• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.329.1-329
• /
• 2002

To detect external vibration signals on the latticed fence structure, distributed fiber optic sensor using Sagnac interferometer was fabricated and tested. The latticed structure fabricated with dimension of 170cm in width and 180cm in height, the optical fiber, 50m in lengtn, distributed and fixed on the latticed structure. It was verified the sensitivity of the Sagnac interferometer using the PZT phase modulator. Fiber-optic external vibration signal applied to the latticed structure from 100㎐ to several ㎑. (omitted)

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1993.04a
• /
• pp.30-34
• /
• 1993

기계구조물이 고속화, 경량화 됨에 따라 더 정밀한 구조물의 설계 및 해석이 요구되어지고 있고, 이에 따라 단속적모형 보다 한 단계 더 나아가 분포변수 모형으로 구조물을 모형화하게 된다. 특히 나선형 스프링은 기계구조물에서 가장 널리 사용되는 일반적인 요소로서, 그 형상이 공간상의 굽은 봉 형상이 므로 연성된 편미분방정식 형태로 지배방정식이 기술된다. 나선형 스프링 해 석은 Michell(1890)과 Love(1899)의 정적해석을 시작으로 Phillips와 Costello [1]의 'SimpleTheory' 및 Wittrick [3]의 지배방정식등 매우 복잡한 연성된 편미분방정식 형태를 지니고 있다. 그러나 이와 같은 편미분방정식은 해석하 기가 매우 어려워 수치해법으로도 간단한 경우에 한해서만 해석하여 왔다. 본 연구에서는 이와 같은 연성된 편미분방정식을 해석하기 위하여 보다 구 조진동문제에 적합한 수치해법을 제안하고, 이를 이용하여 나선형 스프링의 강제과도진동 응답을 정확하고 효율적으로 구하였다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.207-212
• /
• 2001

In this paper, dynamic stability and vibration characteristics of a flexible shoe in drum brake systems are investigated. The frictional force between the drum and the shoe is assumed as a distributed frictional force, while the shoe is modeled as an elastic beam supported by two translational springs at both ends and elastic foundations. Governing equations of motion are derived by energy expressions, and numerical results are calculated by finite element method. Through the numerical simulation, critical distributed frictional forces are calculated by changing the stiffness of two translational springs and elastic foundation parameters. It is also shown that the beam loses its stability by flutter and divergence depending on the stiffness of elastic supports and elastic foundation parameters. Finally, the time responses of the beam corresponding to their instability types are demonstrated.

• The Journal of the Acoustical Society of Korea
• /
• v.16 no.6
• /
• pp.41-47
• /
• 1997

Beating phenomenon which is generated by two closely located natural frequencies is one of research tenet for King Song-Dok bell. In this paper, we investigate the vibration shape of these natural frequencies using very extensive experimental data. Vibration signals are sampled at 108 points around the bell using accelerometers. Measured signals are anlayzed in time and frequency domain. Twelve natural shapes under 800Hz are plotted.

• Journal of KSNVE
• /
• v.9 no.1
• /
• pp.103-112
• /
• 1999

A new modeling and analysis technique for one-dimensional distributed parameter systems is presented. First. discretized equations of motion in Laplace domain are derived by applying discretization methods for partial differential equations of a one-dimensional structure with respect to spatial coordinate. Secondly. the z and inverse z transformations are applied to the discretized equations of motion for obtaining a dynamic matrix for a uniform element. Four different discretization methods are tested with an example. Finally, taking infinite on the number of step for a uniform element leads to an exact dynamic matrix for the uniform element. A generalized modal analysis procedure for eigenvalue analysis and modal expansion is also presented. The resulting element dynamic matrix is tested with a numerical example. Another application example is provided to demonstrate the applicability of the proposed method.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1995.04a
• /
• pp.18-21
• /
• 1995

A numerical method is presented to obtain natural frequencies and mode shapes of the arbitrary tapered beams with static deflections due to arbitrary distributed dead loads. The differential equation governing the free vibration is derived and solved numerically. In the numerical example, the linearly tapered beams and both the triangular and sinusoidal distributed dead loads are chosen. The lowest three natural frequencies are reported and typical mode shapes are presented in the figure.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.601-606
• /
• 2004

This paper deals with friction-induced vibration of disc brake system under constant friction coefficient. A linear, lumped and distributed parameter model to represent the floating caliper disc brake system is proposed. The complex eigenvalues are used to investigate the dynamic stability and in order to verify simulations which are based on the theoretical model, the experimental modal test and the dynamometer test are performed. The comparison of experimental and theoretical results shows a good agreement and the analysis indicates that mode coupling due to friction force is responsible for disc brake squeal. And squeal type instability is investigated by using the parametric analysis. This indicates parameters which have influence on the propensity of brake squeal. This helped to validate the analysis model and establish confidence in the analysis results. Also they may be useful during system development or diagnostic analysis.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.220-225
• /
• 2003

Recent issue of optical actuator is applying to mobile device. It leads actuator to become smaller than conventional type. This paper proposes the design of micro actuator plate spring and analysis of its vibration characteristic. Considering natural frequency of spindle motor, 1st and 2nd eigenfrequency of micro actuator must avoid its natural frequency. First, magnetic circuit is designed by using fine pattern coil and magnetic force is acquired by simulation program. Then, concept design is achieved by topology optimization. From concept design, micro actuator plate spring is embodied through DOE(design of experiment). Finally, considering vibration characteristic simultaneously, optimal plate spring design is determined by RSM(response surface method).

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.460-465
• /
• 2002

The nonlinear vibration of the CRT shadow mask is analyzed in consideration of the V-shaped tension distribution and the effect of wire impact damping. The reduced order FEM model of the shadow mask is obtained from dynamic condensation for the mass and stiffness matrices. Damping wire is modeled using the lumped parameter method to effectively describe its contact interactions with the shadow mask. The nonlinear contact-impact model is composed of spring and damper elements, of which parameters are determined from the Hertzian contact theory and the restitution coefficient, respectively. The analysis model of the shadow mask with damping wires is experimentally verified through impact tests of shadow masks performed in a vacuum chamber. Using the validated analysis model of the shadow mask with damping wires, the‘design of experiments’technique is applied to search fur the optimal damping wire configuration so that the vibration attenuation of the shadow mask is maximized.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.8
• /
• pp.702-708
• /
• 2004

This paper deals with friction-induced vibration of disc brake system under constant friction coefficient. A linear, lumped and distributed parameter model to represent the floating caliper disc brake system is proposed. The complex eigenvalues are used to investigate the dynamic stability and in order to verify simulations which are based on the theoretical model, the experimental modal test and the dynamometer test are performed. The comparison of experimental and theoretical results shows a good agreement and the analysis indicates that mode coupling due to friction force is responsible for disc brake squeal. And squeal type Instability is Investigated by using the parametric analysis. This indicates parameters which have influence on the propensity of brake squeal. This helped to validate the analysis model and establish confidence in the analysis results. Also they may be useful during system development or diagnostic analysis.