• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.13 no.1
• /
• pp.16-29
• /
• 1991

The occurrence of thrombotic occlusion & endothelial injuries at the site of anastomosis have been considered as major problems in microvascular surgery. The purpose of this study was to ascertain whether a end-in-end(sleeve, telescope) anastomosis compared favorably with end-to-end anastomosis in healing procedures on the endothelium and to study the possibility of clinical application in end-in-end method. The microvascular anastomoses have been performed with end-in-end method in the femoral arteries of 20 rats group, also with end-to-end method on the same arteries of another 20 rats group, and then the four anastomosed vessels in subdivided groups on each group were taken after period of 1, 3, 7, 14, 21 days following by anastomoses for scanning electron microscope observation. The results were as following: 1. The patency rate was 90% in the end-in-end group and 85%in the end-to-end group and late thrombus occurred at 7, 14 days on both groups, which suggested -consistent monitoring of patency was required for two weeks at least. 2. Platelet aggregates at the site of anastomosis began to organize on post-operation 3 days and in the end-in-end group, the initially decreased lumen of inserted vessel was gradually increasing on 7 days due to atrophy of the medial layers. 3. Re-endothelialization was completed between 7 and 14 days in end-in-end group, whereas between 14 and 21 days in end-to-end group.

• Clean Technology
• /
• v.24 no.1
• /
• pp.9-14
• /
• 2018

In this study, Material life cycle evaluation was performed to analyze the environmental impact characteristics of TiN-Zr membrane manufacturing process. The software of MLCA was Gabi. Through this, environmental impact assessment was performed for each process. Transition metal nitrides have been researched extensively because of their properties. Among these, TiN has the most attention. TiN is a ceramic materials which possess the good combination of physical and chemical properties, such as high melting point, high hardness, and relatively low specific gravity, high wear resistance and high corrosion resistance. With these properties, TiN plays an important role in functional materials for application in separation hydrogen from fossil fuel. Precursor TiN was synthesized by sol-gel method and zirconium was coated by ball mill method. The metallurgical, physical and thermodynamic characteristics of the membranes were analyzed by using Scanning Electron Microscope (SEM), Energy Dispersive X-ray (EDS), X-ray Diffraction (XRD), Thermo Gravimetry/Differential Thermal Analysis (TG/DTA), Brunauer, Emmett, Teller (BET) and Gas Chromatograph System (GP). As a result of characterization and normalization, environmental impacts were 94% in MAETP (Marine Aquatic Ecotoxicity), 2% FAETP (Freshwater Aquatic Ecotoxicity), 2% HTP (Human Toxicity Potential). TiN fabrication process appears to have a direct or indirect impact on the human body. It is believed that the greatest impact that HTP can have on human is the carcinogenic properties. This shows that electricity use has a great influence on ecosystem impact. TiN-Zr was analyzed in Eco-Indicator '99 (EI99) and CML 2001 methodology.

• Tuberculosis and Respiratory Diseases
• /
• v.45 no.5
• /
• pp.1073-1081
• /
• 1998

Primary pulmonary lymphoma (PPL) is an uncommon tumor, which constitutes 3-4% of all extranodal lymphomas and 0.3-0.5 % of all primary pulmonary malignant tumors. Low-grade B-cell lymphomas of bronchus-associated lymphoid tissue (BALT) accounted for the majority of PPL. This BALT lymphomas are frequently asymptomatic and have an excellent prognosis and an indolent clinical course by contrast with T-cell type. Therefore, determination of the B- or T-immunophenotype of the tumor cells is known to be very important from a clinical aspect. Recent advances in immunohistochemical techniques, cytogenetics, and molecular biology have allowed better definition of type, maturation, and clonality of lymphoma cells and have made it possible to better understand the PPL. We experienced an asymptomatic 43-year-old man who was evaluated for infiltrates on both sides discovered incidentallly after a routine chest roentgenogram. He was eventually diagnosed as low-grade B-cell lymphoma of BALT by immunohistochemical staining from specimens obtained by open lung biopsy. He was treated with combination chemotherapy. At follow up 12 mons following initial diagnosis, he remains in stable. We report this case, who showed a relatively favorable prognosis and indolent clinical course compatible with low-grade B-cell lymphoma.

