• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.3
• /
• pp.52-60
• /
• 2018

In the automobile industry, in order to increase the fuel efficiency and conform to the safety regulations, it is necessary to make the vehicles as light as possible. Therefore, it is crucial to manufacture dual phase steels, complex phases steels, MS steels, TRIP steels, and TWIP from high strength steels with a tensile strength of 700Mpa or more. In order to apply ultra-high tensile strength steel to the body, the welding process is essential. Resistance spot welding, which is advantageous in terms of its cost, is used in more than 80% of cases in body welding. It is generally accepted that ultra-high tensile strength steel has poor weldability, because its alloy element content is increased to improve its strength. In the case of the resistance spot welding of ultra-high tensile steel, it has been reported that the proper welding condition area is reduced and interfacial fracture and partial interfacial fracture occur in the weld zone. Therefore, research into the welding quality judgment that can predict the defect and quality in real time is being actively conducted. In this study, the dynamic resistance of the weld was monitored using the secondary circuit process variables detected during resistance spot welding, and the factors necessary for the determination of the welding quality were extracted from the dynamic resistance pattern. The correlations between the extracted factors and the weld quality were analyzed and a regression analysis was carried out using highly correlated pendulums. Based on this research, a regression model that can be applied to the field was proposed.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.2644-2649
• /
• 2011

The purpose of this study is to propose the modular design of hybrid lightweight carbody structures made of sandwich composites and aluminum extrusion. The sandwich composites were used for secondary structures to minimize the weight of carbody, and the aluminum extrusions were applied to primary structures to improve the stiffness of carbody and manufacturability. Key requirements were defined for the modular design of hybrid carbody, and the applied parts of sandwich composites were determined through the topology optimization analysis. Consequently, feasibility of enhancing mass saving and maintainability in modular hybrid carbody design were presented, comparing with the carbody structures made of aluminum extrusion or sandwich composites only.

• Proceedings of the KSR Conference
• /
• 2005.11a
• /
• pp.1089-1096
• /
• 2005

This study was experimental test of edgewise compression properties for aluminum(type-50XX) sandwich panel with thermal environment and surface treatment using adhesive film. There was decreasing $10\%-peel$ strength after thermal environment. Through compressive. buckling mode know to seen of properties of adhesive, sheet and core strength. First case of Chromate to aluminum sheet, know low shear strength of adhesive through buckling mode but case of Beomite to aluminum sheet, know than thin sheet and core low strength through buckling mode.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.7
• /
• pp.735-742
• /
• 2014

A self-piercing rivet (SPR) is a mechanical component for joining dissimilar material sheets such as those of aluminum alloy and steel. Unlike conventional rivets, the SPR directly pierces sheets without the need for drilling them beforehand. However, the regular SPR can undergo buckling when it pierces a high-strength steel sheet, warranting the design of a helical SPR. In this study, the joining and forging processes using the helical SPR were simulated using the commercial FEM code, DEFORM-3D. High-tensile-strength steel sheets of different strengths were joined with aluminum alloy sheets using the designed helical SPR. The simulation results were found to agree with the experimental results, validating the optimal design of a helical SPR that can pierce high-strength steel sheets.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.2
• /
• pp.98-102
• /
• 2012

Increasing the fuel economy has been an inevitable issue for the development of new cars, and one of the important measures to improve the fuel economy is to decrease the vehicle weight. In order to obtain this goal, the researches about lighter, stronger and the well impact absorbing bumper impact beam have been studied without sacrificing bumper safety. In this study, the overall weight reduction possibility of rear bumper impact beam could be examined based on the variation of frontal, offset and corner impact crash capability by substituting a ultra high strength steel material (boron steel ) having tensile strength of 1.5 GPa grade instead of conventional steels. In addition, the section variations (open section, closed section, open section with 5 stays) of the bumper impact beam structure were examined carefully. It could be reached that this analysis could be well established and be contributed for design guide and the optimum design conditions of the automotive rear bumper impact beam development.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.118-118
• /
• 2009

