• Journal of the Korean Applied Science and Technology
• /
• v.33 no.1
• /
• pp.118-128
• /
• 2016

As the interest on the air-pollution is gradually rising up at home and abroad, automotive and fuel researchers have been working on the exhaust emission reduction from vehicles through a lot of approaches, which consist of new engine design, innovative after-treatment systems, using clean (eco-friendly alternative) fuels and fuel quality improvement. This research has brought forward two main issues : exhaust emission and PM (particulate matter) particle emissions of gasoline vehicle. Exhaust emission and PM particle of automotive had many problem that cause of ambient pollution, health effects. In addition, researcher studied the environment problems of the MTBE contained in the fuel as oxygenate additives. The researchers have many data about the health effects of ingestion of MTBE. However, the data support the conclusion that MTBE is a potential human carcinogen at high doses. Based on the oxygenated fuel additive types (MTBE, Bio-ETBE, Bio-ethanol, Bio-butanol), this paper discussed the influence of oxygen contents on gasoline fuel properties and evaporative emission characteristics. Also, this paper assessed the acceleration and power performance of gasoline vehicle for the fuel property.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1994.04a
• /
• pp.94-99
• /
• 1994

최근 인구의 과밀화와 이에 따른 지가의 상승 등으로 대표적인 주거용 빌딩인 아파트의 고층화가 급속하게 진행되고 있고 아파트에 설치되는 엘리베이터도 점차 대형화, 고속화 되고 있다. 실례로 15층 아파트의 경우 11인승, 60m/min의 엘리베이터가 일반적으로 사용되는 반면, 20층 아파트의 경우 17인승, 90m/min이 주로 사용된다. 이와 같이 엘리베이터의 용량과 운행 속도가 증가함에 따라 필연적으로 소음 및 진동 문제가 발생하게 된다. 특히 아파트의 경우 침실, 공부방 등 고도의 정숙을 요하는 생활 공간이 많고, 내부 공간의 활용도를 높이기 위하여 이들 방들이 엘리베이터 기계실 또는 운행 통로와 직접 접하여 있는 경우도 있어 이 경우 소음, 진동 문제는 아주 심각한 문제로 대두된다. 본 연구소가 측정한 방에 의하면 S신도시 L아파트의 경우 아파트 최상층 방에서 실내 소음도가 46dB(A), 벽의 진동가속도가 3.4mm/s$^{2}$(RMS)으로 나타났다. 진동의 경우 생활에 직접적인 악영향을 미칠 수준은 아니지만 소음의 경우 ASHRAE 권장 주택소음 기준치가 35dB(A) 이하임ㅇㄹ 감안하면 주거에 곤란한 수준이다. 수년전, 고층 아파트가 보급될 초기에는 아파트에 엘리베이터가 설치되어있다는 그 자체만으로 충분한 장점이 되어 다소음 소음, 진동문제는 큰 불만거리가 되지 않았지만 엘리베이터가 보편화된 지금에는 엘리베이터의 편리성만으로는 점점더 크게 요구되는 정숙성이 보상되지 않는다. 따라서 전반적인 아파트의 소음, 진동 문제에 큰 비중을 차지하는 엘리베이터에 의한 소음, 진동에 관하여 체계적인 연구가 필요하다. 이에 본고에서는 엘리베이터에 의한 아파트의 소음 및 진동에 관하여 그 현황, 원인 그리고 대책에 관한여 논하고자 한다.감 방법을 연구하였고, T.Sakai는 5자유도 모델을 이용하여 엔진 공회전시 발생하는 치타음에 대해 이론과 실험을 통해 해석하고, 엔진 회전수 변동, 클러치 특성, 변속기의 드래그(drag) 토크의 영향과 치타음 저감을 위한 개선된 클러치 특성을 제시하였다. 이 외에도 Thomas C.T.와 E.P.Petkus는 특정 차량에 대한 동력전달계의 비틀림 진동 현상에 대해 연구하였다. 이러한 연구들로 볼 때, 자동차 동력전달계에서 발생하는 진동은 이론과 실험을 통해 그 해석이 가능하며 설계에 매우 유용하게 이용되고 있음을 알 수 있다. 따라서, 본 연구는 4 실린더 4 싸이클 1.5 L 엔진을 장착한 경승용차의 실차 주행실험을 통해 가속 페달의 급조작에 따른 차체의 종진동 현상을 측정하고, 엔진-변속기-타이어-차체의 반환정계 4자유도 진동모델로 시뮬레이션을 수행하여 실차 주행실험의 결과치와 비교, 분석한 후 클러치 비틀림 특성을 비롯한 자동차 동력전달계의 각 설계인자들이 차체의 종진동에 어떠한 영향을 미치는가를 해석하고자 한다.be presented.LIFO, 우선 순위 방식등을 선택할 수 있도록 확장하였다. SIMPLE는 자료구조 및 프로그램이 공개되어 있으므로 프로그래머가 원하는 기능을 쉽게 추가할 수 있는 장점도 있다. 아울러 SMPLE에서 새로이 추가된 자료구조와 함수 및 설비제어 방식등을 활용하여 실제 중형급 시스템에 대한 시뮬레이션 구현과 시스템 분석의 예를 보인다._3$", chain segment, with the activation energy of carriers from the shallow trap with 0.4[eV], in he amorphous regions.의 증발산율은 우기의 기상자료를 이용하여 구한 결과 0.05 - 0.1

