• Korean Journal of Environmental Biology
• /
• v.39 no.2
• /
• pp.218-224
• /
• 2021

This study was conducted to determine the mass-loss rates and the changes in carbon/nitrogen (C/N) ratio of dead woods, which were of following species: Dryobalanops aromatic, D. rappa, and Cratoxylum arborescens. These were dominant tree species in mixed Dipterocarp forests (MDF) and peat swamp forests (PSF) in Brunei Darussalam. In May, 2019, 48 dead wood samples (15 cm×4.8 cm×5 cm) were placed in MDF and PSF sites, and all the samples were collected after 16 months. The effects of species on mass loss were statistically significant (p<0.05); however, no difference was observed in the mass loss obtained from the two forest types (p>0.05). The initial density (g·cm^-3) of the dead woods D. aromatic, D. rappa, and C. arborescens, was 0.64±0.02, 0.60±0.00, and 0.44±0.01, respectively. Also the annual mass loss rate (%) was estimated to be 6.37, 8.17, and 18.53 for D. aromatic, D. rappa, and C. arborescens, respectively. The proportion of dead woods in decay class III was only 25% of C. arborescens samples, which were attacked by wood-feeding invertebrates, such as termites. The C/N ratio decreased significantly in D. aromatic and D. rappa, but the decreasing trend of C/N ratio was not statistically significant in C. arborescens. The results indicate that physical traits of dead woods, such as density, could be one of the main factors causing the decomposition of dead woods initially, as invertebrates such as termites are one of the key decomposers of dead wood in tropical rainforests. In the samples of C. arborescens, which was attacked by invertebrates, nitrogen immobilization occurred to lesser extent as compared to that observed in D. aromatic and D. rappa.

• Journal of the Korea Institute of Building Construction
• /
• v.9 no.6
• /
• pp.113-119
• /
• 2009

This study is to investigate the fundamental and fireproof qualities of high strength concrete corresponding to changes in the curing factors and the PP fiber ratio. The results were as follows. For the fundamental characteristics of concrete, the fluidity was reduced in proportion to the increase in the PP fiber ratio. The compressive strength was somewhat reduced according to an increase in the PP fiber ratio. However, it had the high strength scope of more than 60 MPa at 7 days and of more than 90 MPa at 28 days. On the spalling mechanism followed by changes of the water content ratio, spalling was prevented in all combinations, except the specimen without PP fiber and subjected to 3.0% of moisture contents. When spalling was prevented at that time, the residual compressive strength ratio was 22%~41% and the mass reduction ratio was 5%~7%, which was relatively favorable. As the spalling mechanism corresponds to changes in the curing method, spalling was prevented in concrete with a PP fiber mixing ratio of more than 0.05% in the event of standard curing, and in concrete with a PP fiber mixing ratio of more than 0.10% in the case of steam curing and autoclave curing. In these cases, when spalling was prevented, the residual compressive strength ratio was 23~42% and the mass reduction ratio was 7~11%. In these results, the ease of spalling prevention in high strength concrete was inversely proportional to the water content ratio. Depending on the curing method, spalling was prevented in concrete with over 0.05% PP fiber with standard curing and in concrete with over 0.1% PP fiber with steam curing and autoclave curing.

• Journal of Soil and Groundwater Environment
• /
• v.12 no.6
• /
• pp.17-25
• /
• 2007

