• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2003년도 하계 학술대회 논문집
• /
• pp.156-161
• /
• 2003

농약과 방제기가 개발되면서 적은 노력과 비용으로 넓은 면적의 작물을 병과 해충으로부터 보호할 수 있게 되어 수확량이 대폭 늘어나고 농사도 안정적으로 지을 수 있게 되었다. 이렇게 방제작업이 손쉽게 되었으나 농약을 필요량보다 적게 뿌릴 경우 병해충을 충분히 방제할 수 없고, 많이 뿌릴 경우 비용과 환경오염을 증가시키는 또 다른 문제점에 부닥치게 되었다. 현재 사용되고 있는 방제기로 농약을 살포할 경우 노출된 작물의 잎에서는 농약이 흘러내리는 반면 수관내부에 감추어진 잎이나 병해충이 주로 발생되는 잎 뒷면은 농약 부착이 미흡하다. (중략)

• 대한기계학회논문집B
• /
• 제26권4호
• /
• pp.604-613
• /
• 2002

Generation characteristics of electrospray droplets for highly viscous liquid have been investigated by measuring size distributions of droplets emitted from the Taylor cone using glycerol solutions with various conductivities. Because of very small volatility of glycerol, droplet sizes can be measured by an aerodynamic size spectrometer (TSI Aerosizer DSP) with negligible evaporation of droplets. For highly conducting and viscous liquid, the sizes of the droplets electrosprayed from the Taylor cone are found to be relatively insensitive to applied voltages and the electrosprays assisted by the corona discharge call produce monodisperse droplets as long as the corona intensity is not too high. Near the minimum flow rate where a liquid cone is stable, the spray tends to consist of a one -peak monodisperse distribution of drop lets. However, at high flow rates, the spray bifurcates into bimodal distributions, which are consistent with the result of the previous study for less viscous liquids than our liquids. For liquid flow rates (Q) below 1 nl/s, the measured droplet diameters by the aerosizer are in the range of 0.30 to 1.2 ${\mu}{\textrm}{m}$ for the glycerol solutions. The diameters of monodisperse droplets scale approximately with $r^*=Q_$\tau$(Q$\tau$){^1/3}$ where $r^*$ is a characteristic length and $\tau$is the electrical relaxation time of the fluid. However, when compared with several represe ntative scaling laws, the droplet diameters are two to six factors greater than those predicted by the scaling laws. This may be closely related to the combined effect of the much higher viscosity and the electrical charge on the jet breakup of glycerol so solution.

• 대한기계학회논문집B
• /
• 제25권10호
• /
• pp.1400-1407
• /
• 2001

The size distributions of electrospray droplets from the Taylor cone in cone-jet mode are directly measured by using a freezing method and a transmission electron microscope (TEM) image processing technique. These results are compared with the data obtained by an aerodynamic size spectrometer (TSI Aerosizer DSP). The use of glycerol seeded with NaI and a freezing method make it possible to sample droplets with their original sizes preserved. Since pictures of droplets are taken with TEM with very low vapor pressure of the solution, evaporation is suppressed by freezing. For liquid flow rates below 1 nl/sec, the measured droplet diameters by the TEM image processing technique and the aerosizer are in the range of 0.25 to 0.32 m add 0.3B to 0.40m, respectively. Comparing the TEM data with the aerosizer measurements, it has been revealed that the TEM image processing technique can afford more accurate values of droplet size distributions in the submicron range of 0.1 to 0.4m.

• 한국대기환경학회지
• /
• 제26권3호
• /
• pp.339-345
• /
• 2010

There have been a number of efforts to satisfy national emission regulations and reduce the amount of emitted air pollutants. There are several air pollution control devices, however, only wet scrubber is efficiently used to remove particulate matters and gaseous pollutants, even if it has minimum collection efficiency in the particle size range of $0.1{\sim}1{\mu}m$. This study aimed to improve the collection efficiency of a spray tower type scrubber by introducing an electrospray system with two-flow nozzle. We found that the collection efficiency of a spray tower type scrubber was similar to that of a conventional wet scrubber. However, installation of an electrospray system in the scrubber resulted in drastic further improvement of collection efficiency comparing to that of a conventional scrubber, which is 26%, 35.2%, and 45.1% at the liquid to gas ratio of 0.26 $L/m^3$ and 19.9%, 35.1%, and 42.5% at 0.34 $L/m^3$ for the applied voltage of -30 kV, -35 kV, and -40 kV, respectively. Therefore, we found that the introduction of an electrospray system is very effective to improve the collection efficiency of a spray tower type scrubber.

