• Clean Technology
• /
• v.20 no.4
• /
• pp.425-432
• /
• 2014

The effect of two important parameters of a catalytic membrane reactor (CMR), hydrogen selectivity and hydrogen permeance, coupled with an Ar sweep flow and an operating pressure on the performance of a water gas shift reaction in a CMR has been extensively studied using a one-dimensional reactor model and reaction kinetics. As an alternative pre-combustion $CO_2$ capture method, the feasibility of capturing a pressurized and concentrated $CO_2$ in a retentate (a shell side of a CMR) and separating a purified $H_2$ in a permeate (a tube side of a CMR) simultaneously in a CMR was examined and a guideline for a hydrogen permeance, a hydrogen selectivity, an Ar sweep flow rate, and an operating pressure to achieve a simultaneous capture of a concentrate $CO_2$ in a retentate and production of a purified $H_2$ in a permeate is presented. For example, with an operating pressure of 8 atm and Ar sweep gas for rate of $6.7{\times}10^{-4}mols^{-1}$, a concentrated $CO_2$ in a retentate (~90%) and a purified $H_2$ in a permeate (~100%) was simultaneously obtained in a CMR fitted with a membrane with hydrogen permeance of $1{\times}10^{-8}molm^{-2}s^{-1}Pa^{-1}$ and a hydrogen selectivity of 10000.

• Journal of the korean Society of Automotive Engineers
• /
• v.6 no.2
• /
• pp.14-19
• /
• 1984

종래에 많이 사용된 각양의 계측 방법을 일일이 설명하는 것은 본 해설의 목적이 아니기 때문에 개략적으로 분류하여 설명하면 다음과 같다. 1) 시간 평균유속은 주로 프로브(probe)를 경유하여 동압과 정압의 측정에 의하여 수행되어 왔다. 연소반응이 있으면 밀도의 변화가 있게 되는데 밀도는 후술하는 농도의 계측과 온도의 계측에 의하여 정해져 동압과 정압으로부터 유속으로 변환된다. 시간분해능이 높은 비접촉식(직접 프 로브를 측정부에 삽입하지 않는 방법) 유속측정이 가능한 방법으로는 레이저 도플러 유속계 (Laser Doppler Velocimetry, 이하 LDV로 표현)를 들 수 있다. LDV는 압력측정에 의한 유속 산출법에서와 같은 온도 및 농도 등의 부수적인 계측이 필요없이, 직접 유속을 검출할 수 있으며 또한 검정이 필요없는 절대유속 측정이 가능하며 현재 연소반응이 있는 흐름에 대한 대부분의 연구에 적용되고 있는 실정이다. 2) 시간평균 화학종 농도측정에 가장 많이 쓰이는 방법은, 연소가스를 채취하여 가스 크로마토 그라프(Gas Chromatograph)로 분석하는 것을 들 수 있다. 한편, 시간 분해능이 높은 화학종 농 도의 계측은 레이저를 사용하여 각 화학종의 발광, 산란 및 흡수성을 이용, 측정한다. 3) 온도측정은 대부분 열전대를 사용하고 있다. 그러나 이 방법은 직접 프로브를 삽입해야 하므로 사용한계의 범위가 지극히 좁으며, 연소반응이 일어나므로 프로브 자체의 촉매반응 및 복사 열전달에 의한 보정 등이 사용상 큰 문제로 제기된다. 그러나 최근 레이저 이용기술의 발달로 (2)항에서의 농도 계측과 같이 반응기체의 온도 및 성분의 동시측정이 가능한 방법도 점차 현 실화 되어가고 있다. 그 대표적인 예로 CARS법(Coherent Anti-Stokes Raman Spectroscopy)을 들 수 있다. 이상으로부터 연소반응이 일어나는 흐름에서의 각종 계측에서는, 비접촉 측정의 가능성과 시간 공간 분해능의 특징으로 미루어 앞으로는 레이저를 이용한 계측 방법이 그 주류를 이룰 것으로 사료된다. 우선 본 해설은 기체의 온도 및 농도의 광학적 측정방법중 Raman산란광 검출법에 대하여 실제로 측정하는 입장에서 간단히 소개한다.

