• Journal of the Korean Chemical Society
• /
• v.17 no.6
• /
• pp.450-454
• /
• 1973

The afterpolymerization and depolymerization of poly-${\varepsilon}$-caproamide in solid state have been studied under two different reaction conditions, nitrogen flow and sealed state. The degree of polymerization ($\bar{P}$) of nylon 6 increased with the increase in reaction time and temperature, and then reacted finally an equilibrium. In the presence of oxygen, $\bar{P}$ decreased by increasing the reaction time due to the oxidation reaction. Under certain reaction condition, the change of $\bar{P}$ for different initial degree of polymerization ($\bar{P}_0$) tendered toward unity in equilibrium.

• Polymer(Korea)
• /
• v.36 no.3
• /
• pp.302-308
• /
• 2012

The objective of this study is to investigate optimum reaction conditions for the grafting of poly($N$-vinyl- 2-pyrrolidone) (PVP) onto the surface of plasma-treated polypropylene film. The plasma treatment conditions were fixed as 200 W rf power, 6 LPM Ar flow rate, 30 sec treatment time, and 5 min exposure time after treatment. For graft copolymerization, we investigated the change of grafting degree with respect to reaction time, reaction temperature and $N$-vinyl-2-pyrrolidone concentration. Maximum grafting degree was obtained at the conditions of 6 h reaction time, $90^{\circ}C$ reaction temperature, and 40% $N$-vinyl-2-pyrrolidone concentration. The introduction of PVP was confirmed by ATR-FTIR, XPS, and SEM analysis.

• Composites Research
• /
• v.30 no.6
• /
• pp.393-398
• /
• 2017

The shrinkage distribution of a dental composite (Clearfil AP-X, Kuraray, Japan) used for dental restoration was observed using a digital image correlation method. In order to analyze the shrinkage distribution formed during and after light irradiation, digital images were taken with different photographing conditions for each period. Optimal photographing conditions during LED irradiation were obtained through a preliminary experiment in which the exposure time was applied from 0.15 ms to 0.55 ms in 0.05 ms intervals. The DIC analysis results showed that the strain was non-uniform. For the initial 20 s of light irradiation the composite resin shrank to the level of 50~60% of the final curing shrinkage. Such large shrinkage amount of the composite resin lump affected the tensile stress concentration near the adhesive region between the composite resin and the substrate.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1998.10a
• /
• pp.130-132
• /
• 1998

정밀여과막(MF)막은 $0.1~1\mum$정도의 공경을 가지고 있는 막으로 산업이나 생활분야에서 널리 사용되고 있다. 이러한 정밀여과막에 이온교환기를 부여 시키므로써, 필요로하는 금속이온이나 단백질을 흡착할 수 있는 기능성 분리막이 제조 가능하다. 방사선프라프트 중합법은 고분자를 개질, 수식 또는 기능화시키는 수법으로 사용되고 있다. 본 실험에서는 방사선그라프트중합법을 사용하여 폴리에틸렌 정밀여과막에 에폭시기를 가지는 glycidyl methacrylate(GMA)를 그라프트 중합시킨 후 이온 교환기를 도입하여, 얻어진 막의 특성에 대해 고찰하였다. 본실험의 목적은 다음과 같다. (1) 폴리에틸렌 정밀여과 막에 방사선그라프트 중합법을 사용하여 이온교환기를 도입시키는 반응조건을 검토한다. (2) 도입된 이온교환기에 다른 막의 투과 성능을 조사한다. (3) 투과법에 의한 금속이온의 흡착성능을 조사한다. 여기서, 이온교환기로서는 술폰산(sodium sulfite:$SO_3H$)을 사용하였다.

• The korean journal of orthodontics
• /
• v.34 no.4 s.105
• /
• pp.333-342
• /
• 2004

The purpose of this study was to evaluate the clinical effectiveness of a plasma arc light and light emitting diode (LED), compared with shear bond strength and the failure pattern of brackets bonded with visible light in direct bonding. Brackets were bonded with Transbond XT to 60 human premolars embedded in the resin blocks according to different light-curing methods. Then, the shear bond strength of each group was measured using a universal testing machine (Instron) and the adhesive failure pattern after debonding was visually examined by light microscope. The results were as follows: 1. The shear bond strength showed no significant difference between the visible light and light emitting diode, but the plasma arc light exhibited a significantly lower shear bond strength compared with the visible light and light emitting diode. 2. In the visible light and light emitting diode, adhesive failure patterns were similar. Bond failure occurred more frequently at the enamel-adhesive interface. 3. The bonding failure of brackets bonded with plasma arc light occurred more frequently at the bracket-adhesive interface. The results of this study suggest that plasma arc light, light emitting diode and visible light are all clinically useful in the direct bonding of orthodontic brackets.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1996.10a
• /
• pp.73-74
• /
• 1996