• Journal of Korean Society of Transportation
• /
• v.10 no.1
• /
• pp.55-62
• /
• 1992

교통수요는 교통정책 및 교통시설 계획의 수립 및 평가에 중요한 영향을 미치게 되므로 교통수요의 예측은 교통연구에서 중요한 부문을 차지하고 있다. 도로밑에 설치된 전자차량감지기(Electronic Vehicle Detector)로부터 자동 수집된 링크 교통량 자료(Traffic Counts)를 주요 입력자료로 이용하여 계획지역의 기종점 통행표(Origin Destination Trip Matrix)를 작성할 수 있는 기법 들이 최근 수년동안 많이 발달하게 되었다. 이러한 새로운 기법들은 가구조사(Home Inteview), 노변면접조사(Road-Side Interview)등을 토하여 조사된 자료를 기초로하는 전통적은 4단계 교통수요추정방법(Conventional 4-Stage Estimation Method)-통행발생(Generation), 통행분포(Distribution), 수단선택(Modal Split), 교통배분(Assignment)-과 비교하여 첫째로 정확도가 높은 링크 교통량 자료를 별도의 조사를 거치지 않고서도 수집이 가능하기 때문에 조사비용이 거의 들지 않아도 되어 경제적이고, 둘째로 전통적인 수요예측방법들에서 요구되어지는 복잡한 모형수립 및 계수조정(Parameter Calibration)이 필요하지 않아 간편하고 셋째로 오래전에 작성된 기종점 통행표를 단순히 링크 교통량 자료만을 이용하여 쉽게 보완할 수 있어 지속적인 자료의 축적(Data Age-ing)이 가능하며 더 나아 가서 소위 연속적인 교통 계획 및 교통시설관리(Continuous Transport Planning and Management)를 가능케 하는 등의 여러 장점 때문에 많은 주목을 받아 오고 최근 몇 년이 꾸준히 실무에 유용하게 적용이 되고 있는 실정이다. 본 연구는 링크 교통량자료를 이용하여 기종점 통행표를 작성하기 위하여 개발된 기존의 여러 기법들 가운데 특히 용량제약조건(Capacity-Restrained Condition)하에서 기존의 방법들을 상호 검토한 후 Wardrop의 교통망 평형원칙(Wardrop's First Network Equilibrium Principle)을 만족하는 새로운 추정기법을 제의하고 이의 시험결과를 논의하는 것을 주요내용으로 한다. 링크 교통량 자료를 이용하여 기종점 통행표를 작성하는 기법들의 근본 목표는 조사된 링크 교통량(Ob-served Traffic Counts)에 가장 근접한 교통망 통행 배정 링크 교통량(Assigned Link Volumes)을 재현(Re-producing)할 수 있는 기종점 통행표들 중에서 최적의 기종점 통행표를 발견하는 것이다. 따라서 교통망에서 통행자의 여행 경로 배정을 가장 잘 반영할 수 있는 현실적인(Realistic) 교통망 통행 배정 모형(Net-work Traffic Assignment Model)의 선택은 중요한 요소가 되며 특히 교통망에 교통체증(Traffic Conges-tion)이 심할 경우 교통망 통행자 평형조건(Network Traffic Equilibrium Condition)을 고려하기 위한 특별한 처리가 요구되어진다. 본 연구는 Whllumsen(Hall, Van Vliet and Willumsen, 1980)에 의하여 개발된 ME2(Maximum Entropy Matrix Estimation)기법에서 반복식 추정방법(Sequential Estimation Method)을 사용할 경우 Wardrop의 평형조건을 만족하는 기종점 통행표를 구할 수 없다는 단점을 극복하기 위한 방안으로서 엔트로피 극대화문제와 교통망 평형 조건(Entropy Maximisation and Network Equilibrium Condition)의 두 문제를 동시에 해결할 수 있는 새로운 수식모형과 이를 풀기 위한 알고리즘(Simultaneous Solution Algorithm)을 제의하였다. 제의된 수식모형과 알고리즘을 예제 교통망(Example Network)을 이용한 시험하고 그 결과를 ME2 의 반복식 추정 방법으로부터 구한 기종점 통행표와 비교 검토하였다.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.21 no.5
• /
• pp.15-27
• /
• 2022

