• Journal of the Korean GEO-environmental Society
• /
• v.15 no.1
• /
• pp.53-62
• /
• 2014

In Korea, in general, separation distance between existing parallel tunnels was set at two to five times as distant as the diameter of the tunnels according to ground conditions. Recently, however, actual applicability of closely spaced parallel tunnels whose distance between tunnel centers was shorter than the diameter has increased due to environmental damages resulting from massive cutting, restriction in purchase of required land, and maintenance of linear continuity. In particular, when the pillar width of tunnel decreases, the safety of pillars affects behaviors of the tunnel and therefore the need for diverse relevant studies has emerged. However, research so far has been largely confined to analysis of behavior characteristics of pillars, or parameters affecting design, and actually applicable and quantitative data have not been presented. Accordingly, in order to present a stability evaluation method which may maximally reflect construction conditions of spots, this study reflected topographical and stratigraphic characteristics of the portal part with the highest closeness between the tunnels, simulated multi-layer conditions with rock mass and complete weathering, and assessed the degree of effect the stability of pillars had on the entire tunnels through numerical analysis according to changes in pillar width by ground strength. This study also presented composite analysis result on ground surface settlement rates, interference volume rates, and average strength to stress and a formula, which may be applicable to actual work, to evaluate safety rates of closely spaced parallel tunnel pillars and minimum pillar width by ground strength based on failure criteria by Hoek-Brown (1980).

• Journal of Dental Rehabilitation and Applied Science
• /
• v.33 no.2
• /
• pp.97-105
• /
• 2017

Purpose: The purpose of this study was comparing the efficacy of passive irrigation (PI) and passive ultrasonic irrigation (PUI) for ability to remove debriment of canals. Materials and Methods: Mandibular premolars were decoronated and standardized to 16 mm length. After root canal enlargement and half separating longitudinally, standardized groove of 4 mm length, 0.2 mm width and 0.5 mm depth were formed on the dentin wall of one half. Three depressions in the canal wall of the opposite half, 0.3 mm in diameter and 0.5 mm in depth, were formed. After each groove and depression was filled with dentin debris, two sections of each half were reassembled using impression putty material. In group 1 the canals were irrigated with 2.5% NaOCl by PI. In group 2 the canals were irrigated with 2.5% NaOCl by PUI. Before and after root canal irrigation, the root canal wall of the section was taken with a microscope and a digital camera as images. The amount of dentin debris remaining in grooves and depressions was assessed using a scoring system. Results: There was no significant difference between PI and PUI except for the middle 1/3 of the root canal (P = 0.004). Conclusion: At the middle 1/3 of the root canal, PUI removed more dentine debris than PI. But the removal efficiency of dentin debris is not significantly different between the PUI and PI at the apical area of root canal in mandibular premolars.

• Journal of Korean Society of Forest Science
• /
• v.80 no.2
• /
• pp.220-231
• /
• 1991

The main purpose of this research is to standardize the logging operation with special reference to the net working time for thinning. This study was carried out to obtain the standard working method and working technique for Korean logging operation through the comparison of the present Korean working method and the German standard working method 1. The net working time devided into work elements showed little difference between those two working methods. 2. From the correlation analysis, net working time was significantly correlated with breast height diameter, the dependant variable, with the highest correlation coefficient in each species. 3. Total working time increases by 11 to 13 seconds to every 1 centimeter increase in breast height diameter from i to 16 centimeter. 4. The result of this study concluded that the German working method is recommended for improving the labour problems in the forest operation due to high wages and lack of manpower gradually increasing from now in Korea. In addition to the application of this standard working method, the technical training for the method should be done to the workers for improving the productivity.

• Journal of Bio-Environment Control
• /
• v.20 no.2
• /
• pp.78-82
• /
• 2011

Ventilation rates, inside and outside weather data were measured in a arch-shape single-span plastic greenhouse growing tomatoes. On the roof of the experimental greenhouse, round windows which have a diameter of 0.6 m were installed at intervals of 8m. It showed that the number of air changes in this greenhouse were average 0.17 volumes per minute and in the range of 0.02 to 0.32 volumes per minute. These air changes are insufficient to meet the recommended ventilation rate for commercial greenhouses, and it is estimated that interval of 6 m is appropriate for spring or fall season. For summer season, it is necessary to narrow the space or to enlarge the open area of roof windows. Using the heat balance model, the evapotranspiration coefficients of greenhouse tomatoes were estimated from experimental ventilation data, overall heat transfer and solar radiation. It showed that the evapotranspiration coefficients were average 0.62 and in the 0.39 to 0.85 range. We suggest applying 0.6 as the evapotranspiration coefficient in design of ventilation for the single-span tomato greenhouses.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.38 no.12
• /
• pp.1760-1766
• /
• 2009

Physical properties of Yukwa base extruded with glutinous rice flour, rice flour, defatted soy flour, and salt using an twin-screw extruder were investigated. The ingredients were extruded at various moisture contents (16-18%), screw speeds (300 & 400 rpm) at 43.4 kg/hr feed rate. Length and specific volume of Yukwa base increased with decreasing moisture contents. Hunter's color L* values of Yukwa base was higher whereas $a^*\;and\;b^*$ values were lower with increasing moisture content. Water absorption index of Yukwa base increased with increasing moisture contents. X-ray diffraction of Yukwa base showed B type moisture content of 16% and 17% while it showed A type moisture content of 18%. Degree of crystallinity and breaking strength of Yukwa base were the lowest in the moisture content of 16% while the lowest value for hardness was found in the moisture content of 16% and of 17% with screw speed 400 rpm for all samples. In the microstructure of cross section of Yukwa base, air cell size was larger and cell wall was thicker as moisture content increased. The sensory evaluation of the Yukwa base showed that color and flavor were not significantly different among samples, while taste, appearance, mouth feel, and overall preference were higher as moisture contents decreased.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.7
• /
• pp.567-578
• /
• 2015