• Journal of the Korean Ceramic Society
• /
• v.40 no.9
• /
• pp.867-873
• /
• 2003

$Si_{3}N_{4}$-BN based machinable ceramics were fabricated by hot-pressing at $1800^{\circ}C$ for 2 h under a pressure of 25 MPa. The microstructure, mechanical properties, and machinability were investigated. With increasing h-BN content from 5 vol% to 30 vol%, three point flexural strength decreased from 1000 MPa of monolithic S $i_3$ $N_4$ to 720～400 MPa. The fracture toughness, $K_{IC}$ , was decreased from 7.6 MPaㆍ$m^{1/2}$ of monolithic S $i_3$ $N_4$ to 6.5～4.1 MPaㆍ$m^{1/2}$. The grain size and aspect ratio of $\beta$-S $i_3$ $N_4$ slightly decreased with increasing h-BN content. S $i_3$ $N_4$ monolith could not be machined due to brittle fracture, but S $i_3$ $N_4$-BN based machinable ceramics could be machined without fracture, showing excellent machinability. With increasing h-BN content, the thurst force during cutting and micro-drilling process was decreased.

• Journal of the Korean Ceramic Society
• /
• v.47 no.5
• /
• pp.467-473
• /
• 2010

The objective of this study is to prepare lead-free thick film resistor (TFR) paste compatible with AlN substrate for hybrid microelectronics. For this purpose, CaO-ZnO-$B_2O_3-Al_2O_3-SiO_2$ glass system was chosen as a sintering aid of $RuO_2$. The effects of the weight ratio of CaO to ZnO in glass composition, the glass content and the sintering temperature on the electrical properties of TFR were investigated. $RuO_2$ as a conductive and glass powder were dispersed in an organic binder to obtain printable paste and then thick-film was formed by screen printing, followed by sintering at the range between $750^{\circ}C$ and $900^{\circ}C$ for 10 min with a heating rate of $50^{\circ}C$/min in an ambient atmosphere. The addition of ZnO to glass composition and sintering at higher temperature resulted in increasing sheet resistance and decreasing temperature coefficient of resistance. Using $RuO_2$-based resistor paste containing 40 wt%glass of CaO-20.5%ZnO-25%$B_2O_3$-7%$Al_2O_3$-15%$SiO_2$ composition, it is possible to produce thick film resistor on AlN substrate with sheet resistance of $10.6\Omega/\spuare$ and the temperature coefficient of resistance of 702ppm/$^{\circ}C$ after sintering at $850^{\circ}C$.

• Journal of Korea Soil Environment Society
• /
• v.3 no.1
• /
• pp.11-20
• /
• 1998

Inorganic nitrogens resulting from fertilizers are possible contaminants of bank-filtered ground water, which is an alternative source of safe drinking water. We conducted a laboratory study to determine the fate of inorganic nitrogens in the near field of bank filtration sites and we consequently illustrated the effects of these possible contaminants on the water quailty of bank filtration. Soil properties were found to be well equivalent to those of other cultivated field soils in Korea. Surface soil pH was about 4.3 which is slightly lower than average level. Overall, diverse concentrations of $NO_3$-N and $NH_3$-N were measured, and $NO_2$-N was nearly undetected. $NH_3$-N level in the field decreased, while $NO_3$-N increased along with increasing depth of unsaturated zone. Numbers of viable and nitrifying bacteria ranged from 6.73$\times$$10^{6}$to 10.7$\times$$10^{6}$ and 0.44$\times$$10^{4}$ to 5.21$\times$$10^{4}$ respectively, and both of them were highly correlated ($R^{2}$=0.992). Nitrifying potential assayed by batch test showed relatively lower than other reported results. The oxygen uptake potential of surface and subsurface soil was measured in the presence of ${(NH_4)_2}$$SO_4$. The results demonstrated that surface soil required shorter lag period and uptaked more oxygen than subsurface's.