• 한국기계가공학회지
• /
• 제15권2호
• /
• pp.118-124
• /
• 2016

In this study, experiments are conducted to improve spray coating uniformity by using second and third electrodes based on the electrospray atomization mechanism. The uniformity of fabricated thin films can be improved by adjusting the design of the second electrode. The implementation of the second electrode with an elongated hole and a bending angle of $90^{\circ}$ results in highly uniform films. In addition, induced area to substrate is increased by lowering the applied voltage using the third electrode with a round rod shape. A linear correlation between applied voltage and induced area is confirmed. Thin film thickness and surface roughness are measured after the fabrication of thin films through the electrospray process. It is confirmed that a thin film is formed having an average thickness of 273.44 nm, a thickness uniformity of less than 10%, and a surface roughness of 3 nm.

• 한국분말재료학회지
• /
• 제18권6호
• /
• pp.526-531
• /
• 2011

Fecralloy is the promising materials for high temperature exhaust filtering system due to the excellent its oxidation resistance property. In this research, Fecralloy nanoparticles coated Fecralloy thin foil was prepared by a single nozzle electrospray system in order to increase surface area of Fecralloy foil. Fecralloy nanoparticles were fabricated by electrical wire explosion method in ethanol using Fecralloy wires as a source material. Electrospray modes with applied D.C voltages to Fecralloy colloidal solution were investigated to make a stable cone-jet mode. Coated layers with and without additional heat treatment were observed by FE-SEM (field emission-scanning electron microscope) and tape test for evaluating their adhesion to substrate were performed as well.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제52권12호
• /
• pp.573-578
• /
• 2003

In this study, new type of induction charging system for electrostatic spraying was manufactured and proposed to improve the electrical safety and charging efficiency. And parameters of proposed system to generate the maximum deposition current with electrical safety were selected and investigated. The selected parameters were frequency of square pulse and thickness of insulation material, outer diameter of device and thickness and positions of electrode. Charging quantity of water drop was measured by deposition current detected from sensing plate indirectly. The maximum deposition current for each parameter were 3.5[uA] at the frequency of 15[kHz] and thickness of 0.25[mm] insulating layer. And maximum deposition currents were 2.8[uA] and 3.0[uA] at 25[mm] outer diameter of charging device and 0.25[mm] thickness of electrode each. Effects of electrode position from spraying nozzle on deposition current was a little.

• 한국결정성장학회지
• /
• 제20권2호
• /
• pp.69-73
• /
• 2010

정전분무증착 기술에 의해 증착된 고체산화물 연료전지(SOFC) 양극재료인 SSC 양극막의 미세구조적 변화에 대해 연구하였다. Samarium chloride hexahydrate$(SmCl_3{\cdot}6H_2O)$, strontium chloride hexahydrate$(Co(No_3)_2{\cdot}6H_2O)$, cobalt nitrate hexahydrate$(Co(No_3)_2{\cdot}6H_2O)$의 출발 물질과 용매로써 메탄올이 전구체 용액을 제조하는데 사용되었다. SOFC의 양극을 위해 적합한 다공성의 SSC 막을 제조하였으며, 그 미세구조가 증착시간, 기판온도, 인가전압 등과 같은 공정변수들에 의존한다는 것을 관찰하였다. 주사전자현미경과 X-ray 회절 패턴이 미세구조와 결정성 분석을 위해 사용되었다. 본 연구를 통해, ESD 기술이 요구하는 상의 합성과 다공성의 미세구조를 갖는 SOFC의 양극막을 제조하는데 효과적인 방법임을 입증하였다.

• 전기학회논문지
• /
• 제67권10호
• /
• pp.1317-1321
• /
• 2018

PVDF as a semicrystal polymer, having a structure with C-F dipole moments, has been widely investigated because of its excellent chemical stability, mechanical strength, and ferroelectricity. In this study, ferroelectic ${\beta}$ type - PVDF layer was prepared by using an electrostatic spray deposition method and the effects of the addition of Ni-nitrate in precursor solution on the properties of PVDF layer were evaluated. Crystallinity and chemical structure of the PVDF layer were analyzed by a X-ray diffraction and Fourier Transform Infrared Spectrophotometer. Surface structure and fractured cross section of the layer were examined by a field emission-scanning electron microscope. LCR meter was used to obtain the dielectric properties of the layer. As the addition of an inorganic metal salt in PVDF sol, ${\beta}$ type - PVDF crystals were appeared in the hydrated metal salts doped-layer since the strong hydrogen bondings $(O-H{\cdots}F-C)_n$ due to high polarity of OH- were formed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.1423_1424
• /
• 2009

Dye sensitized solar cells(DSC) have been very economical and easy method to convert solar energy to electricity. DSC can reach low costs in future outdoor power applications. However, to commercialize the DSC, there are still many shortages to overcome such as a low efficiency in a large size DSC. In this study, DSCs were fabricated by an electrospray coating method for the $TiO_2$ thin film. They were compared with DSCs prepared by conventional coating methods. We conducted an experiment to obtain the optimized parameters of voltage, flow rate, incident angle and distance in the electrospray method. After we manufactured $TiO_2$ film using that way, we could analyze the characteristics of DSC through SEM, UV curve, EIS.