• Journal of the Korean Ceramic Society
• /
• v.38 no.12
• /
• pp.1085-1092
• /
• 2001

The high efficient AC powder EL devices classified by low cost and low power consumption type fabricated using screen printing method with film thickness and organic binder. Brightness and current density were measured at frequency range of 400Hz∼1kHz and voltage range of 50∼300V$\_$rms/ to estimate optoelectrical properties of AC powder EL devices, respectively. Frequency generator was used as system producing frequency and voltage of a sine wave. Also brightness and current density were measured by luminometer and multimeter. In the case of low cost type AC powder EL device, brightness and current density were about 43 cd/m$^2$and 20$\mu$A/cm$^2$when the thickness of phosphor and dielectric layer was 45∼50$\mu$m under no addition of plasticizer respectively. In the case of low power consumption type AC powder EL device, brightness and current density were about 74 cd/m$^2$and 30∼40$\mu$A/cm$^2$when the thickness of phosphor and dielectric layer was 45∼50$\mu$m and 15∼20$\mu$m under addition of 15wt% plasticizer respectively. Also, AC powder EL device fabricated in this study showed absolutely excellent characteristics as the lifetime was longer than products of other company.

• Journal of Navigation and Port Research
• /
• v.27 no.4
• /
• pp.443-447
• /
• 2003

In this work. using 0.2 GaAs modulation doped FET(MODFET), a high performance DBS downconverter MMIC was developed for direct broadcasting satellite (DBS) application. Without LNA, the downconverter MMIC showed a very low noise of 4.8 dB, which is lower by 3 dB than conventional ones. A low LO power of -10 dBm was required for the normal DBS operation of the downconverter MMIC. which reduced the power consumption via a removal of LO amplifier on MMIC. It required only a low power consumption of 175 mW, which is lower than 70 percent of conventional ones. The LO leakage power at IF output was suppressed to a lower level than 30 dBm, which removes a bulky LO rejection filter on a board. The fabricated chip, which include a mixer, If amplifiers. LO rejection filter, and active balun, exhibited a small size of $0.84{\times}0.9\textrm{mm}^2$.

• Journal of Advanced Navigation Technology
• /
• v.17 no.6
• /
• pp.700-704
• /
• 2013

Quantum-dot cellular automata(QCA) is a new technology and it is an one of the alternative high performance over existing complementary metal-oxide semi-conductor(CMOS). QCA is nanoscale device and ultra-low power consumption compared with transistor-based technologies, and various circuits using QCA technology have been proposed. Binary-coded decimal(BCD), which represents decimal digits in binary, is mainly used in electronic circuits and Microprocessor, and it is comfortable in conversion operation but many data loss. In this paper, we present an BCD-EXCESS 3 Code converter which can be efficiently used for subtraction and half adjust. The proposed scheme has efficiently designed considering space and time complexities and minimization of noise, and it has been simulated and confirmed.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.7
• /
• pp.84-93
• /
• 2007

The pole transformer is one of the most important facility to insure the stability of electric power supply. which distributes electricity to customers directly. However there are a lot of defects which are caused by manufacturing fails(in 3 years) or deterioration (in 13 years), so we need a more improved transformer which insures quality. This thesis talks about the development of the new-type transformer using the hybrid insulation that is durable thermally, mechanically, and electrically. It would show how to lay out and produce the transformer using the hybrid insulation. And finally we are sure that we could increase the utilization rate of a transformer by 160% as compared with its own capacity through the overload test. Also, we carried out the examination about the short-circuit and insulation with a 100[kVA] model transformer, so that we expound the analysis of magnetic-mechanical forces intensity and the measure for improving short-circuit efficiency.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.1
• /
• pp.3-8
• /
• 2016

Wireless networks have evolved to the appearance of heterogeneous wireless networks(HetNet), where various networks provide data services with various data rates and coverage. One of technical issues for HetNet is efficient utilization of radio resources for system performance enhancement. For the next generation wireless networks, energy saving has become one of key performance indices, so energy-efficient resource management schemes for HetNet need to be developed. This paper addresses an energy-efficient scheduling for HetNet in order to improve the energy efficiency while maintaining similar system throughput as existing scheme, for which an energy-efficient scheduling that energy efficiency factor is included. Simulation results show that the proposed scheme achieves the reduction of energy consumption while admitting limited ragne of throughput degradation in comparison with the conventional proportional fair scheduling.

