• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.37 no.3
• /
• pp.58-63
• /
• 2000

For the microwave high density devices and modules of the 3D configuration, we proposed radial stub for the ground connection. The proposed structure is analyzed by the full-wave analysis of finite element method (FEM) and characterized experimentally. The results show that the return loss is more than 15 dB and the insertion loss is less than 0.5 dB in the frequency range from 2.5 GHz to 6.3 GHz. The proposed grounding scheme will be useful for the ground connection lot the microwave high density devices and module of 3D configuration.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.4 no.1
• /
• pp.67-76
• /
• 2000

In this paper, a low noise amplifier has been developed, which is operating at L-band i.e., 1525-1575 MHz. By using resistive decoupling circuits, the resistor dissipates undesired signal in low frequency band. By adopting this design method the stability of the LNA is increased and the input impedance matching is improved. The LNA consists of the low noise GaAs FET ATF-10136 and the internally matched VNA-25. The low LNA is fabricated by both the RP circuit and the self-bias circuits in an aluminum housing. As a result, the characteristics of the LNA implemented show more than 32 dB in gain, lower than 0.5 dB in noise figure, 18.6 dBm output gain in 1 dB gain compression point.

• 전자공학회논문지 IE
• /
• v.45 no.1
• /
• pp.7-14
• /
• 2008

In this paper, a new high resolution XGA-SLM is implemented through modification of a commercial TFT-LCD beam projector and its optical modulation characteristics as a spatial light modulator(SLM) is also analyzed. That is, the optics module, projection lamp and fans are removed from a commercial beam projector and instead, some electric circuits to compensate their removal are manufactured and then, by inserting them into the beam projector, a new XGA-SLM is finally implemented. From some characteristic experimental results of the implemented high resolution TFT-LCD SLM, the proposed TFT-SLM is found to have an good optical linearity in amplitude and phase modulation characteristics as a function of the input gray levels. Especially, through implementation of the suggested TFT-LCD panel, the implemented SLM is proposed as a new relatively low-cost and high resolution SLM for optical information processing.

• 한국방재학회:학술대회논문집
• /
• 2011.02a
• /
• pp.166-166
• /
• 2011

한국건설기술연구원내에 세계 최초로 UHPC(초고성능 콘크리트)를 활용한 보도사장교를 설계 및 시공하여 공용중이다. 초고성능 콘크리트(UHPC, Ultra High Performance Concrete)는 기존의 콘크리트의 단점을 극복하기 위하여 강섬유 및 혼화재료를 사용하여 고강도화와 더불어 인장강도, 휨강도, 균열에 대한 저항성, 전단강도 및 내충격성을 대폭 개선시켜서 구조부재의 연성 및 강도를 확보하기 위해 개발된 것으로서 한국건설기술연구원이 독자적 연구를 바탕으로 UHPC를 개발하였고, KICT-UHPC의 특성을 충분히 반영한 보도사장교를 한국건설기술원내에 실구조물로 시공하였다. 한국건설기술연구원내 본관 1, 2동 연결 보도사장교(SUPER BRIDGE 1)의 진동실험을 통해 UHPC 보도사장교의 동특성(고유진동수 및 모드형상)을 평가하였다. 대상교량에는 보도사장교의 캔틸레버 구조 특성에 의해 발생하는 진동을 제어하기 위한 질량 264kg의 난간형 수직진동제어장치(TMD) 4대가 설치되어 있으며, 부가질량의 운동을 기계적으로 구속하거나 구속을 해제하여 TMD의 작동을 켜거나 끌 수 있도록 되어있다. TMD의 가동 및 정지시 동특성을 비교하는 정밀한 검증 실험을 통하여 TMD 설치에 의한 동특성의 변화도 평가하였다. 가진망치에 의한 충격실험으로부터 획득한 가속도 시간이력 데이터와 가진망치의 가진력 시간이력 데이터를 사용하여 주파수응답함수(FRF, frequency response function)를 계산하고, 이로부터 Super Bridge I의 동적모드형상과 고유진동수를 추출하였다. 1차 모드의 고유진동수는 TMD 정지시 2.2949 Hz, TMD 작동시 2.0996 Hz로서 8%정도 감소하였다. 충격해머에 의한 가진 실험을 통해 세계 최초로 시공한 UHPC 보도사장교의 진동특성과 관련한 신뢰성 있는 자료를 확보할 수 있었다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.7
• /
• pp.739-744
• /
• 2012

