• Magazine of the Korea Concrete Institute
• /
• v.5 no.2
• /
• pp.162-170
• /
• 1993

축력과 횡력을 받는 전단벽의 휨과 전단 거동을 분리산정하기 위하여 R/C 전단벽에 관한 실험 결과에 대해 System Identification을 행한다. 이를 토대로, 전단벽의 강도 저하 계수 'R'과 극한 회전능력을 구하는 실험식을 제안한다. R/C뼈대구조-전단벽에 대한 비탄성 해석 유한요소 컴퓨터 프로그램(IDARC)을 이용하여 전단벽의 지진 이력 거동을 재현한다. Identification 결과를 Digitize한 실험 결과와의 비교에 의해 검증하고, 총변형으로부터 휨과 전단에 의한 변형요소를 해석적으로 분리 함으로서 비탄성 전단 거동과 강도 저하 계수 'R'의 산정이 가능해진다. 또한 실험 결과에 대한 회귀 분석을 통하여 전단벽의 극한 회전 능력에 대한 실험식이 얻어진다.

• Journal of the Korea Concrete Institute
• /
• v.18 no.1 s.91
• /
• pp.109-116
• /
• 2006

An incremental approach to predict the time dependent flexural behavior of composite girder is presented in the framework of incremental finite element method. Age dependent nature of creep, shrinkage, and maturing of elastic modulus of concrete is prescribed in the incremental tangent description of constitutive relation derived based on the first order Taylor series expansion applying to the total from of stress-strain relation. The loop phenomenon in which age dependent nature of concrete causes stress redistribution and it causes creep in turn is taken into account in the formulation through the incremental representation of constitutive relation. The developed algorithm predicts the time dependent deflections of 4.8m long two span double composite box girder subjected to shrinkage, maturing of elastic modulus, and creep initially induced by self weight. Comparison shows a good agreement between the predicted and measured results.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.49 no.3
• /
• pp.227-231
• /
• 2004

A total of 219 polymerase chain reaction tests of genetically modified (GM) DNA sequences in soybean seeds and soybean sprouts were conducted during 2000-2001. No CM gene was found in 96 tests of soybean seeds. However, either a functional CP4EPSPS gene or the 355 promoter gene was found three times in 2000 and eight times in 2001, in between 0.01 and 0.17％ of soybean spout products, in 123 tests. Since the amount of GM genes was much less than the threshold limit of 3％, none of the 11 positive soybean-sprout samples needed to be libeled GM crops. Of these, seven sprout samples were from domestic seeds and four were from seeds imported from China. To find the contamination route, the raw materials, seed surface, floor of the storage room, area around the selection machine, surface of the packaging film and corn powder used in the package were tested. The 35S promoter gene was detected in only two samples of the corn powder (0.1％). Although we could not find the cause of the GM contamination, the sprout package film is one possibility. In total,8.9％ of the soybean sprout tests were GM positive, but the amounts were much less than the threshold of 3％. This means that there are frequent false-positives and these would threaten the sprout industry if GMO were decided qualitatively. Food companies should make their safety data available to the public and make an effort to address people's concerns about GM food more openly. In addition, there is a need to establish a quantitative test for GM genes in sampled water and a sampling method for raw materials.

• Food Science and Industry
• /
• v.52 no.2
• /
• pp.153-170
• /
• 2019

With the breathtaking stride beingmade in the field of biotechnology, biocatalyst research using genetically modified microorganism (GMM) is actively being pursued in food industry. However, domestic food and food additive regulation standards and the number of examination management examples currently used in industry is lacking significantly. Up till now, there are only 6 examples of domestic GMM examination and approval cases for food production purposes and furthermore they are limited to the production of functional sweeteners. Domestically, although GMM is developed as a processing aid (contained use), if they are used in the production of food, the safety of GMM, including environmental safety, is evaluated. Also the produced food or food additives using GMM need to be separately examined and approved as a novel food. On the other hand, imported products produced using GMM need to gain approval for the final product only. Thus the expense and the time to obtain regulatory approval is advantageous for imported products versus domestically produced products. This commentary is written to create the opportunity to reform the current domestic food GMM regulation by comparing and discussing domestic and foreign case analyses of safety evaluation of GMM and related regulations.