• Tunnel and Underground Space
• /
• v.15 no.3 s.56
• /
• pp.223-227
• /
• 2005

The physical and mechanical properties of volcanic glass, which is distributed in the Samho area, South Korea were studied. Laboratory rock tests were carried out in order to obtain the various properties of rocks. Specific gravity, water content, absorption, porosity and wave velocity were measured for the physical properties. Uniaxial and triaxial compressive tests, Brazilian test and point load test were also performed for the mechanical properties. The tests of volcanic glass revealed that the apparent specific gravity, water content and absorption were 2.28, $1.67\%$ and $1.72\%$, respectively. Porosity $(3.87\%)$ was lower, whereas P-wave velocity (5330m/s) and S-wave velocity (2980 m/s) were relatively higher. Brazilian tensile strength ot 7.2MPa, and point load strength of 2.6MPa were among the mechanical properties of the rock. Uniaxial compressive strength (62.4MPa) estimated ken point load strength was very closed to the value (66.0MPa) from the uniaxial compressive test. Young's modulus and Poisson's ratio were E=43.2 GPa and v=0.28, respectively. Drawing the tangent line to Mohr-Coulomb failure criterion showed the cohesion of 20.1MPa and internal fraction angle of $28.6^{\circ}$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.123-123
• /
• 2010

3족 질화물계 물질은 발광다이오드와 같은 광전자소자적용에 있어서 매우 우수한물 질이다.일반적으로, GaN 에피 성장에 있어서 저온 중간층을 삽입한 2 단계 성장 방법은 낮은 결함밀도와 균일한 표면을 얻기 위해 도입된 기술이다. 특히 AlN 중간층은 GaN 중간층과 비교하였을 때 결정성뿐만 아니라 높은 온도에서의 열적안정성, GaN 기반의 자외선 검출기서의빛 흡수 감소 등의 장점을 가지고 있다. 또한 패턴 사파이어 기판위 GaN 에피 성장은 측면성장 효과를 통해 결함 밀도 감소와 광 추출 효율을 향상시키는 것으로 알려져 있다.또한 열응력으로 인한 기판의 휨 현상은 박막성장중 기판의 온도 분포를 불균일하게 만드는 원인이 되며 이는 결국 박막 조성 및 결정성의 열화를 유도하게 되고 최종적으로 소자특성을 떨어 뜨리는 원인이 되는데 AlN 중간층의 도입으로 이것을 완화시킬 수 있는 효과가 있다. 하지만, AlN 중간층이 패턴된 기판 위에 성장시킨 GaN 에피층에 미치는 영향은 명확하지 않다. 본 연구팀은 일반적인 c-plane 사파이어 기판과 플라즈마 건식 에칭을 통한 렌즈 모양의 패턴된 사파이어 기판을 이용해서 AlN 중간층과 GaN 에피층을 유기금속 화학기상증착법으로 성장하였다. 특히, 렌즈 모양의 패턴된 사파이어 기판은 패턴 모양과 패턴 밀도가 성장에 미치는 영향을 연구하기 위해 두가지 패턴의 사파이어 기판을 이용하였다. AlN 중간층 두께를 조절함으로써 최적화된 GaN 에피층을 90분까지 4단계로 시간 변화를 주어 성장 양상을 관찰한 결과, GaN 에피박막의 성장은 패턴 기판의 trench 부분에서 시작하여 기판의 패턴부분을 덮는 측면 성장을 보이고있다. 또한 TEM과 CL을 통해 GaN 에피박막의 관통 전위를 분석해 본 결과 측면 성장과정에서 성장 방향을 따라 옆으로 휘게 됨으로 표면까지 도달하는 결정결함의 수가 획기적으로 줄어드는 것을 확인함으로써 고품질의 GaN 에피층을 성장시킬 수 있었다. 그리고 패턴밀도가 높고 모양이 볼록할수록 측면 성장 효과로 인한 결정성 향상과 난반사 증가를 통한 임계각 증가로 광추출 효율이 향상 되는 것을 확인할 수 있었다. 이러한 결과를 바탕으로 최적화된 AlN 중간층을 이용하여 패턴 기판위에서 고품질의 GaN 에피층을 성장시킬 수 있었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.125-125
• /
• 2010

