• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.1
• /
• pp.245-248
• /
• 2012

In this paper, the optimized growing conditions of PZT thin films on low temperature co-fired ceramics (LTCC) substrates are studied. The LTCC technology is an emerging one in the fields of mesoscale (from 10 um to several hundred um) sensor and actuator against silicon based technology due to low cost, high yield, easy manufacturing of 3 dimensional structure, etc. The LTCC substrates with thickness of 400 um are fabricated by laminating 100 um green sheets using commercial power (NEG, MLS 22C). The Pt/Ti bottom electrodes are deposited on the LTCC substrates, then the growing conditions of PZT thin films using rf magnetron sputtering method are studied. The growing conditions are tested under various rf power and gas ratio of oxygen to argon. And the crystallization and ingredient of PZT films are analyzed by X-ray diffraction method (XRD) and energy dispersive spectroscopy (EDS). The optimized growing conditions of PZT thin films are rf power of 125W, Ar/O2 gas ratio of 15:5.

• Korean Journal of Materials Research
• /
• v.8 no.1
• /
• pp.52-57
• /
• 1998

기존 산화물 투명전극에 비해 더욱 우수한 전기전도성을 가지는 다층구조의 투명전도막을 마그네트론 스퍼터링 장치를 이용해 제작하였다. 전기전도성을 극대화하기 위해 비저항이 가장 낮은 Ag 금속을 사용하고, 금속층의 상하부에 반사광을 재반사시키는 산화물층을 형성시킨 다층막구조를 이용하였다. Ag 금속막은 충분한 투과율과 전기전도성을 확보하기 위해 연속된 막을 이루기 시작하는 두께인 140$\AA$로 증착하였고, ITO 박막은 가시광 영역의 반사광을 재반사시키는 최적의 두께인 600$\AA$ 내외로 증차하였다. Ag 박막의 증착조건과 후속 ITO 박막증착공정은 Ag박막의 특성에 영향을 미치므로 다층막의 전기적, 광학적 특성은 이들 증착 조건에 민감한 영향을 받음을 확인하였다. 상온에서 Ag박막을 형성하고 ITO박막은 7mTorr의 낮은 압력에서 증착하여 제작한 투명전도막은 SVGA 급의 STN-LCD용 투명전극으로 사용 가능한 4Ω/ㅁ 이하의 낮은 면저항과 빛의 파장이 550nm일 때 85%이상의 투과도를 나타내었다.

• Korean Journal of Materials Research
• /
• v.5 no.6
• /
• pp.754-762
• /
• 1995

Strontium titanate(SrTiO$_3$) thin film was prepared on Si substrates by RF magnetron sputtering for a high capacitance density required for the next generation of LSTs. The optimum deposition conditions for SrTiO$_3$thin film were investigated by controlling the deposition parameters. The crystallinity of films and the interface reactions between SrTO$_3$film and Si substrate were characterized by XRD and AES respectively. High quality films were obtained by using the mixed gas of Ar and $O_2$for sputtering. The films were deposited at various bias voltages to obtain the optimum conditions for a high quality file. The best crystallinity was obtained at film thickness of 300nm with the sputtering gas of Ar+20% $O_2$and the bias voltage of 100V. The barrier layer of Pt(100nm)/Ti(50nm) was very effective in avoiding the formation of SiO$_2$layer at the interface between SrTiO$_3$film and Si substrate. The capacitor with Au/SrTiO$_3$/Pt/Ti/SiO$_2$/Si structure was prepared to measure the electric and the dielectric properties. The highest capacitance and the lowest leakage current density were obtained by annealing at $600^{\circ}C$ for 2hrs. The typical specific capacitance was 6.4fF/$\textrm{cm}^2$, the relative dielectric constant was 217, and the leakage current density was about 2.0$\times$10$^{-8}$ A/$\textrm{cm}^2$ at the SrTiO$_3$film with the thickness of 300nm.

• Journal of the Microelectronics and Packaging Society
• /
• v.12 no.1 s.34
• /
• pp.1-7
• /
• 2005

The effect of trimming process to adjust accurate resistance of a thin-film resistor was studied with respect to low temperature coefficient of resistance(TCR) and high precision. The characteristics of a thin-film resistor fabricated by sputtering were investigated depending on trimming condition and annealing temperature. Measured results showed that the characteristic of a thin-film resistor was degraded with increased trimming speed. However, an average resistance deviation and a TCR were improved to $0.26\%$ and 52.77[ppm/K], respectively, through annealing treatment. Also, thin-film resistors with 1 k$\Omega$ and 10k$\Omega$ showed better performance compared to a resistor with 100k$\Omega$. The Optimal trimming speed and annealing temperature were 20mm/sec and 539K, respectively, and under this optimal condition, a thin-film resistor with an average resistance deviation of $0.31\%$ and a TCR of below 10[ppm/K] was obtained.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.7
• /
• pp.7-14
• /
• 2009