• Journal of the Korean Chemical Society
• /
• v.30 no.1
• /
• pp.118-125
• /
• 1986

A small scale combustion unit was built to evaluate the CO suppression effects by various chemical additives added to coal briquettes. Among the additives tested comprising various transition metal compounds with catalytic activities, natural minerals and oxidizing agents, the copper component has shown the best CO suppression effect, and in particular, copper oxide dispersed on porous supports such as ${\gamma}-Al_2O_3$ was most effective. For instance, 0.5% of copper added to coal briquettes in this way bas exhibited 1.4 % CO in the combustion gas at the ignition and beginning stage of combustion and 0.3 % CO at the final stage. The effects of calcium compounds on the fixation of sulfur in coal were also evaluated to reduce the contents of sulfur compounds in the combustion gases.

• Journal of the Korean Institute of Gas
• /
• v.15 no.2
• /
• pp.15-20
• /
• 2011

Although CNG is able to meet the current emission standards, it is expected to be impossible to satisfy the requirements of the next EURO-6 emission regulation without an additional after-treatment device. Hydrogen is known to be a gaseous fuel which features the wide flammability limit and the fast reactivity. A certain amount of hydrogen addition to CNG is able to extend the lean combustion range and produce lesser amounts of harmful emissions. In this research, the combustion and emission characteristics of HCNG(mixture of Hydrogen and CNG) fuel were experimented in an 11-liter heavy duty lean burn engine varying hydrogen contents, air-to-fuel ratio and spark timing. The optimization of this HCNG engine for a city bus was performed through the evaluations of oxidation catalyst characteristics.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.3
• /
• pp.343-350
• /
• 2012

A planar solid oxide fuel cell (PSOFC) is studied in its application in a high-temperature stationary power plant. Even though PSOFCs with external reformers are designed for application from the distributed power source to the central power plant, such PSOFCs may sacrifice more system efficiency than internally reformed SOFCs. In this study, modeling of the PSOFC with an external reformer was developed to analyze the feasibility of thermal energy utilization for the external reformer. The PSOFC system model includes the stack, reformer, burner, heat exchanger, blower, pump, PID controller, 3-way valve, reactor, mixer, and steam separator. The model was developed under the Matlab/Simulink environment with Thermolib$^{(R)}$ modules. The model was used to study the system performance according to its configuration. Three configurations of the SOFC system were selected for the comparison of the system performance. The system configuration considered the cathode recirculation, thermal sources for the external reformer, heat-up of operating gases, and condensate anode off-gas for the enhancement of the fuel concentration. The simulation results show that the magnitude of the electric efficiency of the PSOFC system for Case 2 is 12.13% higher than that for Case 1 (reference case), and the thermal efficiency of the PSOFC system for Case 3 is 76.12%, which is the highest of all the cases investigated.

• Resources Recycling
• /
• v.27 no.3
• /
• pp.93-99
• /
• 2018

Effective extraction of platinum group elements by dissolving waste platinum scrap from the display industry and solvent extraction, was studied. The extracted platinum solution was prepared as a precursor solution for diesel automotive exhaust gas purification catalyst and its catalytic activity was tested. The behavior of aqueous species of platinum was investigated through solution chemistry and based on the existence and behavior of these chemical species, the possibility of extraction and separation was established. By dissolving waste scrap by electrochemical method, the dissolution time of scrap was shortened and the extraction efficiency was increased. Through separation and removal of rhodium component, solvent extraction by TBP, and stripping by hydrochloric acid, Pt-Chloride-$H_2O$ solution was prepared. And then, an platinum amine complex solution through amination reaction with this solution as a raw material was prepared. The possibility of producing high-value platinum compounds from platinum group waste scrap was investigated by preparing platinum amine complex solution and then examining the catalytic activity with this amine precursor on the combustion reaction of carbon black.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.130.2-130.2
• /
• 2010