Single droplet-wall collision heat transfer characteristics on a heated plate above Leidenfrost temperature were experimentally investigated considering the effects of impact velocity. The collision characteristics of the droplet impinged on the heated wall and the changes in temperature distribution were simultaneously measured using synchronized high-speed video and infrared cameras. The surface heat flux distribution was obtained by solving the three-dimensional transient heat conduction equation for the heated substrate using the measured surface temperature data as the boundary condition for the collision surface. As the normal impact velocity increased, heat transfer effectiveness increased because of an increase in the maximum spreading diameter and a decrease in the vapor film thickness between the droplet and heated wall. For We < 30, droplets stably rebounded from a heated wall without breakup. However, the droplets broke up into small droplets for We > 30. The tendency of the heat transfer to increase with increasing impact velocity was degraded by the transition from the rebounding region to the breakup region; this was resulted from the reduction in the effective heat transfer area enlargement due to the breakup phenomenon.

• Journal of Bio-Environment Control
• /
• v.25 no.4
• /
• pp.255-261
• /
• 2016

The present study was conducted to characterize physiological responses of aerial part according to soil water stresses in 'Mihong' peach trees. Discolorations, wilting and falling of leaves were observed in chronological order as response for waterlogging and no irrigation and the phenomena started from basal to end of shoots. Shoot growth in elongation and thickness decreased and fallen leaves were severe in waterlogged trees. Function of water uptake by roots and photosynthesis and leaf respiration decreased by waterlogging. Leaf chlorophyll contents decreased in both treatments. In waterlogging treatment, decrease of chlorophyll was observed in normal leaves with waterlogging using light microscopy. Starch content was lower in both treatment and carbohydrate content was lower in root with waterlogging. These results demonstrated that waterlogging weakened the function of soil water uptake and movement and decreased photosynthesis and fallen leaves. Finally the peach trees would wither or suffer low temperature damage through the shortage of reserve accumulations. We suggested that waterlogging damage in peach trees could be reduced to take notice of irrigation and install drainage facility to improve soil condition.

• Journal of Mushroom
• /
• v.9 no.1
• /
• pp.22-26
• /
• 2011

We bred a new strain of Pleurotus eryngii. It's name is 'Gongi No.3' and it was bred by mating monokaryotic strain isolated from E08-5D2 and dikaryotic strain GMPE25016 from 2006 to 2010 in Mushroom Research Station, Gyonggi province A.R.E.S. The characteristics of a new strain 'Gongi No.3' is as follows ; The optimum temperature for mycelium growth was from 26 to 29 degrees celsius on PDA medium and those for the premodium formation and the growth of fruit body were from 14 to 18 degrees celsius. The period of spawn running was around 30days at 22 degrees celsius and the period taken from scratching old spawn to make premodium were 8 days. The color degree of cap surface was measured by color difference meter and that of a new strain 'Gongi No.3' was 54.4 by L-value. it was seem to be dark, compared with 'Keunneutari No.2'. The hardness of fruit body of a new strain was higher than 'Keunneutari No.2'. The yield was about 180g per bottle(1100cc). it was 10g more than 'Keunneutari No.2'.

• Journal of the Korean Society of Radiology
• /
• v.5 no.6
• /
• pp.369-375
• /
• 2011

In dental radiography, panoramic views cause distortion and thus may bring about inaccurate results in the process of quantitative analysis. In this connection, there has recently been an increasing use of cone beam computed tomography (CBCT) that is known to provide high-resolution images and positional information. In this study, a dental computed tomography unit, 'DCT-90-P IMPLAGRAPHY (Vatech, Korea)', was applied to 20 patients for 24 seconds respectively, with a tube voltage of 85kVp and a tube current of 7mA. The data of CBCT were three-dimensionally reconstructed by use of a computer program, and were histomorphometrically analyzed. The results showed that the diameter of mandibular canal is less distorted at a certain inclination of the mandibular body. The image tends to seem more distended in proportion to the distance between the subject and film. Also, the image tends to be affected according as it is out of focus. In conclusion, it requires that the image should be reconstructed in light of anatomic position and structure.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.6
• /
• pp.19-27
• /
• 2004

Since the first construction of soil nailing in France in 1972, the application of soil nailing has increased. However, there is currently no design method which is universally accepted or agreed upon far soil nailed wall, because each of the design methods has different assumptions and, therefore, different approaches, moreover, since the suggested optimal inclination angles of nails are different by researchers. Therefore, the effect of nail inclination with soil nailing is analyzed by FEM. In this study, Finite element program SOILSTRUCT was applied for the effect analysis of nail inclination in soil nailed wall. For this finite element analysis, CEBTP No. 1 project data were used. The analyzed nail inclination ranged from 0$^{\circ}$ to 30$^{\circ}$ with 5$^{\circ}$ intervals. The result of finite element analysis showed that the most optimal inclination was 20$^{\circ}$ Also, the tension farce in the nails increased as the nail inclination increased. However, the effect of nail inclination on the wall deformation was very little. Therefore, constructability seems to be more important than nail inclination. Also, the tension force in the nails increases as the nail depth below the top of the wall increases, except f3r the lowest nail. Therefore, appropriate nail diameter should be used to prevent breakage of nails with considering nail strength-deformation interaction.