• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.515-516
• /
• 2011

송 배전 및 정보통신 설비, 건축물 등 모든 분야의 설비 및 인명 보호를 위해서는 반드시 필요하고 중요한 것이 접지이며, 접지 설계 시 대상 부지의 정확한 대지고유저항을 측정, 분석하는 것은 가장 중요하다고 할 수 있다. 본 대지고유저항 분석시스템은 이렇듯 중요한 대지고유저항을 기존의 수작업 분석방법이 아닌 시스템 반복계산에 의한 최적 curve 분석방법을 도입, 측정값의 신뢰도 평가 등을 이용한 측정값 분석으로, 분석값의 정확성을 높이고 분석시간을 단축함으로서 보다 정확하고 신속한 접지설계를 가능하도록 한다.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.17 no.6
• /
• pp.65-71
• /
• 1980

The Sn O2-Si Heterojunction sola cells are Prepared by vacuum deposition of SnO2 on N- and P-type Si - wafers arts the effects of annealing on the Solar cell characteiistics are presented. The existence of optimumannealins temperature for maximum open-circuit voltage and short - circuit current of the solar cell is observed. The optimum tomperature, when low resistivity (7- 2.3 [$\Omega$.cm]) P-and N-type Si -wafers are used, is 500 [$^{\circ}C$] End 400 [$^{\circ}C$] when high resistivity[41-58 [$\Omega$.cm]) P-type Si-wafers are used.

• Journal of the Korea Concrete Institute
• /
• v.14 no.3
• /
• pp.275-282
• /
• 2002

High fluidity concrete needs high dosage of superplasticizer to acquire sufficient fluidity and high contents of fine powder and viscosity agents to prevent segregation. But it requires high manufacturing cost and has difficult in quality control. Therefore, in this paper, determination of optimal mixture proportion of segregation type superplasticizer for high fluidity concrete and manufacturing high fluidity concrete by applying developed segregation reducing type superplasticizer are discussed using flowing concrete method. According to test results, as dosage of superplasticizer increases, it shows that fluidity and bleeding increase, while air contents and ratio of segregation resistance decrease. It also shows that adding viscosity agent into it reduce bleeding and improve segregation resistance. Dosage of AE agent into it containing viscosity agent recovers loss of air contents during flowing procedure. Combination of proper contents of superplasticizer, viscosity agent and AE agent make possible to develope segregation reducing type superplasticizer Compressive strength of high fluidity concrete applying flowing method with it is higher than that of base concrete. No differences of compressive strength between compacting methods are found.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2018.11a
• /
• pp.173-174
• /
• 2018

온난화 현상으로 북극 해빙 속도가 가속화되면서 북극 운항 선박이 증가하고 있어 선박의 안전 항해를 위한 기술개발이 요구되고 있다. 본 연구에서는 선박해양플랜트연구소에서 개발 중인 KRISO Arctic Safe Routing System(KARS)의 안전 최적항로 계획 방법의 선박실 운항 추진성능 모델 과 선박 고유의 빙 저항 추진 성능 데이터베이스 구성 내용을 소개하였다. 추진성능 모델은 예인 수조시험의 속도-마력 -RPM 성능 데이터와 실 운항에서 조우할 수 있는 바람, 파도 등의 외란에 기인하는 부가저항 및 빙해수조 결과를 바탕으로 다양한 빙상환경에 따른 빙 성능 추정결과를 활용하여 ISO15016: 2002 기반으로 Calm sea 및 빙 해역에서의 선박 속도-마력 성능에서 외란에 의한 부가저항에 따른 소요마력 및 속도변화를 추정하도록 하였다. 제안된 성능모델은 최적 북극항로 탐색 모듈과 결합되어 안전한 북극항로를 도출할 수 있음을 확인하였다.