Convergent flow tracer test for 2 m (IW-1 well) and 5 m (IW-2 well) of test scale was conducted at the alluvial aquifer with high permeability and storativity. Pumping rate for convergent flow tracer test were $2,500m^3/day$, and the chloride tracer of 5 kg was instantaneously injected into IW-1 and IW-2 wells. Differences of first arrival time and peak concentration were analyzed by using the concentration breakthrough curves of chloride. Recovered chloride mass were analyzed by recovered cumulative mass curves. And, increment and decrement for chloride concentration were analyzed through chloride concentration versus recovered cumulative mass ratio graphs. Also, increment and decrement ratios of chloride concentration were estimated through linear regression analyses for increment and decrement intervals of chloride concentration. Longitudinal dispersivities were estimated by quot;Converging Radial Flow With Instantaneous Injectionquot; method using CATTI code. Longitudinal dispersivities estimated by CATTI code were 0.4152 m between pumping well and IW-1 well, and 3.2665 m between pumping well and IW-2 well. Longitudinal dispersivity was increased according to far distance from the pumping well. The longitudinal dispersivity according to distance were estimated as 0.21 between pumping well and IW-1 well, and 0.65 between pumping well and IW-2 well.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.103-103
• /
• 2017

증발기의 형태에 따라 수치적 해석을 진행하면서 최적의 효율을 나타낼 수 있는 증발기를 설계하는 것이 중요하다. 증발기의 수치적 해석은 EES 프로그램을 이용하여 진행되었으며, 계산의 검증은 자사의 제품의 성능과 비교하면서 검증하였다. 증발기의 수치적 해석의 구성은 지배방정식과 연속방정식을 이용하여, 냉매의 총괄열전달계수, 관내외벽의 열전도율, 공기의 총괄열전달계수를 이용하여 총괄열전달계수를 계산하였으며, 총괄열전달계수를 이용하여 증발기의 열량을 계산하였다. 증발기의 수치적 해석과 자사 제품 5개의 제품과 비교하였고, 평균적으로 약 10%의 오차율을 보였다. 신뢰성이 확보된 계산식을 이용하여 Fin의 간격, 단위 질량유량, 열 교환 코일 길이, 풍량의 조건을 각각 변동시켜 증발기 열량 비교를 하며 경향성을 고찰하였다. Fin의 간격을 1mm에서 20mm으로 0.5mm 간격으로 변화 시켰을 경우, 핀 간격이 좁으면 공기 유속이 빨라져 열 교환 효율이 낮아지며, 반대로 넓어지면 냉매 유량에 비해 공기 유량이 많기 때문에 열 교환 효율이 낮아진다. 열 교환 코일 길이를 500mm에서 2400mm으로 50mm 간격으로 변화 시켰을 경우, 열 교환 코일 길이가 길어질수록 배관의 마찰력과 냉매의 온도 상승으로 인하여 공기 온도와의 온도 차이가 줄어들어 열 교환 효율은 낮아진다. 풍량을 20cmm에서 400cmm으로 10cmm 간격으로 변화 시켰을 경우, 일정 풍량 이상 올라가면 공기 유속이 빨라져서 열량이 낮아지는 경향을 보인다. 질량유량을 3g/sec에서 174g/sec으로 4.5g/sec 간격으로 변화 시켰을 경우, 질량 유량에 따라 비례적으로 열량이 높아지는 경향을 보이다가 일정 질량 유량 이상에서는 공기 풍량에 비해 냉매 유량이 많기 때문에 반비례적으로 열량이 낮아진다. 이처럼 증발기의 설계는 Fin 간격, 열 교환 코일 길이, 풍량, 질량유량 등을 복합적으로 고려하여 증발기 설계를 해야 하며, 저장고의 크기, 부하, 사용목적에 따라 최적화된 증발기를 설계하여야 한다.

• Journal of Korean Society on Water Environment
• /
• v.23 no.5
• /
• pp.683-688
• /
• 2007

Water flow into unsaturated soils is most often modeled by Richards equation consisting of the mass conservation law and Darcy's law. Three standard forms of Richards equation are presented as the head (${\Psi}$)-based form, the moisture content (${\theta}$) based form, and the mixed form. Numerical solutions of these partial differential equations with highly nonlinear terms can cause poor results along with significant mass balance errors. The numerical solution based on the mixed form of Richards equation is known that the mass is perfectly conserved without any additional computational efforts. The aim of this study is to develop fully implicit numerical scheme of Richards equation for one-dimensional vertical unsaturated flow in homogeneous soils using the finite difference approximation, and then to perform sensitivity analysis of infiltration to the variations in the unsaturated soil properties and to different soil types.