• Journal of the Korea Concrete Institute
• /
• v.15 no.1
• /
• pp.69-77
• /
• 2003

One directional and biaxial tension tests of 13 reinforced concrete panels were conducted to derive a constitutive law of concrete. Based on the test results, a model equation is derived for the stress-strain relationship of concrete in tension. Main test variables are reinforcement ratio and the load ratio applied in two directions. In addition a failure envelope of concrete in tension-tension region is suggested based on the initial crack occurrence. Test results show that the concrete carries substantial tensile stress even after cracking occurrence. However, the application of this proposed stress-strain relationship for concrete is limited to the case where the direction of reinforcement coincides with the direction of the applied principal stresses.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.8 no.2
• /
• pp.195-204
• /
• 2004

A series of constant creep and repeated creep tests are performed to investigate the behavior of visco-elasto-plastic materials of chemical grouted sands. In the result of constant creep test, the material exhibits three types of shear strain : elastic, plastic, viscoelastic. The elastic, plastic and viscoelastic strains are linear, i.e., the strains are proportional to the stresses for loading. Good agreement is found between the predicted viscoelastic and test results by the power law and the generalized model. In the repeated creep test, the instantaneous recoverable strain is time-independent and the magnitude of accumulated plastic strain increases with number of cycles. Also it is seen that the accumulated plastic strains are approximately proportional to stress. There are no significant differences between test results predicted values for first cycle, and the differences increase relatively insignificantly with number of cycles.

• International Journal of Highway Engineering
• /
• v.6 no.4 s.22
• /
• pp.65-73
• /
• 2004

Marshall stability and flow don't reflect mechanical property of asphalt mixtures and have little correlation with rutting-related performance. There is often rutting occurred on the asphalt pavement which was constructed using a mixture passing the specification for stability and flow. This study dealt with comparison of volumetric properties of mixtures from Marshall mix design and from Superpave mix design. This study used one binder, three aggregates and two gradations. The mixtures were manufactured by each mix design method. Result showed that OAC, VMA and VFA by Marshall mix design were higher than those by Superpave mix design. This is because Mashall mixture has the gradation prone to rutting and it should be further investigated whether or not the high OAC is direct cause of rutting in asphalt pavement.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.117-120
• /
• 2008

The bridge bearings are devices absorbing the displacements of the superstructure. KS F 4420 relative to the design of elastomeric bearings in Korea allows shear deformation up to 70% of total rubber height. For the elastomeric bearings to fulfill their shear function required in the design, the stability of allowable shear strain of elastomeric bearings relative to the shear failure should be guaranteed. Moreover considering the possibility that elastomeric bearings are applied to the seismic design together with isolation devices, elastomeric bearings is supposed to display higher shear performance. In this paper ultimate shear performance tests were performed. The measured ultimate shear strains were over 200%. Therefore an allowable shear strain provision becomes safe. But elastomeric bearings expected to show their performance in one united body reveled the separation of components near 200% shear strain. These separation in elastomeric bearing can cause unexpected impact or concentrated stress to bridge system considering to application of seismic design. Therefore provision relevant to separation problem is necessary.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.2 no.2
• /
• pp.152-157
• /
• 2014

The objective of this study is to examine the drying shinkage and autogenuous shrinkage strains of heavyweight magnetite concrete. As a main parameters, cement was partially replaced by fly ash (FA) from 5% to 35%. The measured shrinkage strains were compared with predictions obtained from CEB-FIP equations and Yang et al.'s model. Test results showed that the magnitite of the autogenous and total shrinkage strains of heavyweight concrete slightly increased as the amount of fly ash increases up to 15%, beyond which the strains tended to decrease. The CEB-FIP equations considerably underestimated the shrinkage behavior of heavyweight concrete, indicating that this trend was more notable with the age. On the other hand, Yang et al.'s model predicted accurately the shrinkage of heavyweight concrete.

• Journal of the Korea Concrete Institute
• /
• v.13 no.2
• /
• pp.130-138
• /
• 2001

This paper presents on the shear behavior prediction of reinforced concrete beams using Transformation Angle Truss Model (TATM). The TATM can evaluate the stress-strain relationships for cracked concrete by transforming stresses and strains for principal plane into those over the crack surfaces. This proposed analytical method simplifies the Fixed Angle Softened Truss Model (FA-STM) and removes the limitation of applicability of the FA-STM. The shear.strength and strain of reinforced concrete beams are predicted by using the TATM. For the verification of proposed method, experimental results of reinforced concrete beams were compared with theoretical results by the TATM, FA-STM and Rotating Angle Softened Truss Model (RA-STM).