An omnidirectional VR treadmill is a highly-immersive walking simulator that allows identical body movements, such as walking, running, and sitting. However, the operation difficulty of an omnidirectional VR treadmill may cause data reliability problems. Therefore, this study aims to verify the effectiveness of a VR treadmill by comparing the ability to orient in the real and virtual worlds spatially. For this purpose, a rotating and searching path experiment was conducted with participants. This experiment showed that there was no statistically significant difference in the ability of the participants to orient in the real and virtual worlds spatially. In addition, the omnidirectional VR treadmill requires an adaptation time for the users due to the difficulty in the treadmill operation. However, there was no significant difference in the difficulty felt by the participants according to the adaptation time. Hence, these findings supported the possibility of collecting realistic walking data without safety concerns through an omnidirectional VR treadmill. Furthermore, this treadmill could be used in future research to solve problems directly related to pedestrian safety, such as the interaction between vehicles and pedestrians.

• Journal of the Korea Convergence Society
• /
• v.8 no.12
• /
• pp.275-281
• /
• 2017

The automobile cowl cross bar which is a backbone frame part inside the cockpit module has been designed with more complex geometries recently due to demands of its enhanced functions and reduced weight of car. The traditional manufacturing process using welding between tubes with different diameters shows several problems such as poor mechanical characteristics and appearance, etc. Therefore, in this study, manufacturing processes which can eliminate the welding process were developed by applying one-piece metal forming processes such as tube drawing and radial swaging. As results, it was found that the one-piece manufacturing processes give better bending strength than the traditional welding process and the swaging process shows the lowest manufacturing cost.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.38 no.3
• /
• pp.1-7
• /
• 2015

This research is to develop a possible process to apply k-means clustering to an efficient vehicle routing process under time varying vehicle moving speeds. Time varying vehicle moving speeds are easy to find in metropolitan area. There is a big difference between the moving time requirements of two specific delivery points. Less delivery times are necessary if a delivery vehicle moves after or before rush hours. Various vehicle moving speeds make the efficient vehicle route search process extremely difficult to find even for near optimum routes due to the changes of required time between delivery points. Delivery area division is designed to simplify this complicated VRPs due to time various vehicle speeds. Certain divided area can be grouped into few adjacent divisions to assume that no vehicle speed change in each division. The vehicle speeds moving between two delivery points within this adjacent division can be assumed to be same. This indicates that it is possible to search optimum routes based upon the distance between two points as regular traveling salesman problems. This makes the complicated search process simple to attack since few local optimum routes can be found and then connects them to make a complete route. A possible method to divide area using k-means clustering is suggested and detailed examples are given with explanations in this paper. It is clear that the results obtained using the suggested process are more reasonable than other methods. The suggested area division process can be used to generate better area division promising improved vehicle route generations.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.3
• /
• pp.461-471
• /
• 1989

