• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.11
• /
• pp.94-100
• /
• 2014

In this paper, a design of low power Current-Reuse Voltage Controlled Oscillator (VCO) which has wide tuning range about 1.95 GHz ~ 3.15 GHz is presented. Class-C type is applied to improve phase noise and 2-Step Auto Amplitude Calibration (AAC) is used for minimizing the imbalance of differential VCO output voltage which is main issue of Current-Reuse VCO. The mismatch of differential VCO output voltage is presented about 1.5mV ~ 4.5mV. This mismatch is within 0.6 % compared with VCO output voltage. Proposed Current-Reuse VCO is designed using CMOS $0.13{\mu}m$ process. Supply voltage is 1.2 V and current consumption is 2.6 mA at center frequency. The phase noise is -116.267 dBc/Hz at 2.3GHz VCO frequency at 1MHz offset. The layout size is $720{\times}580{\mu}m^2$.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.2
• /
• pp.87-93
• /
• 2010

This paper presents a low-power, wide tuning range VCO with automatic two-step negative-Gm calibration loop to compensate for the process, voltage and temperature variation. To cover the wide tuning range, digital automatic negative-Gm tuning loop and analog automatic amplitude calibration loop are used. Adaptive body biasing (ABB) technique is also adopted to minimize the power consumption by lowering the threshold voltage of transistors in the negative-Gm core. The power consumption is 2 mA to 6mA from a 1.2 V supply. The VCO tuning range is 2.65 GHz, from 2.35 GHz to 5 GHz. And the phase noise is -117 dBc/Hz at the 1 MHz offset when the center frequency is 3.2 GHz.

• Korean Journal of Optics and Photonics
• /
• v.13 no.1
• /
• pp.58-64
• /
• 2002

Using Mach-Zehnder type intensity modulator, we stabilized a 10 GHz harmonically mode-locked dispersion-compensated fiber ring laser using a feedback controlling system, and we measured its stability. The laser was stabilized for more than 16 hours by controlling the cavity length to suppress the relaxation oscillation frequency component which had caused the laser output instability. The ms timing jitter and ms amplitude noise were measured to be 260-524 fsec and 4~11.5%, respectively, and BER test measurement showed a value of 10$^{-13}$ .

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.4 no.2
• /
• pp.417-426
• /
• 2000

In this paper, CE-CPSK(Constant Envelope Continuous Phase Shift Keying) modulated DS/SS(Direct Sequence Spread Spectrum) transceiver with 908 MHz carrier frequency and 1.5 MHz PN clock rate is proposed. To overcome the effect of nun-linear power amplifier, CE-CPSK modulation method which has the constant envelope and continuous phase characteristics is proposed. To analyze the DS/SS receiver performance with respect to code tracking loop, multipath fading channel is characterized as a two-ray Rayleigh fading channel. To compensate the demerit of analog delay locked loop, digital delay locked loop is employed for code tracking loop. Simulation and experimental examination has been carried out in AWGN(Additive White Gaussian Noise) and Rayleigh fading channel environment in order to prove validity of the proposed method.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.68-77
• /
• 2017

High-frequency combustion instability results from a feedback coupling between the unsteady heat release rate and the acoustic waves formed resonantly in the combustion chamber. It can be modeled as thermoacoustic problems with various degrees of the assumptions and simplifications. This paper presents numerical analysis of self-excited combustion instabilities in a variable-length lean-premixed combustor and designs of passive control devices such as baffle and acoustic resonators in a framework of 3-D FEM Helmholtz solver. Nonlinear behaviors such as steep-fronted shock waves and a finite amplitude limit cycle are also investigated with a compressible flow simulation technique.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.6
• /
• pp.575-583
• /
• 2003

In thesis we applied the short or open reflection type for IQ vector modulator The open or short type is operated even exception of other redundancy circuit. Generally IQ vector modulator uses MESFET in performing reflection open or short, then minus voltage which is having complex structure is required to operate MESFET via IQ signal. However BJT can be substituted for MESFET, BJT is improved characteristics like as cutoff frequency, electron mobility and so on. We used BJT in IQ vector modulator which is compatible with TTL level in I,Q digital signal, and attached AGC function. We got the result of operations within ${\pm}$ 1$^{\circ}$ phase and ${\pm}$ 0.6 dB amplitude Variation With full range of 20 dB and Variation of ${\pm}$ 6$^{\circ}$ Phase and ${\pm}$ 0.5 dB amplitude Versus full temperature range.

• Journal of the Institute of Convergence Signal Processing
• /
• v.19 no.2
• /
• pp.54-60
• /
• 2018

In this paper, we propose an efficient automatic control method for the collision avoidance of drones. In general, the drones are controlled by transmitting to the flight control (FC) module the received PWM signals transmitted from a RC controller which transduce movements of the knob into PWM signal. We implemented the collision avoidance module in-between receiver and FC module to monitor and change the throttle, pitch and roll control signals to avoid drone collision. In order to avoid the collision, a LiDAR distance sensor and a servo-motor are installed and periodically measure the obstacle distance within -45 degrees from 45 degrees in flight direction. If the collision is predicted, the received PWM signal is changed and transmitted to the FC module to prevent the collision. We applied our proposed method to a hexacopter and the experimental results show that the safety is improved because it can prevent the collision caused by the inadvertency or inexperienced maneuver.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.15 no.1
• /
• pp.253-259
• /
• 2015

In this paper, we propose a transformer of alternating voltage source utilizing a semiconductor, operating in bidirectional fashion. Transformer is a device transferring energy by inductive coupling between its winding circuits. Conventional transformer is a device, composed of a primary coil and a secondary coil, transforming an alternating voltage. The system we propose is designed with a single circuit transforming the level of voltage signal in two ways; from the source to the load, and vice versa. For semiconductor switches, the NPN transistor is connected to the alternating voltage source terminal, and emitter terminal is connected to the inductor in the system as an energy storage element. The control signal is applied to the base terminal of the semiconductors. We have shown that the system we propose, by adopting only one circuit, drives an alternating voltage transformer that changes the amplitudes of voltage signal in reciprocal way.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.2
• /
• pp.125-130
• /
• 2012

The nematode Caenorhabditis elegans is a widely used model organism in biological research. Thanks to the availability of well-established knowledge about its neural connectivity, a wide range of studies have been attempted to uncover the relationship between behaviors and the responsible neurons. In our research, the adaptive behavior of C. elegans in solid environments with different surface rigidities is investigated, where the worm adapts to different mechanical stiffnesses by modulating its crawling waveform. The amplitude and wavelength of the crawling waveform decrease as the environment becomes more rigid. Interestingly, the mechanosensation-defective mutant shows different responses to the surface rigidity compared to those of the wild-type worm. To explain the adaptation process in mechanically different environments, we suggest a plausible neural circuit model.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.2
• /
• pp.66-78
• /
• 2021

In this study, the effect of Symmetry Breaking was compared according to the equivalent ratio condition and the number of nozzles where combustion instability occurs in an annular combustor. Generally, due to the relatively short combustor length, a longitudinal instability was less likely to occur in the annular combustor, but the combustion instability sometimes happens when ducts such as transition piece in gas turbine power station are present. In this case, due to the duct, only the longitudinal instability mode is observed. The characteristics of Symmetry Breaking were investigated according to the number of five lean nozzles and the equivalent ratio combination, and as the equivalent ratio decreased, the effect of Symmetry Breaking rapidly occurred, and the instability was dramatically disappeared and the amplitude was greatly reduced. In addition, it was confirmed that as the number of lean nozzles increased, a phenomenon such as a reduction in the equivalent ratio appeared.