• Journal of Korean Association for Spatial Structures
• /
• v.7 no.4
• /
• pp.89-96
• /
• 2007

The fundamental frequency maximization of beam structures is carried out by using strain energy based topology optimization technique. It mainly uses the modal strain energy distributions induced by the mode shapes of the structures. The modal strain energy to be minimized is employed as the objective function and the initial volume of structures is adopted as the constraint function. The resizing algorithm devised from the optimality criteria method is used to update the hole size of the cell existing in each finite element. The beams with three different boundary conditions are used to investigate the optimum topologies against natural mode shapes. From numerical test, it is found to be that the optimum topologies of the beams produced by the adopted technique have hugh increases in some values of natural frequencies and especially the technique is very effective to maximize the fundamental frequency of the structures.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.13 no.4
• /
• pp.209-214
• /
• 2013

If a human is taken with a disease, the electric resistance of the diseased part is higher than the surrounding area. The inherent current of the human body does not flow well in the diseased part due to high electric resistance. In this paper, we simulated the process to calculate the exact time of electronic acupuncture suitable for patient's physical condition using fuzzy logic and inference. Moreover, In this paper, It utilizes fuzzy logic and fuzzy inference rule to estimate the proper treatment duration for each patient. Physical condition, related disease, and age effects are studied for electronic acupuncture.

• Electrical & Electronic Materials
• /
• v.10 no.8
• /
• pp.756-762
• /
• 1997

In this paper the change of electrical properties of transformer oil due to electron beam irradiation is investigated. The specimens are produced with a some different dose of 0.5[Mrad], 1[Mrad] and 2[Mard] except for original specimen. The physical properties of each specimen is analyzed by using the FT-IR spectrum. So it is confirmed that carbonyl groups are increased according to the increase of electron beam dose and also that the nitric compounds are disappeared. The magnitude of dielectric dissipation factor appears maximum value by the contribution of dipoles and ions in the low temperature low voltage region and it is stable due to the saturation of carriers in the high temperature high voltage region in the electric conduction characteristics. Volume resistivity is also measured one of original specimen is larger than irradiated specimen.

• Journal of the Korea Institute of Building Construction
• /
• v.15 no.2
• /
• pp.153-160
• /
• 2015

The marble powder is a by-product that can be freely collected during the manufacturing process of marble, such as sawing, shaping, and polishing. Disposal of this waste powder is one of the environmental problems worldwide today. Therefore, this study investigated to solve this problem by consuming the waste marble powder in high fluidity concrete, as a pore filler. For this purpose, the waste marble powder was used as a binder replacing 5%, 10%, 15%, and 20% of cement in high fluidity concrete. After mixing, slump flow test, time-to-reach the slump flow of 500mm test, O-lot test and U-box test were conducted with fresh concrete. For the hardened concrete, compressive strength was determined at the age of 28 days. According to the test results, the workability of high fluidity concrete increased with the powder of 15% replacement, and the compressive strength of high fluidity concrete also increased with the same amount of powder.

• Journal of Korea Water Resources Association
• /
• v.52 no.4
• /
• pp.255-264
• /
• 2019

The trapezoidal ribs had been installed in the retaining wall in order to reduce to flood damage in the impingement of mountain rivers. In this study, experiments in open channel with the trapezoidal ribs on sidewall were conducted to evaluate the effect of flow resistance by the trapezoidal shape. The hydraulic flow characteristics according to the flow rates were surveyed where the wall roughness is k-type that dimensionless spacings, ${\lambda}_{nv}$, are 6, 9, and 12. The flow-resistance factors such as roughness and friction coefficients increased generally with increase of the spacing of ribs. In high flow rate the friction coefficient showed the maximum value when ${\lambda}_{nv}$ is 9. Though the trapezoidal ribs has the relatively smaller flow resistance compared to the square ribs, their form drag accounted for mean 62% of the total flow resistance. It was confirmed that the optimal spacing of trapezoidal ribs to maximize the effect of flow resistance as the wall roughness increases are 9 to 12 times of the height of trapezoidal ribs.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.8
• /
• pp.25-31
• /
• 2018

Recently, research on the development of lightweight vehicle bodies is increasing continuously as a response to fuel economy regulations. To reduce the weight of a vehicle body, a conventional steel plate has been substituted by light weight material with high specific strength and the jointing of multi-materials is generally applied. On the other hand, the customer's demand for safety and emotional quality in NVH (Noise, Vibration and Harshness) is becoming increasingly important. Therefore, a light weight with proper strength and NVH quality is needed. In the view of light weighting and NVH quality, the application of a vibration proof steel plate can be an effective solution but the formability of a sandwich panel is different with a conventional steel sheet. Therefore, careful analysis of formability is required. This study aims to characterize the formability of a sandwich high-strength steel plate. The high-strength steel plates of different thicknesses with resistance spot welding and sealer bonding were analyzed using forming limits diagram through a cup drawing test.