• Journal of Convergence for Information Technology
• /
• v.10 no.8
• /
• pp.7-14
• /
• 2020

In the fifth generation (5G) mobile networks, the mobile services require 100 times faster connections. One of the promising 5G technologies is non-orthogonal multiple access (NOMA). In NOMA, the users share the channel resources, so that the more users can be served simultaneously. There are several advantages offered by NOMA, such as higher spectrum efficiency and low transmission latency, compared to orthogonal multiple access (OMA), which is usually used in the fourth generation (4G) mobile networks, for example, long term evolution (LTE). In this paper, we compare the receivers for NOMA. The standard NOMA receiver, the non-SIC NOMA receiver, and the symmetric superposition coding (SC) NOMA receiver are compared. Specifically, it is shown that the performance of the standard receiver is the best, whereas the performances of the non-SIC receiver and symmetric SC receiver are dependent on the power allocation.

• Journal of Broadcast Engineering
• /
• v.10 no.4 s.29
• /
• pp.528-539
• /
• 2005

The H.264 has been adopted as the video codec for various multimedia services such as DMB and next-generation DVD because of its superior coding performance. However, the reference codec of the standard, the joint model (JM) contains quite a few algorithms which are too complex to be used for the resource-constraint embedded environment. This paper introduces very low-complexity H.264 encoding algorithm which is applicable for the embedded environment. The proposed algorithm was realized by restricting some coding tools on the basis that it should not cause too severe degradation of RD-performance and adding a few early termination and bypass conditions during the motion estimation and mode decision process. In case of encoding of 7.5fps QCIF sequence with 64kbpswith the proposed algorithm, the encoder yields worse PSNRs by 0.4 dB than the standard JM, but requires only $15\%$ of computational complexity and lowers the required memory and power consumption drastically. By porting the proposed H.264 codec into the PDA with Intel PXA255 Processor, we verified the feasibility of the H.264 based MMS(Multimedia Messaging Service) on PDA.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.1
• /
• pp.69-76
• /
• 2017

Bluetooth Low Energy (BLE), also known as Bluetooth Smart, has ultra-low power consumption; in fact, BLE-enabled devices can run on a single coin cell battery for several years. In addition, BLE can estimate the approximate distance between two devices using the Received Signal Strength Indication (RSSI) feature, enabling relatively precise navigation in indoor and small outdoor areas where GPS is not an option. In this paper, an experimental setup is presented in which BLE is used for navigation within a small outdoor area. BLE-based beacons are installed in fixed positions, which periodically transmit a universally unique identifier (UUID). A smart device receives the UUID and sends it to a database server using cellular or Wi-Fi technology. The server returns fixed position information corresponding to the received UUID codes, and the smart device uses that information to compute its current position based on relative signal strengths, and display it on a map. These results demonstrate the successful application of BLE technology for navigation in small outdoor areas. This system can be implemented for indoor navigation as well.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.47 no.1
• /
• pp.128-138
• /
• 2010

In this paper, we propose a new bit assignment scheme for Wyner-Ziv video coding. Distributed video coding (DVC) is a new video coding paradigm which enables greatly low complexity encoding because it does not have any motion prediction module at encoder. Therefore, it is very well suited for many applications such as video communication, video surveillance, extremely low power consumption video coding, and other portable applications. Theoretically, the Wyner-Ziv video coding is proved to achieve the same rate-distortion (RD) performance comparable to that of the joint video coding. However, its RD performance has much gap compared to MC-DCT-based video coding such as H.264/AVC. Moreover, Transform Domain Wyner-Ziv (TDWZ) video coding which is a kind of DVC with transform module has difficulty of exact bit assignment because the entire image is treated as a same message. In this paper, we propose a feasible bit assignment algorithm using adaptive quantization matrix selection for the TDWZ video coding. The proposed method can calculate suitable bit amount for each region using the local characteristics of image. Simulation results show that the proposed method can enhance coding performance.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.5
• /
• pp.1-9
• /
• 2016

Railroad bridges account for 25% of the entire high-speed rail network. Railway bridges are subject to gradual structural degradation or fatigue accumulation due to consistent and repeating excitation by fast moving trains. Wireless sensing technology has opened up a new avenue for bridge health monitoring owing to its low-cost, high fidelity, and multiple sensing capability. On the other hand, measuring the transient response during train passage is quite challenging that the current wireless sensor system cannot be applied due to the intrinsic time delay of the sensor network. Therefore, this paper presents a framework for monitoring such transient responses with wireless sensing systems using 1) real-time excessive vibration monitoring through ultra-low-power MEMS accelerometers, and 2) post-event time synchronization scheme. The ultra-low power accelerometer continuously monitors the vibration and trigger network when excessive vibrations are detected. The entire network of wireless smart sensors starts sensing through triggering and the post-event time synchronization is conducted to compensate for the time error on the measured responses. The results of this study highlight the potential of detecting the impact load and triggering the entire network, as well as the effectiveness of the post-event time synchronized scheme for compensating for the time error. A numerical and experimental study was carried out to validate the proposed sensing hardware and time synchronization method.