In this paper, the effects of annealing conditions on the structural ((002) intensity, FWHM, d-spacing, grain size, (002) peak position), optical (UV peak, UV peak position) and electrical properties (carrier concentrations, resistivity, mobility) of ZnO films were investigated. ZnO films were deposited onto SiO$_2$/si substrates by RF magnetron sputtering from a ZnO target. The substrate was not heated during deposition. ZnO films were annealed in temperature ranges of $500\sim650^{\circ}C$ in the O$_2$ flow for 5$\sim$20 min. The film average thicknesses were in the range of 291 nm. The surface morphologies and structures of the samples were characterize by SEM and XRD, respectively. The optical properties were evaluated by photoluminescence (PL) measurement at room temperature (RT) using a He-Cd 325 nm laser. As the annealing temperature and time vary, the following relations were also observed: (1) proportional relationships among UV intensity (002) intensity, and grain size exist, (2) UV intensity is inversely proportional to FWHM, (3) there is no special relationship between UV intensity and electron carrier concentrations, (4) d-spacing is inversely proportional to (002) peak position, (5) UV peak position in the range of 3.20$\sim$3.24 eV means that ZnO films have a n-type conductivity which was consistent with that obtained from the electrical property, (6) the optimal conditions for the best optical and structural characteristics were found to be oxygen fraction, (O$_2$/(O$_2$+Ar)) of 0.2, RF power of 240W, substrate temperature of RT, annealing condition of 600$^{\circ}C$ for 20 min, and sputtering pressure of 20 mTorr.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.192-192
• /
• 2013

본 연구에서는 RF/DC 마그네트론 스퍼터링 시스템을 이용하여co-sputtering 방법으로 성장시킨 고이동도를 갖는Ge-doped $In_2O_3$In2O3 (IGO) 박막의 전기적, 광학적, 구조적 특성을 평가하고, 이를 유기태양전지와 유기발광다이오드에 적용함으로써 고이동도 IGO 투명전극의 소자 적용가능성을 타진하였다. GeO2 타겟에 인가되는 도핑 Power와 급속열처리 온도가 30 W, $500^{\circ}C$일 때, 최적화 된 IGO 박막으로부터 $2.8{\times}10^{-4}$ Ohm-cm의 낮은 비저항과 86.9% (550 nm)의 높은 투과도를 확보하였다. 뿐만 아니라 Near Infra-red (750~1,200 nm) 영역에서의 IGO투명전극의 광투과율이 결정질의 ITO보다 높은(약15%) 투과도를 보이는 것을 통해 IGO박막의 높은 LAS (Lewis Acid Strength) 값을 가지는 Ge 원소의 도핑이 NIR 영역의 광투과율 향상에 미치는 영향을 확인할 수 있었다. 최적 조건의 IGO 박막을 적용하여 Fill Factor 67.38%, Short circuit current density 8.43 mA/cm2, open circuit voltage 0.60 V, efficiency 3.44%의 유기태양전지 및 19.24%의 외부양자효율을 갖는 유기발광다이오드를 제작함으로써 결정질 ITO 전극(20.05%)을 대체할 수 있는 고투과, 고이동도 IGO 투명 전극 및 이를 이용한 광전소자 적용 가능성을 타진하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.7
• /
• pp.420-424
• /
• 2016

In this study, we developed photocatalytic technology to address the emerging serious problem of air pollution through indoor air cleaning. A single layer of $WO_3$ was prepared by using the dry process of general RF magnetron sputtering. At a base vacuum of $1.8{\times}10^{-6}$[Torr], the optical and electrical properties of the resulting thin films were examined for use as a transparent electrode as well as a photocatalyst. The single layer of $WO_3$ prepared at an RF power of 100 [W], a pressure of 7 [mTorr] and Ar and $O_2$ gas flow rates of 70 and 2 sccm, respectively, showed uniform and good optical transmittance of over 80% in the visible wavelength range from 380 [nm] to 780 [nm]. The optical catalyst characteristics of the $WO_3$ thin film were examined by investigating the optical absorbance and concentration variance in methylene blue, where the $WO_3$ thin film was immersed in the methylene blue. The catalytic characteristics improved with time. The concentration of methylene blue decreased to 80% after 5 hours, which confirms that the $WO_3$ thin film shows the characteristics of an optical catalyst. Using the reflector of a CCFL (cold cathode fluorescent lamp) and the lens of an LED (lighting emitting diode), it is possible to enhance the air cleaning effect of next-generation light sources.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.237-237
• /
• 2010