역삼투막은 높은 투과율과 배제율, 기계적 강도, 열적 안정성, 화학적 안정성, 성형성, 경제성 등의 여러 가지 조건을 동시에 만족시켜야 한다. 복합막을 통한 역삼투막의 제조는 위의 조건들을 만족시키는 역삼투막을 제조할 수 있는 훌륭한 제조 방법인데 지지막과 표면의 활성층을 여러 가지로 조합하여 다양한 성능의 막을 개발할 수 있기 때문이다. 지지막은 다공질의 고분자막으로 기계적 강도, 화학적.열적 안정성 등이 있어야 하는데 역삼투막이 가혹한 운전 조건에서 조작되기 때문이다. 그리고 지지막은 활성층과 안정된 결합을 할 수 있는 물리적 및 화학적 성질을 지녀야 한다. 활성층은 분리가 일어나는 곳으로 막의 배제율과 투과특성에 큰 영향을 미친다. 따라서 복합막의 제조에 있어서 고려되어야 할 사항은 지지막과 활성층의 재질의 선택, 지지막의 특성, 지지막 위에 얇고 안정된 활성층의 도포 방법, 성능향상과 활성층의 안정화를 위한 제조된 복합막의 후처리 방법 등이다. 지지막 위에 활성층을 도포시키는 방법은 계면중합법, 박층분산법, 침지코팅법, 기상증착법 등을 들 수 있는데 이 중에서 계면중합법을 이용한 복합막의 제조가 가장 실용적인 방법으로 인정되고 있고 현재 실용화되어 있다.

• Journal of Korean Ophthalmic Optics Society
• /
• v.17 no.2
• /
• pp.135-141
• /
• 2012

Purpose: Polymerization of HEMA(2-hydroxyethyl methacrylate) which can be used in the soft contact lens has been performed by using electron beam(EB) irradiation, and examined the best condition for the polymerization. Comparing the physical properties of the contact lenses to the one fabricated by thermal polymerization method, we check the use possibility of the EB irradiation to the fabrication of the soft contact lens. Methods: We investigated the degree of polymerization of the HEMA according to the composition of the monomer, the additive ratio and the dose of electron beam (0~120 kGy). The degree of polymerization was measured depending on the EB dose to research the best synthetic condition under the EB irradiation. The physical properties of the contact lens such as water content(%), oxygen transmissibility(Dk/t) and optical transmittance were analysed by using the FT-IR results with comparing the two different polymerization method (thermal and electron beam polymerization) with same additive ratio. Results: When the dose of electron beam was above 100 kGy, the degree of polymerization of HEMA was above 99% with regardless using cross-linker and initiator. The water content of the lens fabricated by EB method showed 10% higher than the one by the thermal method which was 40%. The lens fabricated by EB method also showed higher oxygen transmissibility(Dk/t) as same with the water content, and showed twice higher value in the lens fabricated by pure HEMA. According to the FT-IR results, hydrophilic property of the lens fabricated by EB method was increased due to increasing the intermolecular hydrogen bonding. It showed above 90% optical transmittance in the visible range of wavelength on the contact lenses fabricated by the both of two different polymerization method. Conclusions: The polymerization of HEMA without cross-linker and initiator was successful above 100 kGy of EB irradiation. Moreover the lens fabricated from the polymer synthesized by pure HEMA with 100 kGy of EB showed the highest water content and oxygen transmissibility. Therefore EB irradiation is another possible method to synthesize the polymer which can be used for the soft contact lens.

• Restorative Dentistry and Endodontics
• /
• v.27 no.2
• /
• pp.158-174
• /
• 2002