The genetic algorithm (GA) is regarded as one of the best ways for determining a global solution. Because it does not require calculating the design sensitivity differently from the ordinary gradient-based method, it is appropriate for the design problem in the ultra-high frequency range; the ordinary gradient-based method has difficulty in calculating the sensitivity in this range. This paper deals with nano-aperture grating topology optimization based on the GA and the ON/OFF method. The objective of this study is to maximize the transmittance in the measuring area. The simulation and optimization processes are carried out by using the commercial package COMSOL associated with Matlab programming. The final optimal design gives around 21% performance improvement, compared with the initial model.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.4 s.107
• /
• pp.351-357
• /
• 2006

In this paper, a direct $TM_{01}-TE_{11}$ mode converter of circular waveguide which is used the approximated design method of mode conversion between $TM_{01}$ and $TE_{11}$ modes is designed for radiation with the maximum directivity of high power energy into air (rom high power microwave antenna system. The proposed direct $TM_{01}-TE_{11}$ mode converter is calculated and designed with an approximated method for non-linear function about an extended non-constant serpentine type of circular waveguide. Then, the designed mode converter is optimized by length of 200 mm and efficiency above 95% by FIM simulation and achieved short length and high efficiency of the antenna by results of fabricated and measured characteristics.

• Geophysics and Geophysical Exploration
• /
• v.25 no.3
• /
• pp.109-119
• /
• 2022

The computational efficiency of reverse time migration (RTM) based on numerical modeling is not secured due to the high-frequency band of several hundred Hz or higher for data acquired through a three-dimensional (3D) ultra-high-resolution (UHR) seismic survey. Therefore, this study develops an RTM program to derive high-quality 3D geological structures using UHR seismic data. In the traditional 3D RTM program, an excitation amplitude technique that stores only the maximum amplitude of the source wavefield and a domain-limiting technique that minimizes the modeling area where the source and receivers are located were used to significantly reduce memory usage and calculation time. The program developed through this study successfully derived a 3D migration image with a horizontal grid size of 1 m for the 3D UHR seismic survey data obtained from the Korea Institute of Geoscience and Mineral Resources in 2019, and geological analysis was conducted.

• Journal of Broadcast Engineering
• /
• v.15 no.4
• /
• pp.527-539
• /
• 2010

Most video coding systems use YCbCr color space for their inputs, but RGB space is more preferred in the field of high fidelity video because the compression gain from YCbCr becomes disappeared in the high quality operation region. In order to improve the coding performance of RGB video signal, this paper presents an adaptive frequency-selective weighted prediction algorithm. Based on the sign agreement and the strength of frequency-domain correlation of residual color planes, the proposed scheme adaptively selects the frequency elements as well as the corresponding prediction weights for better utilization of inter-plane correlation of RGB signal. Experimental results showed that the proposed algorithm improves the coding gain of around 13% bitrate reduction, on average, compared to the common mode of 4:4:4 video coding in the state-of-the-art video compression standard, H.264/AVC.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.1
• /
• pp.25-33
• /
• 1998

In this paper, we describe a single-gate MESFET mixer at PCS(Personal Communication Service) frequency band. The PCS frequency band is 1965~2025 MHz in FR and 140 MHz in IF irrespectly. The design of the mixer was executed by microwave simulator, EEsof Libra. The matching network is consisted of rectangular inductor, MIM capacitor and open stub. The ma- nufacture work was accomplished by the micro-pen and wedge-bonder. The mixer showed $6.69\pm0.65$ dB of conversion gain, $-14.9\pm3.5$dB of RF reflection coefficient and 57.83 dB of LO/IF isolation at 10 dBm of LO power when LO frequency is 1855 MHz. When this mixer is used at PCS terminal, IF-amplifier which compensates the conversion loss of diode mixer may be omitted.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.11
• /
• pp.635-639
• /
• 2016

In the devices used in the microwave frequency band, the gain decreases as the frequency increases due to the parasitic component. To compensate for these characteristics, a linear gain equalizer with an opposite slope is needed in wideband systems, such as those used for electronic warfare. In this study, a linear gain equalizer that can be used in the 18 ~ 40GHz band is designed and fabricated. Circuit design and momentum design (optimizations) were carried out to reduce the errors between design and manufacturing. A thin film process is used to minimize the parasitic components within the implementation frequency band. A sheet resistance of 100 ohm/square was employed to minimize the wavelength variation due to the length of the thin film resistor. This linear gain equalizer is a structure that combines a quarter wavelength-resonator on a series microstrip line with a resistor. All three 1/4 wavelength short resonators were used. The fabricated linear gain equalizer has a loss of more than -5dB at 40GHz and a 6dB slope in the 18 ~ 40GHz band. By using the manufactured gain equalizer in a multi-stage connected device such as an electronic warfare receiver, the gain flatness degradation with increasing frequency can be reduced.