order to analyze fouling reduction mechanism. Nearly neutral surface charge along with the largest particle size was observed at the optimal dose. This could be explained by particle destabilization and restabilization mechanism as positively charged additives were injected into sludge flocs of negative surface charge. Both soluble EPS concentration and supernatant turbidity also showed the lowest value at the optimal dose. These foulants are believed to be coagulated and entrapped in sludge flocs during flocculation. Chitosan and MPE50 which are cationic polymeric substances showed higher reduction in both soluble EPS and fine particles comparing with ferric chloride.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.31 no.4
• /
• pp.41-49
• /
• 2023

This study examined the effect of input substrate concentration on hydrogen production of microbial electrolysis cells. To compare the performance of MEC according to the input substrate concentration, six laboratory-scale MEC reactors were operated by sequentially increasing the input substrate concentration from 2 g/L of sodium acetate, to 4 g/L, and 6 g/L. The current density, hydrogen production, and SCOD removal rate were analyzed, and energy efficiency and cathodic hydrogen recovery were calculated to compare the performance of MEC. The maximum volumetric current density was obtained at 4 g/L condition (76.3 A/m³) and it decreased to 19.0 A/m³, when the input concentration was increased to 6 g/L, which was a 75% decrease compared to the 4 g/L input condition. Maximum hydrogen production was obtained also at 4 g/L condition (47.3 ± 16.8 mL), but maximum hydrogen yield was obtained at 2 g/L input condition (1.1 L H₂/g COD_in). Energy efficiencies were also highest in 2 g/L condition; the lowest result was observed at 6 g/L condition. Maximum electrical energy efficiency was 76.4%, and the maximum overall energy efficiency was 39.7% at 2 g/L condition. However, when the substrate concentration increased to 6 g/L, the performance was drastically decreased. Cathodic hydrogen recovery also showed a similar tendency with energy efficiency, with the lowest concentration condition showing the best performance. It can be concluded that operating at low input substrate concentration might be better when considering not only hydrogen yield but also energy efficiency.

• Journal of IKEEE
• /
• v.26 no.3
• /
• pp.333-340
• /
• 2022

Process and device simulations were performed to determine the optimal ion implantation conditions to prevent double snapback of high voltage operating DDDNMOS (double diffused drain N-type MOSFET) device for ESD protection. By examining the effects of HP-Well, N^- drift and N⁺ drain ion implantation on the double snapback and avalanche breakdown voltages, it was possible to prevent double snapback and improve the electrostatic protection performance. If the ion implantation concentration of the N^- drift region rather than the HP-Well region is optimally designed, it prevents the transition from the primary on-state to the secondary on-state, so that relatively good ESD protection performance can be obtained. Since the concentration of the N^- drift region affects the leakage current and the avalanche breakdown voltage, in the case of a process technology with an operating voltage greater than 30V, a new structure such as DPS or colligation of optimal process conditions can be applied. In this case, improved ESD protection performance can be realized.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2001.09a
• /
• pp.160-163
• /
• 2001

본 연구에서는 Fe$^{0}$ /$H_2O$$_2$ 시스템을 이용하여 디젤 오염토양의 산화처리효율과 경제성 향상을 위한 실험을 수행하였다. 앞선 연구결과에서 최적 pH조건은 3이었으며, 과산화수소와 철 분말의 양은 비례적으로 증가할수록 처리효율이 높게 나타났다. 1) 이번 연구에서는 pH조절에 따른 처리효율의 향상효과를 알아보기 위해 pH 값을 3으로 일정하게 유지하여 반응을 수행하였으며, 일정 철 분말 농도조건에서 과산화수소의 주입방법에 따른 반응변화를 살펴보기 위해 과산화수소를 여러 비율로 분할 주입하면서 실험을 실시하였다. 본 연구결과에 따르면 pH를 3으로 일정하게 유지함으로써 초기에만 pH를 3으로 조정한 이전의 연구에서 반응이 경과함에 따라 나타나는 pH상승에 따른 처리효율의 감소 효과를 줄며 전체적인 TPH 처리효율을 10%이상 높일 수 있었으며, 같은 양의 TPH 제거에 소모되는 과산화수소의 양을 20% 정도 줄일 수 있었다. 과산화수소의 분할주입에 따른 반응향상효과 실험에서는 5회에 걸쳐 분할 주입한 경우에 3시간 이후 경미한 반응성 향상효과를 얻을 수 있었다. 이러한 결과는 과산화수소를 분할하여 주입함으로써 한번에 주입한 경우에 비하여 유기물의 산화에 직접적으로 참여하지 않는 과산화수소의 scavenging 효과를 최소화할 수 있음을 보여주는 것이다. 따라서 최적 pH의 일정 유지와 과산화수소의 분할주입으로 철 분말을 이용한 펜톤유사반응의 처리효율과 경제성 제고 모두에 있어서 효과가 있음을 알 수 있었다.

• Plant Journal
• /
• v.11 no.2
• /
• pp.32-38
• /
• 2015

This study was conducted on combined cycle power plant consisting of HRSG with integral deaerator type to avoid tube failures of low pressure evaporator tubes. Based on the observation of pH variation at the discharge of boiler feed water pump by continuous pH measurement for a period of time, it was identified that pH of feed water is getting reduced as ammonia is distributed into vapor and liquid depending on the distribution ratio of ammonia in the LP drum after the deaerator. To solve this problem, the counterplan was prepared by reexamination of ammonia injection point and quantity. In conclusion, it was accomplished that 9.2~9.6 is the optimized pH range for boiler feed water by arranging additional piping for ammonia to inject directly to LP drum.