• Journal of Korean Association for Spatial Structures
• /
• v.7 no.2 s.24
• /
• pp.63-74
• /
• 2007

Large spatial structures consist of roof structure and its supporting structure. Authors simply call the supporting structure "lower parts" and roof structure "upper parts". To study the influence of an lower part on the seismic response of the upper part of a structure as a first step, authors substitute the upper part and the lower part of the structure to a single degree of freedom system individually, and set up a new 2 DOF structural model connected by them. It is clarified that the mass ratio and the period ratio of an upper part to a lower part are important parameters to find the amplification or reduction of the seismic response of an upper part.

• Fire Science and Engineering
• /
• v.22 no.5
• /
• pp.72-78
• /
• 2008

The mass loss rate and heat release rate of EPS sandwich panel cores were analysed using variable external irradiation level. The experimental materials were exposed to incident heat fluxes form 20 to 50 kW/$m^2$. For the measurement of mass loss rate and heat release rate, the size of specimen was $100mm{\times}100mm{\times}50mm$ and the samples were 3 different kinds. The combustion heat were carried out from the Oxygen bomb calorimeter and the mass loss rate and heat release rate were carried out from the Mass loss calorimeter according to ISO 5660-1. As the results of this study, the mass loss rate of Type A, B, and C were 2.7 g/$m^2s$, 2.8 g/$m^2s$, and 2.3 g/$m^2s$ and the heat release rate of Type A, B, and C were 58.23 kW/$m^2$, 47.19 kW/$m^2$, and 50.06 kW/$m^2$ respectively at the heat flux of 50 kW/$m^2$. In conclusion, when the heat release characteristics applied to a classification system of Canada, Type A and C can be classified grade C-3, and Type C can be classified grade C-2 from all data of this study.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.5
• /
• pp.476-482
• /
• 2009

The effect of pintle shape on the thrust level of pintle-nozzle Solid Rocket Motor(PNSRM) was studied numerically using the Spalart-Allmaras turbulent model of Fluent. Mass flow rate of PNSRM was always less than theoretical value and the extent of decrease in mass flow rate grew in the large pintle because of increase in the relative boundary layer thickness between pintle body and nozzle wall. The bigger pintle size was, the more thrust of pintle tip pressure was obtained. Meanwhile the more thrust of nozzle and chamber pressure decreased. Hence, total thrust of big pintle was less than a small pintle under same throat area condition. Specific impulse was relatively flat for all pintle shape.

• Journal of Astronomy and Space Sciences
• /
• v.11 no.1
• /
• pp.107-114
• /
• 1994

This paper describes a method for the determination of wind parameters as mass-loss rate, wind velocity, stochastic velocity in Zeta Aurigae type binaries. We have modified the Baade's (1989) computer code to analyze the wind parameters of Zeta Aurigae type binaries according to the least squares criterion. The modified program adjusts the wind parameters by the method of differential corrections. We have appled this method to the IUE observations of 32 Cygni. We have fitted a theoretical line profile to the IUE observations of Fe II resonance line at various phases. The mass-loss rate, wind velocity and stochastic velocity of 32 Cygni obtained in this paper are $2.18{\times}10^{-8}M_{\odot}/yr$, 132.14km/s, 39.82km/s, respectively.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.699-704
• /
• 2001

The purpose of this study is to present the atomization characteristics of 2-phase internal mixing nozzle. The obtained results are considered as the essential information of understanding the spray characteristics from the nozzle exit of an aerated nozzle. In this study, SMD and AMD are mainly measured at the distance of Z=10, 20, 50, 80, 120 and 170mm from the nozzle tip. The liquid flow rate was kept at 1.8g/s and the air feeding pressure was changed from 10kpa to 100kpa increasingly. The analysis of the acquired data was performed by 2-D PDPA system and in order to get the realibility, the number of data used in calculating the SMD & AMD were 10,000 samples.