한전 전력연구원에서는 2009년 12월부터 125 kW급 용융탄산염 연료전지 발전시스템의 성능평가를 위한 운전이 진행되고 있다. 현재 진행 중인 "250 kW급 열병합 용융탄산염 연료전지 Proto Type개발" 과제의 최종시작품인 250 kW급 발전시스템은 125 kW급 MCFC 스택 2기로 설계되어, 125 kW급 시스템의 시험운전은 매우 중요한 기술적 성과가 될 것이다. 현재 125 kW급 MCFC 스택은 10,000 $cm^2$의 유효전극면적을 갖는 단위전지들로 구성되었으며, 적층 스택의 온도 및 농도분포의 최적화를 위해 내부 매니폴드 및 Co-flow Type 열교환기 기반의 분리판을 개발 적용하였다. 연료극의 전극 구성은 Ni-Al alloy로, 공기극의 전극 구성은 Lithiated-NiO로 이루어졌다. 그리고 매트릭스는 ${\alpha}-LiAlO_2$로 제작되었고, 전해질은 Li과 K Carbonate가 68 : 32 비율로 섞인 용융염을 사용하였다. 본 125 kW급 용융탄산염 연료전지 시스템의 운전평가는 고적층 스택의 온도 및 농도 분포를 확인하고, 최적화된 스택 운전 조건을 도출하는 것을 그 목적으로 하고 있다. 125kW급 스택 1기의 규모의 주변기기 시스템은 외부개질기, 촉매연소기, 이젝터, 고온순환 블로어 및 공기블로어 등으로 이루어져 있다. 고온형 연료전지 시스템에서 연료극과 공기극의 균일한 온도 및 압력 확보는 매우 중요하며, 이를 위하여 외부개질기 및 촉매연소기 연동을 통한 온도편차를 최소화하고, 기존 고온용 순환 블로어 대신 이젝터를 개발 도입하여 압력균형을 조절하였다. 125kW급 MCFC 시스템은 2009년 12월부터 전처리 운전을 시작하여 2010년 1월 말부터 PCS로 전기를 생산하고 있다. 평균전압 0.83V에서 100kW의 출력을 기록하였으며, 피크부하 120 kW, 누적출력량 30 MWh를 초과달성하였다.

• Transactions of the Korean hydrogen and new energy society
• /
• v.31 no.1
• /
• pp.82-88
• /
• 2020

Recently, a fuel reforming plant for supplying high purity hydrogen has been studied to increase the operation time of underwater weapon systems. Since steam reforming is an endothermic reaction, it is necessary to continuously supply heat to the reactor. A fuel reforming plant needs a methanol-O₂ catalytic burner to obtain heat and supply heat to the reformer. In this study, two types of designs of a catalytic burner are presented and the results are analyzed through the experiments. The design of the catalytic burner is divided into that the O₂ supply direction is perpendicular to the methanol flow direction (Design 1) and the same as the methanol flow direction (Design 2). In case of Design 1, backfire and flame combustion occurred in the mixing space in front of the catalyst, and in the absence of the mixing space, combustion reaction occurred only in a part of the catalyst. For above reasons, Design 1 could not increase the exhaust gas temperature to 750℃. In Design 2, no flashback and flame combustion were observed, the exhaust gas could be maintained up to 750℃. However, the O₂ distributor was exposed to high temperatures, resulting in thermal damage.

• Journal of Energy Engineering
• /
• v.2 no.2
• /
• pp.200-207
• /
• 1993

A methanol reformer was designed and fabricated using a CuO-ZnO low temperature shift catalyst, and its operation characteristics have been studied for the phosphoric acid fuel cell (PAFC) power generation system. The type of reactor was annular Methanol was consumed both for heating and for reforming fuel. Contents of carbon monoxide produced from the reformer increased as the reaction temperatures increased, but decreased as the mole ratios of water to methanol(H$_2$O/CH$_3$OH) increased. At steady state operating conditional, temperature profile of the catalytic reactor of the reformer was well coincide with the model equation, and it took 50 minutes from start to the rated condition of the reformer. When the system was operated at 4/4 and 1/4 of load, thermal efficiencies of the system were 72.3% and 77%, respectively. When the PAFC system was operated with reformed gas in the range of 62 V-37.6 V and 0-147 A, the trend of I-V curve showed a typical fuel tell characteristic. At steady state condition, the flow rates of reforming and combustion methanol were 88.1 mol/h and 50.1 mol/h, respectively.

• Journal of Sensor Science and Technology
• /
• v.3 no.3
• /
• pp.9-15
• /
• 1994

Catalytic combustible gas sensors were fabricated by using ${\gamma}-Al_{2}O_{3}$ with large surface area and noble metal catalysts. The optimum conditions for ${\gamma}-Al_{2}O_{3}$ fabrication were investigated by DT/TGA and XRD analyses and it was found that fabricated ${\gamma}-Al_{2}O_{3}$ had superior value as surface area of $215.5m^{2}/g$. Gas sensors were manufactured and tested to inflammable gases by using Pt coil as a heater and temperature sensing part, fine ${\gamma}-Al_{2}O_{3}$ powder as a bead material and Pt, Pd noble metal powder as a catalyst. From the results, fabricated sensor showed good sensitivity to LPG and LNG of 20mV/l000ppm, 6.5mV/l000ppm respectively.