• Journal of Surface Science and Engineering
• /
• v.44 no.3
• /
• pp.89-94
• /
• 2011

In this study, the photocurrent characteristics of plasma sprayed $TiO_2$ coatings have been investigated according to additive transition metal (Fe, Mn, Nb powder) and heat treatment conditions. The plasma sprayed $TiO_2$ coatings by heat treatment at $400^{\circ}C$ and 90 min had the higher photocurrent at ultraviolet light, no photocurrent at visible light. The photocurrent of plasma sprayed $TiO_2$ coatings added by Fe, Mn, Nb (named by plasma sprayed $TiO_2$ composite coatings) was lower than that of plasma sprayed $TiO_2$ coatings at ultraviolet light, as was low in intensity ratio of XRD(101)/(110). and the atomic percentage of oxygen by plasma sprayed $TiO_2$ composite coatings was higher than that by plasma sprayed $TiO_2$ coatings. The photocurrent of plasma sprayed $TiO_2$ composite coatings in heat treatment at $400^{\circ}C$ and 90 min was higher than that of plasma sprayed $TiO_2$ coatings in same heat treatment conditions at ultraviolet and visible light, as was high in oxygen affinity by heat treatment.

• Resources Recycling
• /
• v.13 no.4
• /
• pp.32-38
• /
• 2004

Recently, Orimulsion (a bitumen-in emulsion) has received increasing attention as an alternative fuel. Orimulsion combusion produces an ash rich in V, Ni and Mg which are processed to recover metals. As a basic study to recover V from Orimulsion ash, physico-chemcial properties and leaching behaviours were investigated. Orimulsion ash was fine size grains ($d_{50}$ 5.9 $\mu\textrm{m}$) with 16% V, 4 % Ni and 9% S. Vanadium was easily leached in water because Orimulsion ash was mainly constituted of metal sulfates. However, the increase of leaching temperature decreased the extraction percentage of vanadium because of hydrolysis of V(V) to vanadium pentoxide. The addition of sulfuric acid could increase the leaching percentage vanadium. In case of alkaline leaching for selective recovery of vanadium, the oxidzing agent such as $H_2$$O_2$ is required to improve the leaching per-centage

• Resources Recycling
• /
• v.20 no.4
• /
• pp.52-57
• /
• 2011

Present paper reports a new method to separate the electrolyte membranes and carbon paper without using ultrasonic waves and stirring. In this method, these were separated from fuel cell membrane-electrode assembly(MEA) using the distilled water, butanol and surfactant by dipping method without the dispersion of catalyst particles. Separated carbon paper catalysts and fuel cell Pt/C catalysts were heated in aqua regia at $80{\sim}85^{\circ}C$ and added to precipitant. After calcination, Pt metal was recovered which might be used in fabricating new fuel cells.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.29 no.5
• /
• pp.893-899
• /
• 2000

To measure antioxidative activities, the various extracts from Ulmus devidiana were examined in oil emulsion. Water, ethanol, methanol and butanol were used as extract solutions. The activity oxygen species ($H_2O_2,-OH,\;KO_2$) bound the extracts for antioxidative activities were excellent. The extracts bound $Fe^{2+}$ ion and $Cu^{2+}$ ion showed effective antioxidative activities and strong chelating effects. The concentration of $Fe^{2+}$ ion and total ion in ethanol and methanol extracts from Ulmus devidiana root parts (Chinese) were higher than those of the other products. The highest superoxide dismutase-like activities showed butanol extracts from Ulmus devidiana root parts (Chinese) and water extracts from Ulmus devidiana bark parts (Korean). Electron donating abilities and nitric scavenging abilities of ethanol, methanol and butanol extracts were higher than those of water extracts. The nitrite scavenging abilities also reached the maximum at pH 1.2 and the minium at pH 6.0.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.210-210
• /
• 2010

ABO2 형태를 가진 delafossite 구조 산화물은 p-type 투명전도체 소재로 유명하다. Delafossite 구조가 p-type 투명전도체에 적합한 결정적인 이유는 밴드갭이 넓고 공유결합에 유리하기 때문이다. 투명전도체는 가시광선의 흡수가 없도록 band gap을 넓히는 것이 우선인데 이러한 band gap이 넓은 구조가 delafossite이다. 또한 delafossite 구조는 구조적으로 각각의 산화물 이온들이 유사 사면체 배위(pseudo-tetrahedral coordination)을 갖는다. 이러한 사면체 배위결합구조에서 산소이온은 비결합면이 없기 때문에 더욱더 공유결합성을 향상시킬 것으로 생각된다. 여기서 A는 +1가 cation, B은 +3가 cation으로 구성되어 있다. A자리에는 1가 원소인 팔라듐, 플래티늄, 은, 구리 등을 가질 수 있고. B자리에 3가 원소이면서도 크기가 알루미늄보다는 크고 란타늄보다는 작은 금속이 들어갈 수 있다. Delafossite 구조는 상온에서 2종류의 polytype (상온에서 Rhombohedaral 구조와 hexagonal 구조)이 존재하며 이들은 각각 3R(Rm) 및2H (P63/mmc)의 결정 구조를 가지고 있다. CuCrO2는 일반적으로 3R결정구조를 가지는 것으로 알려져 있다. delafossite 구조는 전기적 이방성을 띄고 있는데 c-축 방향으로의 전기적 특성이 a-축 방향으로의 전기적 특성보다 약 1000배 높은 물성을 띈다고 한다. 이는 c-축 방향의 원자 위치 때문인데 CuCrO2의 경우 Cu-O-Cr-O-Cu로서 3d-2p-3d-2p-3d 궤도를 가지기 때문인 것으로 알려져 있다.[ref] 반면 c-축으로 에피성장된 박막의 경우 +3가 이온이 위치한 layer에서 hole hopping에 의해 캐리어가 전도된다고 알려져 있기도 하다. 본 연구에서는 PLD를 이용하여 c-plane 사파이어 기판위에 성장된 delafossite구조인 CuCrO2박막의 특성을 알아보았다. p-type 특성을 위하여 CuCrO2에 Ni를 첨가하였으며 그에 따른 구조적 전기적 특성을 조사하였다. 성장온도와 도핑농도를 변화시켜 특성을 연구하였다. 결정구조적 특성과 전기적 특성을 분석하려 한다.

• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.3
• /
• pp.59-62
• /
• 2019

In this study, we have developed solution-processed, F-doped In-Ga-Zn-O semiconductors and investigated their applications to thin-film transistors. In order for forming the appropriate channel layer, precursor solutions were formulated by dissolving the metal salts in the designated solvent and an additive, ammonium fluoride, was incorporated additionally as a chemical modifier. We have studied thermal and chemical contributions by a thermal annealing and an incorporation of chemical modifier, from which it was revealed that electrical performances of the thin-film transistors comprising the channel layer annealed at a low temperature can be improved significantly along with an addition of ammonium fluoride. As a result, when the 20 mol% fluorine was incorporated into the semiconductor layer, electrical characteristics were accomplished with a field-effect mobility of $1.2cm^2/V{\cdot}sec$ and an $I_{on}/_{off}$ of $7{\times}10^6$.

• Journal of Adhesion and Interface
• /
• v.20 no.3
• /
• pp.102-109
• /
• 2019

The material constitution of multi-layered thin film coated on the PET base film was analyzed using ATR FT-IR and pyro GC/MS combination. The cross section of the film was acquired by cracking the film after dipping in liquid nitrogen and was observed using optical microscope. Total thickness of the coated film was $70{\mu}m$ and three layers were observed. Since each layers were too thin to analyze directly except the surface layer, analyzable area of each layers were exposed by using a proper solvent and were investigated using ATR FT-IR and pyro GC/MS. Results shows that three layers were commonly consisted of urethane-acrylate copolymers. Also, inorganic and/or metal inclusions detected by XPS and SEM-EDAX were exhibited by nano size $SiO_2$ particles in layer(1) and aluminum flakes in layer(2).

• Journal of Applied Biological Chemistry
• /
• v.64 no.4
• /
• pp.369-374
• /
• 2021

Brown blotch disease of oyster mushrooms is caused by tolaasin and its analog peptide toxins which are produced by Pseudomonas tolaasii. Tolaasin peptides form pores in the plasma membrane and destroy the fruiting body structure of mushroom. Lysis of red blood cells, hemolysis, can be occurred by cytotoxic activity of tolaasin. The hemolytic activity of tolaasin is inhibited by metal ions, such as Zn²⁺ and Ni²⁺. When Gadolinium ion was added, a biphasic effect was observed on tolaasin-induced hemolysis, an increase in hemolysis at submillimolar concentrations and an inhibition at millimolar concentrations. The mechanism of gadolinium ion-induced inhibition of tolaasin activity may not be similar to those of the inhibitions by other metal ions. Since gadolinium ion has been reported to change a lateral pressure of lipid membrane by binding to the negative charges of membrane lipids, it may not directly work on the tolaasin channel gating, but rather decrease the stability of tolaasin channel by increasing firmness of membrane.

• Korean Journal of Materials Research
• /
• v.29 no.4
• /
• pp.241-251
• /
• 2019

There are several manufacturing techniques for developing thermionic cathodes for vacuum ultraviolet(VUV) ionizers. The triple alkaline earth metal emitters(Ca-Sr-Ba) are formulated as efficient and reliable thermo-electron sources with a great many different compositions for the ionizing devices. We prepare two basic suspensions with different compositions: calcium, strontium and barium. After evaluating the electron-emitting performance for europium, gadolinium, and yttrium-based cathodes mixed with these suspensions, we selected the yttrium for its better performance. Next, another transition metal indium and a lanthanide metal neodymium salt is introduced to two base emitters. These final composite metal emitters are coated on the tungsten filament and then activated to the oxide cathodes by an intentionally programmed calcination process under an ultra-high vacuum(${\sim}10^{-6}torr$). The performance of electron emission of the cathodes is characterized by their anode currents with respect to the addition of each element, In and Nd, and their concentration of cathodes. Compared to both the base cathodes, the electron emission performance of the cathodes containing indium and neodymium decreases. The anode current of the Nd cathode is more markedly degraded than that with In.

• Applied Chemistry for Engineering
• /
• v.32 no.4
• /
• pp.449-455
• /
• 2021

Composite materials are substances that are configured to have excellent physical properties by combining the properties of a single substance, and are in the limelight as materials that exceed the performance of metals and polymers. However, it has the disadvantages of long cycle time and high unit price, and much research is being performed to overcome these disadvantages. In this study, we developed an epoxy resin curing agent that can shorten the time required for mass production of composite materials, and tried to expand the applicability of objections by imparting flame retardancy. The epoxy resin used as a basic substance utilized two types of bisphenol F and resorcinol structure, which was further modified using 9,10-dihydro-9-oxa-10-phosphaphenantrene-10-oxide (DOPO) to impart flame retardancy. Triethylphosphate (TEP) and bis [(5-ethyl-2-methyl-1,3,2-dioxaphosphorinan-5-yl)methyl] methyl phosphonate P,P'-dioxide (FR-001) were used as additives, seven kinds of compositions were blended, thermal characteristics (gelation time, glass transition temperature) and flame retardant performance were evaluated. We successfully developed an epoxy matrix that can be applied to high pressure resin transfer molding (HP-RTM) process.