For the mixed-mode crack problems the direction of crack growth, the crack path and the rational representation of fatigue crack growth rates should be studied to predict fatigue life and safety of structures. In this study, a round specimen which produce nearly identical effects in all loading directions is proposed to make an easy measurement of initial direction of crack growth. The mode I and mode II stress intensity factors of the specimen were calculated using finite element method, in which the square root singular stresses at the crack tip are modeled by means of four rectangular quarter-point eight-noded elements surrounding the crack tip. Experimental results for high strength aluminum alloy showed that the direction of mixed-mode crack growth agree well with maximum principal stress criterion as well as minimum strain energy density criterion, but not with maximum shear stress criterion. From data of fatigue crack growth rates using crack geometry projected on the line perpendicular to the loading direction it is easily established that mixed-mode fatigue crack growth in 5083-H115 aluminum alloy goes predominantly with mode I crack growth behaviors.

• Journal of Korea Society of Industrial Information Systems
• /
• v.25 no.2
• /
• pp.39-47
• /
• 2020

This paper introduces a novel system-level framework that derives energy efficient electric vehicle (EV) driving speed profile to extend EV driving range without additional cost. This paper first implements an EV power train model considering forces acting on a driving vehicle and motor efficiency. Then, it derivate the minimum-energy driving speed profile for a given driving mission defined by the route. This framework first formulates an optimization problem and uses the dynamic programming algorithm with a weighting factor to derive a speed profile minimizing both of energy consumption and driving time. This paper introduces various weighting factor tracking methods to satisfy the driving time constraint. Simulation results show that runtime of the proposed scaling algorithm is 34% and 50% smaller than those of the binary search algorithm and greedy algorithm, respectively.

• Journal of the Korean Institute of Gas
• /
• v.25 no.3
• /
• pp.16-26
• /
• 2021

The global warming problem has arose, the supply eco-friendly vehicles such as HFCEVs is increasing around world and Korea is fully supporting subsidies, tax cut to form an initial market for HFCEVs. The key to the safety of HFCEVs is pressure vessels stored hydrogen, and although these pressure vessels must be inspection regularly, the existing inspection stations are insufficient to meet the demand for inspection. Therefore, it is important to establishment of pressure vessels inspection station for safety management of HFCEVs. In this study, it estimates innovation coefficient, imitation coefficient in Bass model by using electric vehicle sales data, and foretasted the supply of HFCEVs by region & the demand for inspection by region using the Bass diffusion model. As a result, the inspection demand for pressure vessels in HFCEVs in 2040 was 690,759 units, and it was confirmed 191 new inspection stations and 1,124 inspectors were needed to prepare for this.

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.2
• /
• pp.374-384
• /
• 2016

Concern about air pollution is gradually rising up in domestic and foreign, automotive and fuel researchers are trying to reduce vehicle exhaust emissions, through a lot of approaches, which consist of new engine design and innovative after-treatment systems, using clean (eco-friendly alternative) fuels and fuel quality improvement. This research is proceeding by two main issues : exhaust emissions and PM particle emissions of gasoline vehicle. Exhaust emissions, non-regulated emissions and PM (particulate matter) particles of automotive are causing many problems which ambient pollution and harmful effects on the human body. The main particulate fraction of automotive exhaust emissions consists of small particles. Because of their small size, inhaled particles can easily penetrate deep into the lungs. The rough surfaces of these particles make it easier for them to combine with other toxins in the environment. Thus, the hazards of particle inhalation are increased. Based on the oxygenated fuel additive types (MTBE, Bio-ETBE, Bio-ethanol, Bio-butanol), this paper discussed the influence of oxygen contents on gasoline vehicle exhaust emissions, non-regulated emissions and nano-particle emissions. Also, this paper assessed exhaust emission characteristics at 2 type test modes. The test modes were FTP-75 and HWFET. All measurement items be verified less than the value of regulated emissions. It could be known difference increase and decrease by each measurement item depending on increase the oxygen contents.