극성 [0001] 방향으로 성장된 질화물 기반의 LED (light emitting diode) 는 분극현상에 의해 발생하는 강한 내부 전기장의 영향을 받게 된다. 이러한 내부 전기장은 양자우물 내의 전자와 정공의 공간적 분리를 야기하고 quantum confined Stark effect (QCSE)에 의한 발광 파장의 적색 편이가 발생하며 양자효율의 저하를 가져오게 된다. 이러한 문제를 해결하기 위해 InGaN/GaN이나 AlGaN/GaN 양자 우물구조를 GaN의 m-plane (1$\bar{1}$00) 이나 a-plane (11$\bar{2}$0) 등 비극성면 위에 성장하려는 시도를 하고 있다. 그러나 비극성 면의 비등방성 (anisotropy) 으로 인하여 결정성이 높은 비극성 GaN을 성장하는 데에는 많은 어려움이 있다. GaN 층의 표면을 평탄화하고 결정성을 향상시키기 위해서 저온 GaN 또는 AlN 버퍼층을 성장하는 2단계 방법이나 고온 버퍼층을 이용하여 성장하는 연구들이 많이 진행되고 있다. 본 연구에서는 고온 GaN 버퍼층을 이용하여 기존의 2단계 성장과정을 단순화한 비극성 a-plane GaN을 r-plane 사파이어 기판위에 유기금속 화학증착법 (MOCVD)으로 성장하였다. 사파이어 기판위에 AlN 층을 형성하기 위한 nitridation 과정 후 1030 도에서 두께 45 ~ 800 nm의 고온 GaN 버퍼층을 성장하고 총 박막 두께가 2.7 ~ 3 um 가 되도록 a-plane GaN을 성장하여 표면 양상의 변화와 결정성을 확인하였다. 또한 a-plane GaN 박막 성장 시에 성장 압력을 100 ~ 300 torr 로 조절하며 박막 성장의 변화 양상을 관찰하였다. 고온 GaN 버퍼층 성장 두께가 감소함에 따라 결정성은 증가하였으나 표면의 삼각형 형태의 pit 밀도가 증가함을 확인하였다. 또한 성장 압력이 감소함에 따라 표면 pit은 감소하였으나 결정성도 감소하는 것을 확인하였다. 성장 압력과 버퍼층 성장 두께를 조절하여 표면에 삼각형 형태의 pit이 존재하지 않는 RMS roughness 0.99 nm, 관통전위밀도 $1.78\;{\times}\;10^{10}/cm^2$, XRD 반가폭이 [0001], [1$\bar{1}$00] 방향으로 각 798, 1909 arcsec 인 a-plane GaN을 성장하였다. 이 연구를 통해 고온 GaN 버퍼 성장방법을 이용하여 간소화된 공정으로 LED 소자 제작에 사용할 수 있는 결정성 높은 a-plane GaN을 성장할 수 있는 가능성을 확인하였다.

• Korean Journal of Materials Research
• /
• v.9 no.6
• /
• pp.577-582
• /
• 1999

In order to make the electroconductive $Si_3N_4$-TiN composities, the Si-Ti(N) compacts were nitrided at $1450^{\circ}C$ for 20hours, and then they were post-sintered by a gas-pressure-sintering technique at 1TEX>$1950^{\circ}C$ for 3.5 hours. As starting powders, commercial si powder of about $10\mu\textrm{m}$, two types of Ti powders of 100 and 325 mesh, and fine-sized TiN of $2.5\mu\textrm{m}$ powders were used. In the $Si_3N_4$-TiN sintered bodies used Ti powders, the relative density and fracture strength and electrical conductivity are low due to the existence of large amounts of coarse pores. However, in the $Si_3N_4$-TiN composite used TiN powder, the fracture toughness, fracture strength and electrical resistivity were $5.0MPa{\cdot}m^{1/2}$, 624MPa and $1400{\omega}cm$, respectively. The dispersion of TiN particles in the composite inhibited the growth of $Si_3N_4$ in the shape of rod and made strong strain field contrasts at the $Si_3N_4$-TiNinterfaces. It was recognized that microstructural control is required to improve the electrical conductivity and mechanical properties of $Si_3N_4$-TiN composites by dispersing TiN particles homogeneously.