자동차의 경량화, 안전성 그리고 내식성 향상을 위하여 고강도 강판 및 도금 강판의 적용이 증가하면서 자동차 산업의 많은 부분에서 적용되는 저항 점용접에서도 고강도 강판과 도금강판의 적용이 증가하는 추세이다. 이에 따라 고강도 강판과 도금 강판의 낮은 용접성을 개선하기 위하여 기존의 단상 AC 용접기에서 전류 파형의 형태를 개선한 인버터 DC 용접기가 차체 조립라인에서 많이 사용되고 있다. 본 연구에서는 고강도 강판의 저항 점용접의 연속타점 시 단상 AC용접기와 인버터 DC용접기의 전극의 연속타점 수명의 차이를 비교하고 분석하기 위해 590MPa 급 전기아연도금강판을 이용하여 AWS 규격에 연속타점실험을 기준으로 단상 AC 와 인버터 DC 용접기의 연속타점 실험을 실시하였다. 연속타점실험 중에 전극의 형상관찰을 위해 100타점 간격으로 carbon paper를 이용해 전극 직경 변화를 관찰 하였으며, 100 타점간격으로 동저항을 측정하고 인장 전단 시편과 Peel test 시편을 제작하여 연속타점 시 단상 AC와 인버터 DC 용접기의 저항 점용접 연속타점 수명을 비교 분석하였다. 그리고 연속타점 실험 후 사용된 전극의 표면과 단면 형상을 각각 OM, SEM, EDX로 분석하여 전극 표면의 Zn과 합금화 된 전극의 합금층을 분석하였다. 그 결과 590MPa급 전기아연도금강판의 저항 점용점 연속타점 수명평가에서 인버터 DC 용접기가 단상 AC 용접기보다 200타점 더 우수한 연속타점 수명을 보유하였다. 특히 인장강도 기준 측면에서는 인버터 DC 용접기의 전극 연속타점수명은 매우 우수하다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.3
• /
• pp.339-344
• /
• 2013

Hot forming using boron steel is currently used for manufacturing low-weight automobile body parts, and a high tensile strength of about 1,500 MPa is obtained after hot forming. However, a high fatigue life is a more important factor than high strength when it is used for automobile suspension parts. A tubular torsion beam axle (TTBA) is one of these suspension parts, and this research deals with the fatigue characteristic of TTBA using hot forming. The low cyclic fatigue life of boron steel is investigated according to the cooling method. In addition, a structural and fatigue analysis of TTBA is performed to predict the fatigue life. The stress concentration that occurs in the tubular torsion beam is found, and the longest fatigue life occurs when rapid cooling is utilized in the TTBA fabrication.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.12
• /
• pp.1367-1372
• /
• 2014

As the awareness of the environmental crisis has recently increased around the world, numerous studies in the transport industry have been conducted to solve this problem through lightweight car bodies. The hot-stamping process has been presented as solution to achieve a light weight. Hot-stamping is a method that is used to obtain ultra-high strength steel (1,500 MPa or greater) by simultaneously forming and cooling boron steel in a press die after heating it to a temperature of $900^{\circ}C$ or above. This study involved a, fundamental examination of laser parameters to investigate the laser weldability of boron steel. As a result, the following optimum parameters for the shielding gas were found: Q = 20 l/min, ${\alpha}=40^{\circ}$, d = 20mm, and l = 0 mm. The hardness of butt weldment increasesed sharply as a result of martensite formation at the fusion zone.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.4
• /
• pp.383-391
• /
• 2011

The hot-stamping technique is used to manufacture high-strength parts by press forming by heating at a temperature above the Austenite transformation temperature and then rapid cooling. Boron steel, which contains a very small amount of boron, is one of the materials used for hot stamping. The purpose of this study is to show the microstructures and to investigate the mechanical properties under different heat-treatment conditions. The heat treatment of water quenching was conducted at the various temperatures and different elapsed times. These can be practical data useful when boron steels are used for hot stamping. Furthermore, the microstructures and mechanical properties of the spot-welded specimen with coatings and counterpart materials (SPRC 340, SPRC 590) is investigated in order to determine the welding characteristics of boron steel at different welding condition.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.2
• /
• pp.179-186
• /
• 2012

In the automobile industry, reducing the weight is the most important objective for reducing air pollution and improving the fuel efficiency. For this reason, the application of aluminum sheets is increasing. When the sheets are applied to the automobile, using inappropriate variables for the material, product design, and press processing can generate tearing, wrinkling, and spring-back problems, which are the main types of failure in the manufacturing process. Therefore, it is necessary to reduce these failures by harmonizing the many variables and strictly managing the processes. In this research, we study the theoretical plasticity instability of Al5454 and obtain the forming limit diagram (FLD) using MATLAB. Moreover, we compare the theoretical FLD with an experimental FLD obtained from a stretching test.