에너지소비와 엔진 부품의 마모문제를 해결하기 위해, soft-phase를 doping한 hard상의 coating에 대한 실험이 최근 중요한 연구 테마로서 진행 중이다. 특히 MoN-Cu coating은 미국 Argon 연구소의 Erdemer박사 등에 의해, 고온 및 상온 윤활성이 우수한 코팅층으로 보고된 이후 많은 연구가 진행되고 있다. 그러나 기존 연구는 Mo와 Cu의 원소타겟을 이용한 연구가 주력이 되었다. 높은 경도와 저온 고온에서의 낮은 나노 혼합물 코팅 종류는 일반적으로 Mo와 Cu와 같은 원소 합금을 이용한 다수 타겟을 이용한 공정에 의해 진행되어왔다. 이러한 복수의 타겟에 의해 증착 동안에는, 정확한 조성, 큰 크기의 시편들의 균일 증착을 조절하기가 쉽지 않다. 또한, 코팅층에 3번째 성분을 추가하기가 어렵다는 문제점이 있다. 본 연구에서는, 최상의 마찰계수와 표면경도를 보이는 MoN-Cu층을 형성시키기 위하여 합금으로 단일 타겟을 제조하였다. 이를 위한 최적 조성을 결정하기 위하여 Mo, Cu 단일 타겟을 이용한 Unbalanced Magnetron sputtering 법으로 다양한 Cu 함량의 MoN+Cu 합금을 제조하였으며, 이에 대한 경도 및 마찰계수 측정을 통해 최적의 Cu 함량을 결정하였다. 이러한 최적 조성의 Cu 타겟제조를 기계적 합금화와 Spark plasma sintering 기술을 이용하여 제작하였으며, 복수의 합금 타겟과 단일 합금 타겟으로 제조된 코팅층의 물성 비교를 통해 합금 타겟의 우수성 여부를 확인하고자 하였다. 증착된 두 조건의 물성을 비교 단일 타겟은 두가지 타겟으로 증착한 것보다 비슷한 조성에서 경도가 높았으며 경도가 비슷한 조성에서는 마찰계수가 낮았다. 또 입자는 10 at.% Cu 조성에 대해 단일타겟이 50nm 결정립을 갖는 반해 단일타겟은 측정이 불가능할 정도의 미세한 결정립을 가졌다. Erdemir의 연구 결과에 의하면, Cu 함량이 증가함에 따라 columnar 형태의 코팅층구조가 나노 구조로 변한다고 하였는데, 본 연구에서 복수의 원소 타겟에서는 확인이 안되었으며, 단일 합금 타겟에서 완벽한 featurless 형태의 코팅층 구조와 우수한 조도의 박막층을 얻을 수 있었다. 이렇게 제조된 다양한 코팅층에 대한 마찰계수 측정이 진행중이다.

• Journal of the Korean Magnetics Society
• /
• v.11 no.2
• /
• pp.45-49
• /
• 2001

Effects of multilayer structure and annealing condition on the soft magnetic properties of sputtered Fe/CoNbZr multilayers were investigated. We observed a minimum coercivity (1.1 Oe) at 5 nm thick Fe layer and the maximum permeability (2300) at 15 nm Fe layer and high saturation magnetization in the as-deposited state. As a result of increase of Fe grain size, coercivity increases with increasing Fe layer thickness. Degradation of ${\mu}$ at the thin Fe layer region may be due to the intermixed phase of high magnetostriction, such as CoFe. Optimum annealing condition was obtained through annealing at 300 $^{\circ}C$ for 40 min (${\mu}$=2500, H$\sub$c/=0.35 Oe). Enhancement of permeability was observed in the temperature range of 250∼300$^{\circ}C$. These results may closely be related with lowering the anisotropy energy by lattice deformation (0.4%) and enhanced uniaxial anisotropy.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.1
• /
• pp.107-112
• /
• 1999

The ZnSe/GaAs epilayers were grown by RF reactive sputtering. In order to obtain the optimum condition of the growth, we have studied the dependence of Ar pressure, input power of sputter, temperature of substrate, and the distande between substrate and target. Through the observation of the grown epilayer via electronic microscope, we confirmed that the layer's surface was uniform and the boundary of the substrate and the layer was well defined. The defotmation of lattice distortion and the distortion ratio were obtained by DCRC measurements. From mrasurements of photoluminescence, in the ZnSe/GaAs sample without injection of $N_2$gas, we found that the intensity of bound exciton $I_2$is stronger than that of $I_1$and the bound exiton $I_1$represents the deep acceptor level, $I_1\;^d$. On the other hand, in the ZnSe/GaAs sample with injection of$N_2$gas, the peak of$I_1$ was much higher than that of the $I_2$and the half width appeared to be narrow. We concluded that the p-type of ZnSe/GaAs epilayer was grown successfully, because of stronger peak of the bound exciton $I_1$due to the $N_2$dopping.