The aim of this study was to investigate the effect of light irradiation modes on polymerization shrinkage, degree of cure and microleakage of a composite resin. VIP$^{TM}$ (Bisco Dental Products, Schaumburg, IL, USA) and Optilux 501$^{TM}$ (Demetron/Kerr, Danbury, CT, USA) were used for curing Filtek$^{TM}$ Z-250 (3M Dental Products, St. Paul., MN, USA) composite resin using following irradiation modes: VIP$^{TM}$ (Bisco) 200mW/$\textrm{cm}^2$ (V2), 400mW/$\textrm{cm}^2$ (V4), 600mW/$\textrm{cm}^2$ (V6), Pulse-delay (200 mW/$\textrm{cm}^2$ 3 seconds, 5 minutes wait, 600mW/$\textrm{cm}^2$ 30seconds, VPD) and Optilux 501$^{TM}$ (Demetron/Kerr) C-mode (OC), R-mode (OR). Linear polymerization shrinkage of the composite specimens were measured using Linometer (R&B, Daejeon, Korea) for 90 seconds for V2, V4, V6, OC, OR groups and for up to 363 seconds for VPD group (n=10, each). Degree of conversion was measured using FTIR spectrometer (IFS 120 HR, Bruker Karlsruhe, Germany) at the bottom surface of 2 mm thick composite specimens V2, Y4, V6, OC groups were measured separately at five irradiation times (5, 10, 20, 40, 60 seconds) and OR, VPD groups were measured in the above mentioned irradiation modes (n=5 each). Microhardness was measured using Digital microhardness tester (FM7, Future-Tech Co., Tokyo, Japan) at the top and bottom surfaces of 2mm thick composite specimens after exposure to the same irradiation modes as the test of degree of conversion(n=3, each). For the microleakage test, class V cavities were prepared on the distal surface of the ninety extracted human third molars. The cavities were restored with one of the following irradiation modes : V2/60 seconds, V4/40 seconds, V6/30 seconds, VPD , OC and OR. Microleakage was assessed by dye penetration along enamel and dentin margins of cavities. Mean polymerization shrinkage, mean degree of conversion and mean microhardness values for all groups at each time were analyzed using one-way ANOVA and Duncan's multiple range test, and using chi-square test far microleakage values. The results were as follows : . Polymerization shrinkage was increased with higher light intensity in groups using VIP$^{TM}$ (Bisco) : the highest with 600mW/$\textrm{cm}^2$, followed by Pulse-delay, 400mW/$\textrm{cm}^2$ and 200mW/$\textrm{cm}^2$ groups, The degree of polymerization shrinkage was higher with Continuous mode than with Ramp mode in groups using Optilux 501$^{TM}$ (Demetron/Kerr). . Degree of conversion and microhardness values were higher with higher light intensity. The final degree of conversion was in the range of 44.7 to 54.98% and the final microhardness value in the range of 34.10 to 56.30. . Microleakage was greater in dentin margin than in enamel margin. Higher light intensity showed more microleakage in dentin margin in groups using VIP$^{TM}$ (Bisco). The microleakage was the lowest with Continuous mode in enamel margin and with Ramp mode in dentin margin when Optilux 501$^{TM}$ (Demetron/Kerr) was used.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.31 no.2
• /
• pp.280-289
• /
• 2004

Adequate polymerization is a crucial factor in obtaining optimal physical properties and clinical performance of resin composite restorative materials. The purpose of this study was to determine the effectiveness of shade and depth on dental composite resin polymerized with plasma arc curing unit employing FTIR and microhardness. From this experiment, the following results were obtained : 1. The light transmission and microhardness by mode 6 in plasma arc curing were similar to by 20 secs in halogen light curing. 2. The experimental groups of A1, A2, A3, A3.5 were not signifcant difference to light transmission and microhardness on surface and 2mm depth, but were significant difference on 3mm and 4mm depth. Especially light transmission and microhardness were small in darker shade and deeper thickness. 3. Compared with depth cure, uncured monomer amount increased at more than 2mm depth. 4. The light transmission by FTIR and polymerization by microhardness were significant corelation.

• Polymer(Korea)
• /
• v.24 no.5
• /
• pp.610-620
• /
• 2000

Vinyl acetate (VAc) was polymerized at 30, 40, and 5$0^{\circ}C$ using 2,2'-azobis (2,4-dimethylvaleronitrile) (ADMVN) and tertiary butyl alcohol (TBA) as the initiator and the solvent, respectively. High molecular weight (HMW) atactic poly(vinyl alcohol) (PVA) was prepared by saponifying the poly(vinyl acetate) (PVAc) synthesized. The effect of polymerization conditions were investigated in terms of conversion, degree of branching for acetyl group of PVAc, and molecular weight of both PVAc and PVA. The polymerization rate of VAc in TBA was proportional to the 0.49th power of ADMVN concentration in good accordance with the theoretical value of 0.5. HMW-PVA with high yield could be obtained successfully, probably due to lower polymerization temperature and decreased chain transfer reaction rate which was achieved by adopting ADMVN and TBA. PYAc having average degree of polymerization (P$_{n}$) of 10000~13000 was obtained at the conversion of 35~70%. Saponification of so prepared PVAc yielded PVA having P$_{n}$ of 2400~6100. The syndiotactic diad content increased with decreasing polymerization temperature and increasing VAc concentration due to a steric hindrance effect of TBA during polymerization.